IDEAL INDUSTRIES SignalTEK II User manual

SignalTEK II
User Guide
156810 issue 1
www.vemco.pl

The information contained in this document is the property of IDEAL INDUSTRIES Ltd. and is
supplied without liability for errors and omissions. No part of this document may be reproduced or
used except as authorized by contract or other written permission from IDEAL INDUSTRIES Ltd.
The copyright and all restrictions on reproduction and use apply to all media in which this information
may be placed.
IDEAL INDUSTRIES Ltd. pursues a policy of continual product improvement and reserves the right
to alter without notice the specification, design, price or conditions of supply of any product or
service.
All rights reserved
Publication ref: 156810 Issue 1
Issue 1 - 04/12
(Applies to software revision 1.0.0 onwards)
IDEAL INDUSTRIES LTD.
Stokenchurch House
Oxford Road
Stokenchurch
High Wycombe
Buckinghamshire
HP14 3SX UK
UK:
[phone]
[email protected]om
France:
[phone]
[e-mail]
Deutschland:
[phone]
[e-mail]
International:
[phone]
[email protected]om
www.vemco.pl

SignalTEK II 156810 Iss 1
User Guide Page 3
Introduction...............................................................................................................................................4
Care of your SignalTEK II.........................................................................................................................5
Final Disposal...........................................................................................................................................5
Safety Information ....................................................................................................................................5
Connector Safety...................................................................................................................................5
Power........................................................................................................................................................6
Power Module Management..................................................................................................................6
Power Module Recharging.....................................................................................................................6
Battery Pack...........................................................................................................................................6
Switching ON and OFF..........................................................................................................................7
Power Saving.........................................................................................................................................7
Master Reset..........................................................................................................................................7
Handset Controls, Indicators and Ports....................................................................................................8
Menu Navigation.......................................................................................................................................9
Soft Keys ..................................................................................................................................................9
Data entry.................................................................................................................................................9
Getting started........................................................................................................................................10
Modes of Operation................................................................................................................................10
Cable....................................................................................................................................................10
Ethernet................................................................................................................................................10
Ports .......................................................................................................................................................12
Replaceable insert –RJ-45 socket......................................................................................................12
Setup ......................................................................................................................................................13
Setup menu descriptions........................................................................................................................14
Supported SFP Transceivers .................................................................................................................17
Tests modes...........................................................................................................................................18
Cable mode..........................................................................................................................................18
Ethernet mode .....................................................................................................................................18
Tests –run, setup and save...................................................................................................................19
Tests menu description –Cable mode...................................................................................................20
Wiremap...............................................................................................................................................20
Tone.....................................................................................................................................................23
Autotest................................................................................................................................................23
Tests menu description –Ethernet mode...............................................................................................24
Cable performance ..............................................................................................................................24
PoE ......................................................................................................................................................25
Blink .....................................................................................................................................................25
Ping4 and Ping6...................................................................................................................................26
TRoute4 and TRoute6 .........................................................................................................................26
Netscan................................................................................................................................................27
VoIP .....................................................................................................................................................28
Web......................................................................................................................................................29
Video....................................................................................................................................................29
CCTV ...................................................................................................................................................29
Jobs........................................................................................................................................................30
Using the Jobs menu...........................................................................................................................31
Change the active Job.........................................................................................................................31
Managing Jobs.....................................................................................................................................32
Generating Reports................................................................................................................................33
Specifications - SignalTEK II..................................................................................................................34
Near-End Unit ......................................................................................................................................34
Remote Unit.........................................................................................................................................49
Glossary, abbreviations and acronyms ..................................................................................................54
www.vemco.pl

156810 Iss 1 SignalTEK II
Page 4 User Guide
SignalTEK II comprises two hand-held units and a set of standard accessories all held in a semi-rigid
case.
Two models are available, SignalTEK II and SignalTEK II FO. Both models are capable of performing the
same range of tests. SignalTEK II has RJ45 connectivity; SignalTEK II FO has both RJ45 and Fiber
connectivity.
Fig 1 SignalTEK II components
The Near-End unit is the terminal from where all tests are run and stored. The Remote Unit is a loopback
terminal that enables performance testing. The Near-End Unit and Remote Unit are paired. When they
are both connected to the same network, the Near-End Unit will find the Remote Unit that it is uniquely
paired with, and not any other SignalTEK II Remote Unit that may be connected to the same network.
The Near-End unit may be used as a stand-alone device for wiremap testing copper network cables.
When both units are directly connected by a cable, wiremap and cable performance tests can be run.
When the Near-End Unit is connected to a network, it can be used to carry out a range of IP tests. When
both the Near-End and Remote Unit are connected to an active network, both IP tests and network
performance tests are possible.
This manual describes the operation and functions of the SignalTEK II FO.If you are using SignalTEK II
please disregard all references to fiber optics.
www.vemco.pl

