IBM Travelstar 14GS User manual

Quick installation guide
Travelstar 14GS
AT/IDE
Models: DCYA-214000
IBM storage products
Page 1
IBM Hard Disk Drive Technical Support Center version 2.0
Handling precautions
1. Do not cover the breather hole! Covering the
breather hole may result in loss of data.
2. Do not press on the drive! Do not apply any force
to the drive during handling or installation.
3. Always handle the drive with care to prevent
damage from shock, vibration, or electrostatic
discharge (ESD).
4. Do not open the static-protective bag containing the
drive until required. Static electricity can damage the
drive.
5. Turn off and unplug your computer. Remove the
cover.
6. When you are installing the drive, touch the static-
protective package containing the drive to a grounded,
unpainted metal surface for at least two seconds.
(This drains static electricity from the package and
from your body.)
7. Handle the drive carefully by the edges. Do not
touch any exposed printed circuit board.
8. Save your drive packaging material including the
ESD bag in the event he drive has to be returned.
Place the drive in an anti-static bag before placing it in
the shipping container. The warranty will be void if
the drive is not returned in IBM approved packaging.
Quick installation procedure
Note: It is advisable to backup all data before
proceeding with the installation.
If your system BIOS cannot handle large capacity
drives (over 540 MB), you may need to use a disk
overlay program such as Ontrack’s Disk Manager.
The following procedure uses the Ontrack Disk
Manager software. Information on obtaining a copy of
Ontrack’s Disk Manager can be found on the Web at
www.ibm.com/harddrive.
Setting the jumpers
1. In a one drive system, configure your new drive as
Master (Device 0) with no jumpers installed.
2. In a two drive system, one drive must be desig-
nated as the Master, the other as the Slave (Device 1)
3. When installing the new drive as a Slave, check the
Master drive to determine if a jumper change is
required to indicate that a Slave drive is present.
4. Consult your manual to see if your computer
supports Cable Select before choosing this option.
No Jumper
(Master) Jumper Pos-1 (Slave) Jumper Pos-3
(Cable Select)
Never Attach A
Jumper Here!
Never Attach A
Jumper Here!
Note: Pin 20 is left blank for secure connector insertion.

IBM storage products
Page 2
IBM Hard Disk Drive Technical Support Center version 2.0
Attaching the drive
1. Turn off the computer, unplug the power cord, and
open the cover.
2. Match pin 1 of the 44 pin cable to pin 1 of the drive
interface connector. Pin 1 is usually denoted by a
stripe along the edge of the cable.
3. Mount the drive securely.
Configuring your computer
1. If your computer has a plug-in IDE card with a
drive installation procedure, follow the manufacturer’s
instructions.
2. Plug in the power cord and power on your com-
puter. Your computer may detect a configuration
change and prompt you to proceed to the Setup
screen.
3. If your computer does not prompt you to
reconfigure, enter your computer’s Setup, typically by
key selection or keyboard combinations during
power-on or during a reboot. Refer to your
computer’s documentation for the proper key
sequence. If the computer fails to boot up, power off,
remove the new hard drive and return your system to
its original configuration. Reboot and enter your
computer’s Setup. Follow the directions in step 4,
then reattach the new hard drive.
4. Select “Auto Detect” if your computer Setup sup-
ports this feature. If your computer does not Auto
Detect the drive, select the appropriate UDT (User
Definable Type) for the model being installed.
Then run Disk Manager.
14,130 MB631616,383DCYA-214000
CapacitySector
/Track
HeadsCylindersIBM Model
Number
Running Disk Manager
1. Boot to operating system from the hard drive or the
diskette.
2. Insert the Ontrack diskette.
3. Type DM and press [ENTER] to run Disk Manager.
4. Under “Select an Installation Option”, select (E)asy
Disk Installation.
5. Select a drive for installation; Disk Manager will
partition and format the drive.
6. A status dialog will indicate a successful instal-
lation.
If, after complete installation, your system will not
boot up, recheck all settings. If the system still fails to
boot up, remove the new drive from your system to
return to your original configuration and contact tech-
nical support.
©International Business Machines Corporation 1999
www.ibm.com/harddrive
IBM Hard Disk Drive Technical Support Center
3605 Highway 52 North
Rochester, MN 55901
Telephone: 888.IBM.5214 or 507.286.5825
Fax: 507.253.DRIVE
E-mail: [email protected]
Singapore Technical Support Center
Telephone: [phone] or 1800.418.9595
E-mail: [e-mail]
IBM Storage Systems Division
5600 Cottle Road
San Jose, CA 95193
www.ibm.com/storage
Printed in the United States of America
01-99
All Rights Reserved
IBM is the registered trademark of International Business Machines Corporation.
Other company, product, and service names may be trademarks or service marks of others.
Produced by the IBM Hard Disk Drive Technical Support Center.
OEM Hark Disk Drive Specification for DCYA-214000,revision 1.0
Product Description data represents IBM’s design objectives and is provided for
comparative purposes; actual results may vary based on a variety of factors. This product
data does not constitute a warranty. Questions regarding IBM’s warranty terms or
methodology used to derive this data should be referred to your IBM representative. Data
subject to change without notice.
Date: 11 January 1999
®