ICP DAS USA VPD-173X User manual

Technical support: servic[email protected]om P1
VPD-173X/173X-64
Quick Start
v1.2, Apr. 2019
What’s in the box?
Related Information
Thanks for buying ICPDAS VPD-173X/173X-64 device. This shipping
package contains the following items:
VPD-173X/173X-64 x 1
Quick Start x 1 (This Document)
2.4 mm Screw Driver x 1
Panel Mounting Kit x 1
If you are new to VPD-173X/173X-64, please read the “Chapter 3.
Getting Started” of the TouchPAD Hardware User Manual for
detailed information about install the free development tool –
HMIWorks and how to create your first project.
Documents, such as the User Manuals, the API References,
etc.: http://ftp.icpdas.com/pub/cd/touchpad/document/
Free Development Software, HMIWorks v2.10.24 or above:
http://ftp.icpdas.com/pub/cd/touchpad/setup/
If you have any questions, please feel free to contact us via email.

Technical support: servic[email protected]om P2
1 Appearance
Front View Rear View Left View
2 Pin Assignments
Pin
Description
COM2
Tx
The pin of transmitted data of the RS-232
Rx
The pin of received data of the RS-232
GND
Ground pin
D-
The negative data line of the RS-485 network
D+
The positive data line of the RS-485 network
COM1
Tx
The pin of transmitted data of the RS-232
Rx
The pin of received data of the RS-232
GND
Ground pin
D-
The negative data line of the RS-485 network
D+
The positive data line of the RS-485 network
Power
F.G.
Frame Ground. F.G. is connected to the inside EMI or
ESD suppression circuits. Make sure that F.G. is
connected to the Earth
P.GND
Connected to the power supply’s ground pin
PWR
DC input Voltage (range: +12 V ~ +48 V)
LED
Indicator
Ethernet
Serial Port
Rotary
Switch
Reset
Button
Power Port
COM2
COM1
Power
F.G.
PWR
P.GND
7” LCDTouch
Panel
XV-Board
(optional)
USB

Technical support: servic[email protected]om P3
3 Rotary Switch & Default Settings
The definition of the rotary switch:
No
Mode
Description
0 Run & Update
(Ethernet)
This is a special run mode which is used in
the development stage. The TouchPAD
device
can be updated by a PC from the
remote side through Ethernet. (Default)
1 Ethernet
Force
Update
While the application run on the TouchPAD
device seriously crashes, use this mode to
update a new application to the TouchPAD
device through Ethernet.
2 Run Only Run the program.
9
USB Force
Update
Update a new application to the TouchPAD
device through USB.
Network Default Settings
IP Address
192.168.255.1
Subnet Mask
255.255.0.0
Gateway
192.168.0.1
4 First Use of the VPD-173X Series
1. Connect wires as the below figure
or prepare an Ethernet cable which
will be used to supply power through
PoE if there’s a RJ-45 Ethernet port
on it. And set the rotary switch to 0
(At this point, the power is not yet
supplied).
Use a flat-head screwdriver to set
rotary switch
PoE Switch
GND
VDC (+12-+48 V)
External Power

Technical support: servic[email protected]om P4
2. Supply power to the VPD-173X/173X-64
wait for several seconds and then you can
see the default program run on it.
3. Try to touch on the icons on the
bottom-right corner of the screen of the
VPD-173X /173X -64
and you can find that
VPD-173X/173X-64 switches to the setting pages.
5 Hardware Installation
The panel mounting of VPD-173X/173X-64
Insert the panel mounting clips into the
upper and lower ventilation holes.
Screw the panel
mounting clips to
the
panel.
(Mounting Screw:
M4 x
15L)

Technical support: servic[email protected]om P5
VPD-173X/173X-64
快速入門指南
v1.2, 2019 年4月
檢查配件
參考資訊
感謝您購買泓格的 VPD-173X/173X-64 產品。產品包裝內應包含下列
配件:
VPD-173X/173X-64 x 1
產品須知 x 1 (本文件)
24 mm 螺絲刀 x 1
面板安裝組件 x 1
如果您是第一次使用 VPD-173X/173X-64，請參閱 TouchPAD 硬體
使用手冊的 “第3 章啟動 TouchPAD” 來了解如何安裝免費的開發
軟體 HMIWorks 並建立第一個專案以及更多詳細的相關資訊。
相關文件，如使用手冊、應用程式介面指南(API Reference) 等:
http://ftp.icpdas.com/pub/cd/touchpad/document/
免費開發軟體，HMIWorks 版本 2.10.24 或以上版本:
http://ftp.icpdas.com/pub/cd/touchpad/setup/
如有任何問題歡迎使用 E-mail 聯繫我們，我們將會為您提供完善的咨
詢服務。

Technical support: servic[email protected]om P6
1 外觀
前配置圖 後配置圖 左配置圖
2 腳位定義
Pin
說明
COM2
Tx
RS-232 的傳送資料腳位
Rx
RS-232 的接收資料腳位
GND
接地端
D-
RS-485 網路的負訊號線
D+
RS-485 網路的正訊號線
COM1
Tx
RS-232 的傳送資料腳位
Rx
RS-232 的接收資料腳位
GND
接地端
D-
RS-485 網路的負訊號線
D+
RS-485 網路的正訊號線
Power
F.G.
機架接地，F.G. (連接到內部的 EMI 或ESD 保護電
路)，請接到大地
P.GND
連到電源的接地端
PWR
直流電壓輸入 (範圍：+12 V ~ +48 V)
Ethernet
電源埠
7” 吋觸控
液晶螢幕
LED
指示燈
序列埠
旋轉
開關
重啟
按鈕
COM2
COM1
Power
F.G.
PWR
P.GND
USB
XV-Board
(選購)

Technical support: servic[email protected]om P7
3 旋轉開關及出廠預設值
旋轉開關的配置模式定義:
No
模式
說明
0 Run & Update
(Ethernet) 執行/更新程式，用於程式開發階段 (能 執行程式，也能進行更新)。(出廠預設)
1 Ethernet
Force Update 強制更新，當 TouchPAD 上的程式嚴重 毀損時可用此模式透過 Ethernet 更新。
2 Run Only 執行程式。
9
USB Force
Update
透過 USB 更新程式。
網路設定出廠預設如下表:
IP Address
192.168.255.1
Subnet Mask
255.255.0.0
Gateway
192.168.0.1
4 第一次使用 VPD-173X 系列
1. 如下圖所示，將電源和接地線連接
完成。或是有 RJ-45的乙太網路接孔，
可以準備一條網路線，透過乙太網路供
電(PoE)。然後將旋轉開關 (Rotary
Switch) 轉到 0 (此時尚未供電)。
乙太網路
供電
使用一字起子
來配置旋轉開關
外部供電器
GND
VDC (+12-+48 V)

Technical support: servic[email protected]om P8
2. 開始供電給 VPD-173X/173X-64，等待約
數秒的開機時間，接著可以看到
VPD-173X/173X-64 執行出貨預附的程式如
左圖所示。
3. 試著按一下 VPD-173X/173X-64 螢幕上面的圖示，VPD-173X/173X-64
會切到其他的頁面。
5 硬體安裝
VPD-173X/173X-64 的面板安裝 (Panel Mounting)
於上下方的通風口，插入面板固定鋁夾
使用
M4 x 15L 螺
絲釘，鎖緊固定面
板及鋁夾