SignalTEK II 156810 Iss 1
User Guide Page 5
Although light and portable, the SignalTEK II units are robust and have been designed to operate in a
protected outdoor working environment.
To ensure reliable operation:
Avoid very high or low temperatures - SignalTEK II is designed to operate between 0°C and +40°C,
although you should only charge the batteries between +10°C and +30°C. You can store the unit
safely between -20°C and +70°C.
To avoid damage, when they are not in use we recommend that you keep both SignalTEK II units
in their carrying case.
Do not use solvents, strong detergents or abrasive materials to clean SignalTEK II. Use only
cleaning agents approved for use on ABS and polycarbonate plastics.
When your SignalTEK II has reached the end of its life you must dispose of both complete units in
accordance with local environmental regulations.
When using SignalTEK II, always take basic safety precautions to reduce the risk of fire, electric shock
and injury to persons. These include the following:
When connecting to the line, special care must be taken as high voltages may be present on the
line and there may be a danger of electrocution.
Avoid using SignalTEK II during an electrical storm - there is a remote risk of electric shock by
lightning.
Use only the mains electricity adaptor supplied with your SignalTEK II.
CLASS 1 LASER PRODUCT. Light output from the fiber optic port can damage eyesight even though it is
invisible. Never stare into open optical ports or the end of a fiber to see if light is coming out.
Connector Safety
The following connectors conform to EN60950 SELV safety status:
RJ-45 Ethernet port.
USB port.
DC inlet port.
DO NOT CONNECT ANY TELECOMMUNICATIONS
NETWORK TO ANY OF THE TESTER’S PORTS
www.vemco.pl

156810 Iss 1 SignalTEK II
Page 6 User Guide
SignalTEK II can be powered from:
A rechargeable power module,
Directly from power connected to the DC inlet built in to the power module.
From an alkaline battery pack.
The type of module or pack supplied as standard depends on the model purchased.
Power Module Management
A fully charged power module will support up to five hours of heavy, continuous use. For maximum life of
the power module it is recommended to discharge it fully and then recharge it fully at least once a month.
The power module is not user-serviceable. When it has reached the end of its life, contact your local
IDEAL representative for service.
Power Module Recharging
The power module can be fully recharged in three hours with the SignalTEK II (either unit) switched ON or
OFF. To recharge the power module, connect the supplied power adaptor to the DC inlet. For
convenience the power module may be removed from, or left attached to, the unit for charging. The
Power LED next to the DC inlet glows green to show that the battery is being charged, and flashes green
to show that it is not being charged.
The Near-End Unit’s power module charge state is indicated at FULL, 2/3, 1/3 and EMPTY by the
graphical power meter shown in the display’s information bar at the top of its LCD display.
Fig 2 Power indications
The Remote Unit’s power module charge state is indicated by an LED directly below the Autotest key.
LED indications are:
Green
Power ON. Battery level sufficient for use
Red
Power ON. Battery charge level low but still operational
Off
Power OFF
Battery Pack
Battery packs accept four replaceable AA alkaline cells. These cells cannot be recharged.
www.vemco.pl

SignalTEK II 156810 Iss 1
User Guide Page 7
Switching ON and OFF
To switch ON the units, press the ON/OFF button.A splash screen showing the IDEAL logo and model
identity is shown on the display. The Near-End unit attempts to detect a network and the Remote Unit.
The home screen is then shown on the display. SignalTEK II is ready for use.
To switch OFF either unit, press and hold the Power button for approximately 1/2 second, a shutdown
message is displayed on the screen. The currently stored setup is saved. If the unit does not switch OFF
within five seconds, see Master Reset.Always switch OFF the unit before removing the battery pack or
power module.
Power Saving
Near-End Unit. Power saving preferences are selected from SETUP>SYSTEM>PREF. Auto Off can be
Disabled (unit remains ON indefinitely), or set to switch the unit OFF after three, 10 or 30 minutes of
inactivity. The backlight can be set to Always On, or to dim to 50% brightness after three minutes of
inactivity. Note that when mains power is connected the display is always on full brightness and the unit
remains ON indefinitely.
Remote Unit. The remote unit remains ON indefinitely whether on battery or mains power.
Master Reset
In the unlikely event of a system lock-up which prevents the unit from being switched OFF, it may be
necessary to perform a master reset. This will not delete any stored data.
Remove the power module or battery pack to access a small aperture in the SignalTEK II (Fig 3).
Insert a paper clip into the reset hole and press the internal reset switch.
Fig 3
Replace the power module or battery pack.
www.vemco.pl

