Icom IC-905 Instruction Manual

|905
CONNECTION GUIDE
ALL MODE TRANSCEIVER
Thank you for choosing this Icom product.
READ ALL INSTRUCTIONS carefully and completely
before using this product.
–1 –
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A7711D-2EX Printed in Japan
© 2023 Icom Inc.Feb. 2023
–4 –
Icom and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany,
France, Spain, Russia, Australia, New Zealand, and/or other countries.
Connecting the RF unit and the controller
TIP:
To prevent water from seeping into the connection
After connecting, cover the connectors and Ferrite EMI lter
with the supplied or user supplied rubber vulcanizing tape.
About an external DC power supply
The transceiver needs:
• 13.8 V DC
• A power supply with an over current protective line, and
low voltage uctuation or ripple.
LConrm that the power supply is OFF before connecting
the DC power cable.
Connect the RF unit and the controller, as shown below.
LPrepare antennas and cables, suitable for your operating
environment.
NOTE: Attach the connector cap when no equipment is
connected.
Supplied rubber
vulcanizing tape
Rubber
vulcanizing tape
(User supplied)
Connect the antennas.
1
Coaxial cable
(User supplied)
To the antenna for the 144 MHz,
430 MHz, and 1200 MHz band
To the antenna for
the 2400 MHz band
To the antenna for
the 5600 MHz band
Coaxial cable
(User supplied)
RF unit
RF unit’s top panel
RF unit’s bottom panel
Controller
To
[DC 13.8 V] jack
Supplied DC
power cable
Control cable*
To [RF UNIT] connector
Connect the DC power
cable, and then push
[POWER] to turn ON the
transceiver.
3
Connect the RF unit
and controller with the
control cable.
2
Important
FIRST, CAREFULLY READ BASIC MANUAL that is boxed
with the transceiver.
SAVE THESE INSTRUCTIONS— These instructions
contain installation instructions for the IC-905.
The Connection Guide for German, Spanish, French, and
Italian is at the end of the Basic manual for each respective
language.
* The following cables are usable, depending on your operating environment.
Supplied control cable: 5 m (16.4 feet)
Optional OPC-2513 control cable: 20 m (65.6 feet)
Optional OPC-2509 control cable: 50 m (164.0 feet)
Requirements for attaching and connecting
Control cable for connecting
Controller and RF unit
(5 m: 16.4 feet)
GPS antenna
Bracket
Assembled screws
for bracket
(6 × 15 mm)
Screws and washers
for attaching to a pole
U-boltsPole clampsDC power cable
(1.5 m: 4.9 ft)
IC-905
(Controller)
IC-905
(RF unit)
Rubber
vulcanizing tape
BE CAREFUL! When you install the IC-905’s RF unit and
antenna, wear gloves to avoid cutting your hand on the
sharp edges of the metal parts or antenna.
Icom is not responsible for any building breakage, any
damage resulting from a drop of the mounting bracket from
a high place or unstable site, or any personal injury or any
accident in any other case. Be sure to consult an expert
engineer for installation help.
Supplied control
cable
To the RF unit
Ferrite EMI lter
Attach the Ferrite EMI lter to
the DC power cable.

–3 –– 2 –
Attaching the RF unit to a pole
Attach the assembled
screws and GPS
antenna to the RF unit.
Attach the bracket
to a pole.
Attach the RF unit to the
bracket, and then tighten the
assembled screws.
Attach the RF unit to a pole, as shown below. CAUTION: Attach the RF unit in a vertical position with the
ACC connector down. The water jet resistance cannot be
guaranteed if you attach the RF unit upside down.
RF unit
(Approximately 3.2 kg, 7.1 lb)
GPS antenna
Assembled screw
Flat washer
Spring washer
Nut
U-bolt
Pole clamp
Bracket
Pole
40 ~ 60 mm
1 2 3
Torque: 5 N•m
Grounding
To prevent electrical shock, television
interference (TVI), broadcast
interference (BCI) and other
problems, ground the RF unit and
controller.
For best results, connect a heavy
gauge wire or strap to a long ground
rod. Make the distance between the
ground terminal and ground as short
as possible.
RWARNING! NEVER connect the
ground terminal to a gas or electric
pipe, since the connection could
cause an explosion or electric shock.
Assembled screw
Grounding cable
(User supplied)
RF unit Controller
Grounding cable
(User supplied)
Dimensions
IC-905 RF unit with the bracket unit: mm (inch)
135.5 (5.3) 188.3 (7.4)
248.4 (9.8) 222.0 (8.7)
456.2 (18)
About the operating environment
• Communication may be temporarily unavailable or
interrupted when:
- The received signal is too weak.
- There is heavy rain or snow.
- Snow or ice accumulates on the RF unit or external
devices.
• When using in a cold location, DO NOT bend, pull,
or move the cable if the cable is hardened. This may
damage the cable.
Selecting a location
NEVER place the transceiver and antenna in areas such as:
• The RF unit and controller cannot be connected using the
supplied or optional control cable.
LOperation cannot be guaranteed if you:
- Cut or extend the control cable.
- Use other than the specied cable.
LThe RF unit accepts the power through the control cable.
• A place without adequate ventilation or that gets wet with
rain. (Only for the controller)
LThe controller does not have the dust-protection and water jet
resistance.
• An unstable place that slopes or vibrates.
• Too close to each other or other devices, such as TV
antennas.
• Near a radio tower emitting strong radio waves.
• Near a metal structure, such as warehouses.
LIf there is a metal wall, handrail, or pillar where the radio wave
from the antenna travels, the radio wave may be reected
irregularly.
• A place without direct lightning protection, such as
lightning rods.
• A place without grounding.
• A place that the transceiver cannot receive signals from
the GPS satellites.
LThe IC-905 automatically adjusts the internal reference
frequency using the received GPS data as the default setting.
NOTE:
• Make the connection as short as possible.
• Use a coaxial cable (user supplied) that is as low loss as
possible.
• DO NOT bend the coaxial cable more than the allowable
bending radius. This may cause more losses.
Important notes
RWARNING! NEVER disassemble, modify, or repair the
transceiver. This may result in an electrical shock, cause a
re or damage the transceiver.
• NEVER use the RF unit without securing the cables so
that they cannot be pulled or stretched.
• Attach the RF unit in a vertical position with the ACC
connector down. The water jet resistance cannot be
guaranteed if you attach the RF unit upside down.
• NEVER immerse the RF unit in water. The RF unit
meets IP55* requirements for dust-protection and water
jet resistance. However, once the RF unit has been
dropped, dust-protection and water jet resistance cannot
be guaranteed due to the fact that the RF unit may be
cracked or the waterproof seal damaged, and so on.
* Only when the connector covers are attached.
• BE SURE to check your local regulations or laws to select
the appropriate operating frequency.