ICP DAS USA Zigbee ZT-2060 User manual

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 1
ZT-2060
Zigbee Wireless 6-channel Digital Input, 4-channel
Relay Output Module
Quick Start Guide
Product Website:
https://www.icpdas-usa.com/zt_2060.html
Introduction
The ZT-2060 offers 4 Form A power relay output channels and 6 digital input
channels, each of which features photocouple isolation. In addition, you can
choose sink-type or source-type input via wire connections. All channels are able
to be used as 16-bit counters. The ZT-2060 has 10 LED indicators to display the
channel status, and has 4 kV ESD protection and 3000 VDC intramodule isolation.
Users can easily configure the module address, protocol, checksum, ZB-PID and
ZB-channel settings using a combination of rotary and DIP switches.
1 What’s in the Shipping Package?
The shipping package contains the following items:
ZT‐2060 DIO Device ANT‐124‐05 Quick Start

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 2
2 Preparing the Device
1. Refer the chapter 3. to configure the DIP switch of ZT-2060 I/O device.
2. Install the ZT Configuration Utility to configure the ZT-2060 coordinator.
CD:
\Napdos\ZigBee\ZT_Series\Utility http://ftp.icpdas.com/pub/cd/usbcd/nap
dos/zigbee/zt_series/utility
3. Power Supply: +10 ~ +30 VDC
3 Setting up the ZT‐2060 DIO Device
3.1 Introduction to the Configuration Parameters
A. “Pan ID” parameter is the group identity for a ZigBee network, and
must the same for all devices in the same ZigBee network.
“Address/Node ID” parameter is the individed identity of a specific
the ZigBee module, and must be unique for each device connected the
same ZigBee network.
B. “RF Channel” parameter indicates the radio frequency channel, and must
be set to the same value as other modules on the same ZigBee network.
Channel
0x00
0x01
……
0x0F
Frequency(MHz)
2405
2410
……
2480
※RF channels 0x04, 0x09, 0x0E or 0x0F are recommended because they do
not overlap with the Wi-Fi frequencies based.
802.11b/g
802.11b/g
802.11b/g
Channel 1
Channel 6
Channel 11
2400 00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F 2485
MHz
MHz
802.11b/g Channel (North America)

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 3
802.15.4 Channel
C. Protocol/Application Mode：
When implementing custom programs based on different protocols, the
following application modes are recommended in order to ensure
communicatible
User Program Protocol
DCON
Modbus RTU
Modbus TCP
ZT-2060 I/O
ZT-2550
ZT-2570
DCON
Transparent
Transparent
Modbus RTU
Transparent
Transparent
Modbus Gateway
Modbus Gateway
Modbus RTU
------
Modbus Gateway

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 4
4 Rotation Switch and DIP Switch
The configuration of ZT-2060 series can be adjusted by using the
external rotary switch and the DIP switches. The ZT-2060 device should
only be rebooted once the configuration is complete.
 DIP Switch to the ZT‐2042/ZT‐2043/ZT‐2060/ZT‐2055
Protocol Pan ID
ON
1
2
3
4
5
6
7
8
9
10
11
12
Checksum
RF Channel
Reserved
Address LSB
Address MSB
(Node ID)
(Node ID)
 DIP Switch to the ZT‐2060/ZT‐2060
Protocol Pan ID
Address LSB
Address MSB
Checksum
RF Channel
(Node ID)
(Node ID)

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 5
 Rotation Switch
0
1
2
3
……
F
Note
Address
SW
01
02
03
……
0F
MSB = 0
Node ID
SW
0x0001
0x0002
0x003
……
0x000F
0
1
2
3
……
F
Address
10
11
12
13
……
1F
MSB = 1
Node ID
0x0010
0x0011
0x0012
0x013
……
0x001F
※Once the address of hardware switch is set to 0x00, it mens the address is using
software configurations. Refer the more detailed information at Sec. 6.6 of user
manual.
 DIP Switch
Number
Item
Status
Explain
1
Address MSB
OFF
Valid Address (Node ID) from 0x00 to 0x0F
ON
Valid Address (Node ID) from 0x10 to 0x1F
2
Protocol
OFF
DCON Protocol
ON
Modbus RTUProtocol
3
Checksum
OFF
Disabled
ON
Enabled
4
ZigBee Pan ID
OFF
Pan ID = 0x0000
ON
Pan ID = 0x0001
5
OFF
------
ON
0x08
6
OFF
------
ZigBee
ON
0x04
RF Channel
7
OFF
------
ON
0x02
8
OFF
------
ON
0x01

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 6
5 Start‐up ZT‐2000 I/O Device
As the ZigBee network is controlled by the ZigBee coordinator, the ZT-
2550/ZT-2570 (ZigBee coordinator) must be configured first. Please refert to
documents shown below for full details of how to configure these devices.
Once configuration of the ZigBee coordinator has been completed. Set
the ”Pan ID” and the “RF Channel” values for the ZT-2000 I/O device to the
same values as the network, and then reboot the device. The module will
automatically start to function on the ZigBee network using the default protocol.
※Configuration Utility (Used to configure ZT-2000 I/O device Coordinator)
http://ftp.icpdas.com.tw/pub/cd/usbcd/napdos/zigbee/zt_series/utility/

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 7
6 Examples
 Configurations of ZT‐2550/ZT‐2570
 Configurations of ZT-2000 I/O Device
12345678910 11 12
1
2
3
4
5
6
7
8
ON
Number
Item
Status
Explain
1
Address MSB
OFF
Address/Node ID is 01(Rotation Switch=1)
2
Protocol
ON
Use Modbus RTU Protocol
3
Checksum
OFF
Disabled
4
ZigBee Pan ID
OFF
Pan ID=0x0000
5
ON
0x08
6
ZigBee
ON
0x04
ZigBee RF Channel = 0x0E
7
RF Channel
ON
0x02
8
OFF
------

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 8
7 Communication Test
Once the ZT-2000 I/O device has joined the ZigBee network, the signal
quality can be comfirmed by monitoring the status of the ZigBee Net LED
indicators. If the LED indicator shows a steady light, communication with
the ZT-2000 I/O device has been successfully established for data
acquisition and control.
ICP DAS also provides the “DCON Utility”, which can be used to
simulate DCON/Modbus communication. This software can also be used
to verify the device settings and ZigBee I/O functions.
※The DCON Utility can be dowmload from:
http://ftp.icpdas.com/pub/cd/8000cd/napdos/driver/dcon_utility/
Simulate I/O channel operating via using DCON Utility
1. Launch DCON Utility and select the correct COM Port settings to
connect the ZigBee Coordinator (ZT-2550/ZT-2570).
2. Clicking “Search” button will start searching which ZT-2000 I/O device
is in the same ZigBee network.
3. If there is any ZT-2000 I/O devices displayed, double clicking the
“module name” will start the I/O channels operated platform.

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 9

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 10
8 Troubleshooting
(1) Technical Support.
If you have any difficulties using your ZT-2000 series I/O device,
please send a description of the problem to [email protected]om
Include the following items in your email:
A description or diagram of the current DIP switch positions.
A copy of the configuration file for the ZT-2000 coordinator. This file
can be obtained using the procedure outlined below and should be
attached to your email.
a. Set the DIP switch of the ZT-255x device to the [ZBSET] position then
reboot the device. Launch the ZT Configuration Utility and select [Save
Log] icon to save the configuration of the ZT-255x as a file.
b. After clicking the [Save Log] icon, enter the “File Name” and the “File
Path” in the Windows “Save” dialog box. Once the configuration has
been successfully saved, the following message will be displayed.