Features:
Rugged, compact, metal construction for ultimate roadworthiness, long life,
and reliability.
Tests cables with all types of combinations of the following connectors:
• 3.5mm and 6.35mm TRS
• balanced XLR (M/F)
• Phono/RCA
• banana plug
• 4-pin and 8-pin-Speakon
• 3-pin, 5-pin, 7-pin, 8-pin DIN
• 7-pin and 8-pin CAT-5
Also provides checks of internal battery voltage and earth / ground status.
MCT-20 Cable Tester
Thomann
GmbH
•
Hans-Thomann-Straße
1
•
96138
Burgebrach
•
www.thomann.de
•
inf
[email protected] DocID: 223637_29.09.2015Conguration:
6,35 mm mono jack (TS) to 6,35 mm mono jack.
1 sleeve to 1 sleeve, 3 ring
2 tip to 2 tip
3 ring to 1 sleeve, 3 ring
(shorted with sleeve)
6,35 mm jack (TRS) to 6,35 mm jack (TRS)
1 sleeve to 1 sleeve
2 tip to 2 tip
3 ring to 3 ring
XLR balanced to XLR balanced
pin 1 to pin 1
pin 2 to pin 2
pin 3 to pin 3
XLR unbalanced to XLR unbalanced
pin 1 to pin 1, pin 3
pin 2 to pin 2
pin 3 to pin 1, pin 3
6,35 mm mono jack (TS) to XLR unbalanced
1 sleeve to pin 1, pin 3
2 tip to pin 2
3 ring to pin 1, pin 3 (shorted with sleeve)
6,35 mm jack (TRS) to XLR balanced
1 sleeve to pin 1
2 tip to pin 2
3 ring to pin 3
Cable Test:
At rst, turn the rotary switch fully clockwise to test the battery strength.
The battery LED will light bright green if the internal battery is fully char-
ged. After changing the battery, slide the battery compartment completely
in and push the cover against the arrow direction down until it clicks into
place.
Then plug one end of the cable into the appropriate jack on the left side pa-
nel of the cable tester. Plug the other end of the cable into the appropriate
jack on the right side panel. Set the rotary switch to ‘1’ to test the connecti-
on of contact 1 on the plug inserted into the left side panel.
If there is a connection, the Green LED will light below ‘1’ and a Yellow LED
will light above each contact on the right side plug connected to‘1’ on the
left side plug. Use the charts below to verify proper cable connections.
If no LED lights then there is no connection and the left side contact ‘1’ is
‘oating’due to design or an ‘open’ in the cable. Set the rotary switch to ‘2’
to test contact 2, and so on, until all contacts have been checked.
If the Ground LED lights then there is a connection between the correspon-
ding contacts and the chassis.
To test the cable with a banana plug, just plug each end of the cable into
the banana jacks. The unit will beep a tone if there is a connection between
the plugs. These banana jacks can also be used for continuity tests using
two probe leads.
Plug conguration:
jack
1 = sleeve
2 = tip
3 = ring
Speakon
1 = – 1
2 = +1
3 = – 2
4 = +2
5 = – 3
6 = +3
7 = – 4
8 = +4
Phono (chinch)
1 = screen
2 = hot
For the transport and protective packaging, environmentally friendly mate-
rials have been chosen that can be supplied to normal recycling. Ensure that
plastic bags, packaging, etc. are properly disposed of. Do not just dispose of
these materials with your normal household waste, but make sure that they
are collected for recycling. Please follow the notes and markings on the packaging.
This product is subject to the European Waste Electrical and Electronic
Equipment Directive (WEEE) in its currently valid version. Do not dispose of
your old device with your normal household waste. Dispose of this product
through an approved waste disposal rm or through your local waste facility.
Comply with the rules and regulations that apply in your country. If in doubt,
consult your local waste disposal facility.
