IDEAL INDUSTRIES NaviTEK II User manual

NaviTEK II
User Guide
151810 issue 1
www.vemco.pl

The information contained in this document is the property of IDEAL INDUSTRIES Ltd. and is
supplied without liability for errors and omissions. No part of this document may be reproduced or
used except as authorized by contract or other written permission from IDEAL INDUSTRIES Ltd.
The copyright and all restrictions on reproduction and use apply to all media in which this information
may be placed.
IDEAL INDUSTRIES Ltd. pursues a policy of continual product improvement and reserves the right
to alter without notice the specification, design, price or conditions of supply of any product or
service.
All rights reserved
Publication ref: 151810 Issue 1
Issue 1 - 03/12
Applies to software revision 1.0.0 onwards
IDEAL INDUSTRIES LTD.
Stokenchurch House
Oxford Road
Stokenchurch
High Wycombe
Buckinghamshire
HP14 3SX UK
UK:
[phone]
[email protected]om
France:
[phone]
[e-mail]
Deutschland:
[phone]
[e-mail]
International:
[phone]
[email protected]om
www.vemco.pl

NaviTEK II 151810 Iss 1
User Guide Page 3
Care of your NaviTEK II............................................................................................................................4
Final Disposal...........................................................................................................................................4
Safety........................................................................................................................................................4
Connector Safety...................................................................................................................................4
Power........................................................................................................................................................5
Power Module Management..................................................................................................................5
Power Module Recharging.....................................................................................................................5
Battery Pack...........................................................................................................................................5
Switching ON and OFF..........................................................................................................................6
Power Saving.........................................................................................................................................6
Master Reset..........................................................................................................................................6
Replaceable insert –RJ-45 socket...........................................................................................................7
Functional overview..................................................................................................................................7
Handset Controls, Indicators and Ports....................................................................................................8
Menu Navigation.......................................................................................................................................9
Soft Keys ..................................................................................................................................................9
Data entry.................................................................................................................................................9
Getting started........................................................................................................................................10
Modes of Operation................................................................................................................................10
Cable....................................................................................................................................................10
Ethernet................................................................................................................................................10
Ports .......................................................................................................................................................11
Setup ......................................................................................................................................................12
Setup menu descriptions........................................................................................................................13
Supported SFP Transceivers .................................................................................................................16
Tests - General.......................................................................................................................................17
Tests menu description –Cable mode...................................................................................................18
Wiremap...............................................................................................................................................18
Tone.....................................................................................................................................................21
Auto test...............................................................................................................................................21
Tests menu description –Ethernet mode...............................................................................................22
Blink .....................................................................................................................................................22
Loop.....................................................................................................................................................22
Netscan................................................................................................................................................22
Ping4 and Ping6...................................................................................................................................23
TRoute4 and TRoute6 .........................................................................................................................23
802.1x Certificates..................................................................................................................................24
Statistics .................................................................................................................................................25
Stats menu description ........................................................................................................................25
Jobs........................................................................................................................................................27
Using the Jobs menu...........................................................................................................................28
Change the active Job.........................................................................................................................28
Managing Jobs.....................................................................................................................................29
Generating Reports................................................................................................................................30
Specifications - NaviTEK II.....................................................................................................................31
Glossary, abbreviations and acronyms ..................................................................................................43
www.vemco.pl

