iCreation CL-3223 User manual

CL-3223
USER’S MANUAL
Wireless Digital
Video Doorbell
Shaker jack

Congratulations
Safety Precautions
Prior To Use
...on purchasing our high quality product. Please read the
manual carefully before installing your system and follow
all of the directions to ensure proper installation.
To reduce the risk of electrical shock and injury, please follow
these basic safety precautions before using the product.
1.Carefully read and observe the instructions in this manual.
2.Follow all warnings marked on the unit.
3.
roduct from the wall outlet before cleaning, then
use a damp cloth to wipe. Do not use liquid or aerosol
cleaners.
5.Do not place objects on the line cord that may cause
damage.
7.Pay attention to the polarity of the batteries, insert the
rechargeable batteries in accordance with polarity symbols
(this instruction is found in the installing batteries section.)
8
9.Use only in the described manner.
10.Stop using if it becomes damaged.
The time and date must be reset whenever batteries are
replaced.
4.Unplug this p
6.Placing the Outdoor Station near metal can affect the range
and signal quality to the Receiver. Test before mounting.
.Keep out of reach of children.
31
Shaker jack

Supports up to 4 Outdoor
Wide angle lens and LED for night vision
Remote door opening ( Optional)
DIY installation to save high labor cost
Stations(sold separately)
Long standby doorbell (battery life up to 2 years or connect
with DC+12V)
Water-proof outdoor station IP55
Microphone and speakerphone
Brightness and audio volume are adjustable
Crystal clear sound quality
PIR Motion Sensor
Shaker function(Optional)
Zooming
Replay key
3.5'' (320x240) QVGA LCD display
Video resolution: 320 x 240, with 25 frames per second
Transmitting distance : with up to 200m range out of doors
Transmitting distance : with up to 50m range indoors
Introduction
2
? Design and specifications are subject to change without notice.
Receiver
Receiving Frequency Range 2.400GHz～2.4835GHz
Monitor 3.5''Color LCD
Data Rate 2.0Mbps
Receiving Sensitivity -90dBm
Demodulation Type GFSK
Resolution 320×240(RGB)
Transmitting Power 19dBm(TYP)
Power Requirement Ni-MH 3.6V,800mAh
Power Consumption
Operating Temperature -10℃ ～40℃
Operating Humidity 0%～85%RH
No. of outdoor stations
supported Max.4
Item Detail
Technical Specification
25
400mA Max
Shaker jack

Once you have unpacked your product, make sure that all the
parts shown below are available. If any pieces are missing or
broken, please promptly call your dealer.
User’s Manual
Rain cover
Unpacking
3
Receiver
Charger Outdoor station
Adapter
(6V, 300mA)
Screws
Ni-MH battery pack
Rechargeable
CL-3223
USER’S MANUAL
Technical Specification
Outdoor station
Transmit Frequency Range 2.400GHz～2.4835GHz
Data Rate 2.0Mbps
Transmitting Power 19dBm (TYP)
Modulation Type GFSK
Transmitting Distance Outdoor:200m, Indoor:50m
Image Sensor Type
Effective Pixels H:320 V:240
Image Processing Motion JPEG
Image Resolution / Frame Rate H:320 V :240 / 25fps
White Balance Auto
Lens
Viewing Angle (Diagonal)
Minimum Illumination 1 LUX (without LED illumination)
LED 6 LEDs
Power Requirement
DC+12V / 6×LR6(AA) 1.5V alkaline batteries
Power Consumption 500mA Max (cells),
400mA Max (+12V DC)
Operating Temperature -30℃ ～40℃
Operating Humidity 0% 85%RH～
Item Detail
24
2.1mm/F2.6mm
135°
1/4 Color CMOS Image Sensor″
Shaker jack

Layout
Outdoor Station
4
LED lights
23
Engineering Mode
1.Press and hold the and about 5
seconds in standby mode, then the display will show as follows:
2.After 5 seconds, it will exit automatically.
at the same time
1.press and hold the and at the same time about 5
seconds in standby mode, then the display will show as
follows:
2.Press Left or Right to select the Outdoor station.
3.Press Up or Down to select the unlock time(1-
25 are selectable), then press the Right soft key to
confirm, the display will show OK.
4.After 5 seconds, it will exit automatically.
Delete a Registered Outdoor Station
Change the Unlock Time
PIR
Call button
Speaker
Camera
Sensor light
Microphone
Shaker jack

5
Receiver
Charger
Charge pins
Antenna Locking Switch
Antenna
Speaker
Charging pins
LCD display
Right Soft/
Unlock/
Replay key
Left Soft key
Accept key Power/
End key
Manual Snap
Monitor key
/
Navigation key
Microphone
Charge indicator
Battery
compartment cover
22
Reset to Factory Default
Note:
If you reset the receiver to the factory default, all of the
settings will return to the factory default
any custom settings made.
and you will lose
1.Press beneath to display the main menu items.
2.Press Up or Down to choose , then press
beneath Select.
3.Press Up or Down to choose YES or NO to enable
or disable the function.
4.Press beneath Select to save the settings.
Result: After resetting, the receiver will return to standby mode.
Menu
Shaker jack(Optional)
Menu Functions (continued)
Shaker jack