156810 Iss 1 SignalTEK II
Page 8 User Guide
Fig 4
1
RJ 45 port
9
Function keys F1 to F3
17
Link LED
2
RJ 45 activity LED
10
Escape key
18
Status LED
3
RJ 45 link LED
11
Cursor and ENTER keys
19
1000 Mb/s line rate LED
41
Optical port (SFP)
12
ON/OFF button
20
100 Mb/s line rate LED
51
Optical activity LED
132
Power module
21
10 Mb/s line rate LED
61
Optical link LED
142
Charger LED
22
Remote Autotest button
7
USB port
152
DC in connector
23
Power LED
8
LCD color display
16
Autotest button
1 Fig 4 items 4, 5 & 6 –SignalTEK II FO only.
2 Fig 4 item 13 shows optional power module.
Note: The top, bottom and left hand side of both units are identical.
www.vemco.pl

SignalTEK II 156810 Iss 1
User Guide Page 9
Cursor and ENTER keys. The arrowed cursor keys are
intuitively marked to move the highlighted field between all
menu icons, settings fields and drop-down menus that
appear on the display. ENTER selects the currently
highlighted option.
Escape key. Returns to previous screen or hides the
options of a drop-down menu. Note that when a value in a
settings field is changed, if the Escape key is pressed before
the soft key ‘APPLY’, the value will not be stored.
Autotest key. Immediately runs pre-stored range of tests.
The range is easily changed using the SETUP menu. The
Autotest keys on the Near-End and Remote Unit have
identical function.
Function keys. F1 to F3 are to select the corresponding
soft keys at the lower edge of the display.
Fig 5
The soft keys appear along the bottom edge of the display. Their function changes and is dependent on
the screen currently shown on the display.
Fig 6
When you navigate to and select a field that requires a
value or text to be entered, such as a customer’s name or a
URL, a QWERTY keyboard will be shown on the display
(Fig 6). All data is entered using the QWERTY keyboard.
Move the key that is highlighted on the keyboard using the
tester’s cursor keys. ENTER selects the currently
highlighted key which will now appear in the text window
directly above the keyboard. Key stroke errors are
corrected using the backspace key ( <− ). Press the UP
cursor key to move the cursor into the text window for
editing.
Press the QWERTY keyboard’s SHIFT key to change the
display from lower to upper case. Press SHIFT a second
time to display symbols and punctuation characters.
When the text or value has been entered, press the soft key
OK (F1). The display will return to the previous screen
which is now populated with the required data. You must
press the soft key APPLY to save the changes.
www.vemco.pl

156810 Iss 1 SignalTEK II
Page 10 User Guide
Press the soft key DETECT (F1) and the Near-End Unit will determine the mode of operation dependent
on the services detected. The display will show a home screen with one of four connection symbols.
There are two modes of operation, Cable and Ethernet. Cable has one way of connecting, Ethernet has
three.
Cable
Cable mode is used for Wiremap testing and
cable route tracing using the tone generator.
When the Near-End Unit is connected to a
copper cable, with or without an Active Remote,
press the soft key DETECT (F1) to display all
options available from the Cable mode screen.
When an Active Remote is connected it will be
shown on screen (Fig 7) and its identification
number displayed. For a full description of
these options, see Tests menu description –
Cable mode.
Fig 7
Ethernet
Fig 8
Ethernet mode is used for a range of IP and
performance tests. There are three ways to
connect in Ethernet mode:-
(1) When the Near-End Unit and Remote Unit are
directly connected, with copper or fiber cable, press
the soft key DETECT (F1) to detect all options
available (Fig 8). In addition to wiremap tests
(copper), cable performance can be tested and
measured. For a full description of these options
see Tests menu description –Ethernet mode, page
24.
www.vemco.pl