151810 Iss 1 NaviTEK II
Page 4 User Guide
Although light and portable, NaviTEK II is robust and has been designed to operate in a protected outdoor
working environment.
To ensure reliable operation:
Avoid very high or low temperatures - NaviTEK II is designed to operate between 0°C and +40°C,
although you should only charge the battery between +10°C and +30°C. You can store the unit
safely between -20°C and +70°C.
To avoid damage, we recommend that you keep NaviTEK II in its carrying case when you are not
using it.
Do not use solvents, strong detergents or abrasive materials to clean NaviTEK II. Use only
cleaning agents approved for use on ABS and polycarbonate plastics.
When your NaviTEK II has reached the end of its life you must dispose of the complete unit in accordance
with local environmental regulations.
When using NaviTEK II, always take basic safety precautions to reduce the risk of fire, electric shock and
injury to persons. These include the following:
When connecting to the line, special care must be taken as high voltages may be present on the
line and there may be a danger of electrocution.
Avoid using the tester during an electrical storm - there is a remote risk of electric shock by
lightning.
Use only the mains electricity adaptor supplied with your NaviTEK II.
CLASS 1 LASER PRODUCT. Light output from the fiber optic port can damage eyesight even though it is
invisible. Never stare into open optical ports or the end of a fiber to see if light is coming out.
Connector Safety
The following connectors conform to EN60950 SELV safety status:
RJ-45 Ethernet port.
USB port.
DC inlet port.
DO NOT CONNECT ANY TELECOMMUNICATIONS
NETWORK TO ANY OF THE TESTER’S PORTS
www.vemco.pl

NaviTEK II 151810 Iss 1
User Guide Page 5
All models of NaviTEK II can be powered from:
A rechargeable power module,
Directly from power connected to the DC inlet built in to the power module.
From an alkaline battery pack.
The type of module or pack supplied as standard depends on the model purchased.
Power Module Management
A fully charged power module will support up to five hours of heavy, continuous use. For maximum life of
the power module it is recommended to discharge it fully and then recharge it fully at least once a month.
The power module is not user-serviceable. When it has reached the end of its life, contact your local
IDEAL representative for service.
Power Module Recharging
The power module can be fully recharged in three hours with the NaviTEK II switched ON or OFF. To
recharge the power module, connect the supplied power adaptor to the DC inlet. For convenience the
power module may be removed from, or left attached to, the tester for charging. The Power LED next to
the DC inlet glows green to show that the battery is being charged, and flashes green to show that it is not
being charged. The power module’s charge state is indicated at FULL, 2/3, 1/3 and EMPTY by the
graphical power meter shown in the information bar at the top of the display.
Fig 1 Power indications
Battery Pack
The battery pack accepts four replaceable AA alkaline cells. These cells cannot be recharged.
www.vemco.pl

151810 Iss 1 NaviTEK II
Page 6 User Guide
Switching ON and OFF
To switch the tester ON, press and hold the Power button. Wait until the home screen is visible on the
display; the tester is ready for use.
To switch the tester OFF, press and hold the Power for approximately 1/2 second, a shutdown message is
displayed on the screen. The currently stored setup is saved. If the tester does not switch OFF within five
seconds, see Master Reset.
Power Saving
Power saving preferences are selected from SETUP>SYSTEM>PREF. Auto off can be Disabled (tester
remains ON indefinitely), or set to switch the tester OFF after three, 10 or 30 minutes of inactivity. The
backlight can be set to Always On, or to dim to 50% brightness after three minutes of inactivity. Note that
when mains power is connected the display is always on full brightness and the tester remains ON
indefinitely.
Master Reset
In the unlikely event of a system lock-up which prevents the tester from being switched OFF, it may be
necessary to perform a master reset. This will not delete any stored data.
Remove the power module or battery pack to access a small aperture in the NaviTEK II (Fig 2).
Insert a paper clip into the reset hole and press the internal reset switch.
Fig 2
Replace the power module or battery pack.
www.vemco.pl

NaviTEK II 151810 Iss 1
User Guide Page 7
To replace a damaged or worn RJ-45 socket insert proceed as follows:
Equipment required: Kit, IDEAL part number 150058 –includes Tool x1 and Replacement Insert x10.
Switch the NaviTEK II OFF.
Connect the tool to the socket insert that is
to be replaced.
Note the orientation of the insert within the
socket and carefully remove it using the tool.
Install the new insert to the socket using
your fingers.
The NaviTEK II range offers three models. The available functions are listed below. The information
throughout this publication details the functions available to NaviTEK II PRO. Please check this table to
confirm the functionality of your tester.
LAN testing over copper



