ICP DAS USA 7188EN Installation guide

Copyright @ 2016 ICP DAS Co., LTD. All Rights Reserved. - 1 -
分類/Classification
tDS
tGW
PETL/tET/tPET
DS/PDS/PPDS
tM-752N
I/O Card
VXC Card
VxComm
7188EN
作者/Author
Tammy
日期/Date
2016-01-12
編號/NO.
FAQ-043
Q: How to enable web server for the PDS/7188EN series module?
A: The PDS/7188EN series module contains a built-in web server that allows the settings for the module to
be remotely modified via a web interface. When the web server has been disabled (Web Server = 0), refer
to the following two methods to enable the web server.
Method 1: Enable web server on PDS by using “console port and command”.Follow the procedure
described below:
1. Power off the PDS module.
2. Connect the download-cable (CA0910), between the PDS and COM4 of the development PC.
3. Wire the CA-0910 to PDS, as follows:
Connect the CA-0910.TX with PDS.TxD
Connect the CA-0910.RX with PDS.RxD
Connect the CA-0910.GND with PDS.GND
4. Set the “Init/Normal Switch”on the PDS module to the in “Init”position.
(Or connect the INIT* pin to the GND pin.)
5. Power on the PDS module.

Copyright @ 2016 ICP DAS Co., LTD. All Rights Reserved. - 2 -
6. Unzip the “7188XW_yyyymmdd.zip” file on the PC. The “7188XW_yyyymmdd.zip”can be obtained
from the ICP DAS web site (http://ftp.icpdas.com/pub/cd/8000cd/napdos/minios7/utility/).
7. Open “Notepad”text editor for Windows and type the command: C4 B115200 P0D8 S1, and then save
the file as “7188xw.ini”in the same directory of 7188XW.exe.
8. Execute “7188XW.EXE”and press [Enter] key.
9. Settings configuration command:
The following is an example of a HTTP configuration.
Command
Description
HTTP= 1
Enables the Web Server.
HTTP= 0
Disables the Web Server.
Enable Web Server
C: COM Port of the development PC (e.g., C4)
B: Baud Rate (e.g., B115200)
P: Parity None (e.g., P0)
D: Data Bits (e.g., D8)
S: Stop Bits (e.g., S1)

Copyright @ 2016 ICP DAS Co., LTD. All Rights Reserved. - 3 -
Method 2: Enable web server on PDS by using “TCP port 10000”.Follow the procedure described below:
1. Ensure that the network settings on the Host PC have been correctly configured and are functioning
normally. Connect both the PDS module and the Host PC to the same sub network or the same
Ethernet Switch, and apply power to the PDS module.
2. Configure the correct network settings for the required PDS module. Refer to PDS Quick Start Guide for
more detailed information.
(http://ftp.icpdas.com/pub/cd/8000cd/napdos/pds/pds-700/document/quick_start/)
3. Download the “Terminal.exe”on your PC, or use other telnet client program. The “Terminal.exe”can
be downloaded from the ICP DAS web site.
(http://ftp.icpdas.com/pub/cd/tinymodules/napdos/software/)
4. Double click the “Terminal.exe”to open “Configuration Settings”dialog box.
5. Click the “TCP/IP Port”tab to configure the parameters as follows:
5-1: Type the “IP address of the PDS module”in the “IP Address”field.
5-2: Type the “10000”in the “TCP/IP Port”field.
5-3: Click the “Open COM”button.


Copyright @ 2016 ICP DAS Co., LTD. All Rights Reserved. - 4 -
6. Select the “Hex/Text”option in the “Display”filed and settings configuration command:
Command
Description
26SAVE=1, HTTP=1
Enables the Web Server and save the configuration to EEPROM.
26SAVE=1, HTTP=0
Disables the Web Server and save the configuration to EEPROM.
7. Type the “26SAVE=1, HTTP=1”string in the “send”field then click the “Send”button.
8. If the response is received, it will be displayed in the received field that means the success.
9. Reboot the PDS module to complete the configuration.