6
The rechargeable Ni-MH batteries (AAA size,
come with your receiver. Install the batteries before use.
3.6V, 800mAh)
1.
Receiver
2.
3. To replace the battery cover, slide the
cover up until it snaps in place.
The batteries need to be replaced if they don't
r e c o v e r t h e i r f u l l s t o r a g e c a p a c i t y a f t e r
recharging.
When replacing the batteries, always use a good
quality Ni-MH battery.
Notes:
Installing Batteries
Plug the Rechargeable Ni-MH
battery pack into the battery
compartment.
21
You can save or delete the recorded s under this menu.
The outdoor station's number will also be displayed on the upper
left of the photo.
1.Press beneath Menu to display the main menu items.
2.Press Up or Down to choose , then press
beneath Select.
3.Press Left or Right to browse pictures.
4.If you want to delete a photo, use Left or Right to
choose the photo you want to delete, then press the
beneath Del. The display will show Delete?, press
beneath Yes to confirm. Then the LCD will show the next
photo.
5.Press beneath Back to return to the previous menu.
photo
Snap Show
Menu Functions (continued)
Note:
Also, you can press key to play the photos in the
standby mode.
Shaker jack

7
Important Note: Before initial operation, YOU SHOULD
FULLY CHARGE THE RECEIVER for
about 15 hours.
To charge the , you should place it on the charger.
The charge indicator will light during charging.
receiver
Charging Receiver
Outdoor station
Install six LR6(AA) 1.5V alkaline batteries (not supplied) into the
battery compartment, matching correct polarity(+,-).
Reversing the orientation may damage the outdoor
station.
When replacing the batteries, always use good quality
alkaline batteries.
Notes:
Installation Instruction
Receiver
Connect the modular end of the AC
power adapter to the power jack of
the charger, then plug the AC adapter
into a standard AC wall outlet.
To AC wall outlet
With Auto Snap On, the camera will take photos
automatically.
If you have unreviewed photos, the backlight on the key will
be on.
of visitor
Menu Functions (continued)
Notes:
During a conversation, save a photo by pressing the
Snap key.
While monitoring an Outdoor Station, a photo can be
saved by pressing the Snap key.
Up to 50 photos can be stored. When full, the oldest
photo will be deleted when a new one is taken.
Snap Setting
The unique Snap Shot function records up to 50 photos of any
visitors whether you are there or not. To get Auto Snap, set it up
in the receiver as follows.
1.Press beneath Menu to display the main menu items.
2.Press Up or Down to choose ,then press
beneath Select.
3.Press Up or Down to choose 1 Photo, 2 Photos,
3 Photos and Off to enable or disable the function.
4.Press beneath Select to save the settings and return to
the previous menu. 20
Shaker jack

8
Menu Functions (continued)
19
Receiver
If you prefer to mount the on the wall:
a. Install the two self-tapping screws at a distance of 45mm from
each other and located on a horizontal line.
b.
receiver
Slowly slide the unit down until it snaps into place.
Outdoor station
1.Choose a proper location for the outdoor station. Be sure to
consider the average height of visitors.
2.Align the rain cover and screws with the holes in the wall.
3.Install the outdoor station into the rain cover. Please refer to
picture 3 below.
4.Drill holes and mount. Wall anchors are provided if needed.
1234
Brightness
There are 9 levels to adjust brightness on the Receiver.
1. If no video call is active, press Up or Down to
adjust the brightness.
2. If a call is in progress, press beneath Menu to display the
main menu items.
3.Press or to choose , then press
beneath Select.
4.Press Left or Right to select the light level that you
like. Each time you press Left or Right , the receiver
displays with the selected light level.
5.Press beneath Back to save the settings and return to the
previous menu.
Up Down
a
Key Tone
Receiver key tone can be silenced.
1.Press beneath to display the main menu items.
2.Press Up or Down to choose ,then press
beneath Select.
3.Press Up or Down to choose On or Off to enable
or disable the function.
4.Press beneath Select to save the settings and return to
the previous menu.
Menu
a
Shaker jack

9
1
Notes:
18
Menu Functions (continued)
Notes:
1. Avoid locating near electrical appliances, TV or a cordless
phone for best signal performance.
2. Ideal location is a central place with minimal obstructions.
3. A pop up antenna is available to enhance the signal should it
be needed.
2
3
Volume
There are 9 levels to adjust call volume.
1. If no video call is active, press Left or Right to adjust
the volume.
2. If a call is in progress, press beneath Menu to display the
main menu items.
3.Press or to choose then press
beneath Select.
4.Press Left or Right to select the volume. Each time
you press Left or Right , the receiver sounds with
the selected volume.
5.Press beneath Back to save the settings and return to the
previous menu.
Up Down ,
Shaker jack