IPv4



IPv6



Advanced Wiremap



PoE detection



Tone Generator



Ping test



Traceroute test



Hub blink



VLAN support


Netscan


Traffic utilization


Results storage & export


802.1x security

LAN testing over optical fiber

Loopback mode (copper & fiber)

www.vemco.pl

151810 Iss 1 NaviTEK II
Page 8 User Guide
Fig 3
1
RJ 45 port
9
Function keys F1 to F3
2
RJ 45 activity LED
10
Escape key
3
RJ 45 link LED
11
Cursor and ENTER keys
41
Optical port (SFP)
12
ON/OFF button
51
Optical activity LED
132
Power module
61
Optical link LED
142
Charger LED
7
USB port
152
DC in connector
8
LCD color display
16
Autotest button
1 Fig 3 items 4, 5 & 6 –NaviTEK II PRO only.
2 Fig 3 item 13 shows optional power module.
www.vemco.pl

NaviTEK II 151810 Iss 1
User Guide Page 9
Cursor and ENTER keys. The arrowed cursor keys are
intuitively marked to move the highlighted field between all
menu icons, settings fields and drop-down menus1that
appear on the display. ENTER selects the currently
highlighted option.
Escape key. Returns to previous screen or hides the
options of a drop-down menu. Note that when a value in a
settings field is changed, if the Escape key is pressed before
the soft key ‘APPLY’, the value will not be stored.
Autotest key. Immediately runs pre-stored tests. A new
tester will have factory stored tests in memory. These are
easily changed using the SETUP menu.
Function keys. F1 to F3 are to select the corresponding
soft keys at the lower edge of the display.
Fig 4
The soft keys appear along the bottom edge of the display. Their function changes and is dependent on
the screen currently shown on the display.
Fig 5
When you navigate to and select a field that requires a
value or text to be entered, such as a customer’s name or a
URL, a QWERTY keyboard will be shown on the display
(Fig 5). All data is entered using the QWERTY keyboard.
Move the key that is highlighted on the keyboard using the
tester’s cursor keys. ENTER selects the currently
highlighted key which will now appear in the text window
directly above the keyboard. Key stroke errors are
corrected using the backspace key ( <− ). Press the UP
cursor key to move the cursor into the text window for
editing.
Press the QWERTY keyboard’s SHIFT key to change the
display from lower to upper case. Press SHIFT a second
time to display symbols and punctuation characters.
When the text or value has been entered, press the soft key
OK (F1). The display will return to the previous screen
which is now populated with the required data. You must
press the soft key APPLY to save the changes.
1 Only NaviTEK II PLUS and PRO support drop-down menus. For NaviTEK II, to select a value from a
field that offers a list of values, use the LEFT and RIGHT cursor keys. To move to the previous or next
field on the screen use the UP or DOWN cursor keys. ENTER will move to the next field. With all models,
press the soft key APPLY (F2) to save changes.
www.vemco.pl

151810 Iss 1 NaviTEK II
Page 10 User Guide
Press the soft key DETECT (F1) and the tester will determine the mode of operation dependent on the
services detected.
The modes of operation that follow are available:
NaviTEK II has two fundamental modes of operation –
Cable
When the tester is connected to a copper cable,
with or without an active remote, press the soft
key DETECT (F1) to display all options
available from the Cable mode screen (Fig 6).
When an active remote is connected it will be
shown on screen and its identification number
displayed. For a full description of these
options, see - Tests menu description –Cable
mode.
Fig 6
Ethernet
Fig 7
When the tester is connected to a network/device,
using either copper or fiber cable, press the soft key
DETECT (F1), to display all options available from
the Ethernet mode screen (Fig 7). For a full
description of these options see –Tests menu
description –Ethernet mode.
The detected services are PoE (802.3af/at. Not
Cisco pre-standard), ISDN S, PBX and Unknown.
The IPv4 and IPv6 addresses assigned to the tester
are displayed (when available).
www.vemco.pl