Triplett CTX200 User manual

CTX200 RJ45/Coax Cable
Tester
USER MANUAL
99 Washington Street
Melrose, MA 02176
Phone [phone]
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com

Introduction
Congratulations on your purchase the CTX200 RJ45/Coax Cable Tester. The
system consists of a Main Tester and a Remote Terminator and Preforms the
following tests: Continuity, Open & Short Circuits, Wire Crossed (Reverse and
Split) Tests CAT3, 5, 5e, 6, 6A, & 7 Ethernet Cables to TIA568 Specs • Tests
COAX Cables • Locates Cables*
WARNING!!!
DO NOT USE ON LIVE CIRCUITS!!
**NOTE: <5V/20mA rating**
Features
 Tests and tones both RJ45-CAT5/6 and coax cables.
 Ruggedized for field use. Small and easy to carry.

 PASS/FAIL results appear in one second.
 Each pair’s status is highlighted.
 Complete TIA568 test performed. Continuity, opens / shorts, reversals
and split pairs.


 Auto-off (12 seconds) to conserve battery life.
 Low battery indicator.
 (1) 9V Battery and Pouch included.
Quick Start: Cable Testing

Purpose

Ethernet cables have 4 pairs of wires (”twisted pairs”). It is important that the pairs
correctly go to connector pins 1,2 ; 3,6 ; 4,5 ; and 7,8. The Pocket CAT tests for
the proper pairing and if there is an error it will report it to you (”split pairs”)
Connecting cables to the Tester
Installed cables: Connect the Main unit to the wall jack, then connect the remote
to the patch panel or far-end wall jack
Patch cables: Attach the Main unit and Remote directly to the cable ends.
Power ON and Test
Press the ON button. Press again to begin test. When the PASS/FAIL LEDs light,
press the FAULT CHECK button to isolate any problems to an individual pair.
Coax Testing Coax is displayed using the 4/5 LEDs. The coax remote is in the
pouch.
Quick Start: Cable Locating with Tone
Purpose

Tone is used to locate a cable’s far end. A tone is placed on the cable’s
“near end” by the CTX200 Main unit. The probe locates the tone at the far
end of the cable. NOTE: Requires
Connecting cables to the Tester
Plug the cable into the tester’s Main unit.
Power ON and Tone:
Press the ON button. Hold the TONE button for 7 secs to turn ON the tone.
Press the TONE button repeatedly to select the pair you wish to tone. The
tone is loudest when you select the entire cable (including the shield).
Connecting the Cable Tester
Testing patch cables
Slide Remote Connector out from base of Pocket CAT, then connect one end of the cable
to the Remote Connector, and the other end to the Pocket CAT.
Testing installed cables
Slide Remote Connector out from base of Pocket CAT, then connect the far end of the
cable to the Remote Connector, and the other end to the Pocket CAT. NOTE: The Remote
Connector for COAX testing is located in the pouch..

Faceplate POCKET CAT FACEPLATE
Pass/Fail
Indicator
Pair/Shield
Tested
(Coax uses 4/5)
Press to test all pairs
automatically.
Press to test pairs individually. Hold 7 second for Tone and Press again to select pair.
Remote Connector: Push or Slide to Remove.
Testing RJ45 and Coax Cables
Power ON and TEST: Press the ON button. Press again to commence the test. The bright, blue
PASS LED indicates the cable has passed. If the FAIL LED lights, press the FAULT CHECK button
to isolate problems to an individual pair. See back for more examples.
OPEN: A wire is disconnected.
SHORT: A wire makes contact with
another wire.
CROSS (REVERSAL): a twisted pair
gets flipped on one side of the cable
SPLIT: One wire from each of two
different pairs gets swapped on both
ends of the cable.

Testing Examples: Coax
The Pocket CAT uses LED 4&5 to display the status of a coax cable test.. Connect the near end
of the cable to the BNC connector. Connect the far end to the coax terminator (pouch).
Good Cable:
LEDs
ON
OFF
BLINK
Short in Cable:
LEDs
ON
OFF
BLINK

Testing Examples: Ethernet
Ethernet cables have 4 pairs of wires (”twisted pairs”). It is important that the
pairs correctly go to connector pins 1,2; 3,6; 4,5; and 7,8. The tester tests for the
proper pairing and if there is an error it will report it to you. The follow-ing examples
are based on EIA/TIA 568B (the most popular ethernet wiring standard).
Good Cable:

Open on Pair 1-2:
Split Pairs 1-2 &3-6:
Short on Pair 3-6:

Crossed Pairs 4-5 & 7-8:
Warranty Information
Triplett / Jewell Instruments extends the following warranty to the original purchaser of
these goods for use. Triplett warrants to the original purchaser for use that the products sold
by it will be free from defects in workmanship and material for a period of (1) one year from
the date of purchase. This warranty does not apply to any of our products which have been
repaired or altered by unauthorized persons in any way or purchased from unauthorized
distributors so as, in our sole judgment, to injure their stability or reliability, or which have
been subject to misuse, abuse, misapplication, negligence, accident or which have had the
serial numbers altered, defaced, or removed. Accessories, including batteries are not
covered by this warranty Copyright ©2019 Triplett
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com