IDEAL Henrad SE 30 FF User manual

Supplied By www.heating spares.co Tel. [phone]

Supplied By www.heating spares.co Tel. [phone]
2
Henrad SE FF - User's

Supplied By www.heating spares.co Tel. [phone]
3
Henrad SE FF - User's
SE FF ( Natural Gas Models Only)
SE 30 FF ...................G.C. Appliance No. 41 387 46
SE 40 FF ...................G.C. Appliance No. 41 387 47
SE 50 FF ...................G.C. Appliance No. 41 387 48
SE 60 FF ...................G.C. Appliance No. 41 387 49
SE 70 FF ...................G.C. Appliance No. 41 387 50
SE 80 FF ...................G.C. Appliance No. 41 387 51
Destination Countries: GB, IE
CAUTION. To avoid the possibility of injury during the installation, servicing or cleaning of
this appliance care should be taken when handling edges of sheet steel components.
PI No: 87AT2

Supplied By www.heating spares.co Tel. [phone]
4
Henrad SE FF - User's
Introduction
The SE FF is a wall mounted, room sealed, super efficient
condensing boiler featuring full sequence automatic spark
ignition and fan assisted combustion.
Duetotheveryhighefficiency,condensate is produced from
the flue gases and this is drained to a suitable disposal
point through the plastic waste pipe at the right lower rear
of the boiler. A condensate 'plume' will also often be visible
at the flue terminal.
Safety
Gas Safety (Installation & Use) Regulations 1994,
amendments 1996 or rules in force.
Inyourowninterest,andthatofsafety,it is the law that
this boiler must be installed by a CORGI registered
installer, in accordance with the above regulations.
It is essential that the instructions in this booklet are
strictly followed, for safe and economical operation of
the boiler.
Electricity Supply
This appliance must be efficiently earthed.
Supply: 230 V ~ 50 Hz. The fusing should be 3A.
Connection must be made in a way that allows complete
isolation of the electrical supply such as a double pole
switch having a 3mm (1/8") contact separation in both
poles, or a plug and socket, serving only the boiler and
system controls. The means of isolation must be
accessible to the user after installation.
To light the boiler
(see illustration on page 5)
Access to the controls is made by swinging the controls pod door
downwards.
If a CH timer is fitted, refer to itsseparate instructions before
continuing.
1. Check that the electrical supply to the boiler is OFF.
2. Ensurethat thegas andwater suppliesto theboiler areOPEN
and external controls are calling for heat.
3. SwitchONthe electricalsupplyto theboilerat themainssupply
socket.
4. Turn the boiler thermostat (B) to position 6.
5. After a short delay the ignition sequence will commence and
the boiler will light.
6. Immediately after ignition the 'Burner On' neon (A) will
illuminate and remain on as long as the boiler is firing.
7. If the boiler does not light at the first ignition attempt (after
about10 seconds), the'Burner On'neon will illuminatebriefly,
go off, and then the ignition sequence will be repeated, for a
total of 5 times.
8. If there is still no ignition the fan will stop and the boiler will
shut down.
9. In this event switch off the electrical supply to the boiler and
consult a CORGI registered installer.
WARNING .
If no frost protection is provided and frost is likely during a short
absence from home, leave the room thermostat and cylinder
thermostat at a reduced setting.
Forlonger periods,theentire systemshouldbe drained- including
the domestic water supply and boiler heat exchanger.
Ifthe systemincludesa frostthermostat then,during coldweather,
the boiler should be turned OFF at the time switch(es) ONLY.
The mains supply should be left switched ON.
To shut down the boiler
1. For short periods
Switch OFF the electrical supply to the boiler.
When heating is again required, restore supply to the boiler.
2. For longer periods
Switch OFF the electrical supply to the boiler or, if a frost
thermostat is fitted, at the time switch.
To relight the boiler
Repeat the procedure detailed in 'To light the boiler'.
Important Notes
!THIS APPLIANCE MUST NOT BE OPERATED WITHOUT
THE CASING CORRECTLY FITTED AND FORMING AN
ADEQUATE SEAL.
!If the boiler is installed in a compartment then the
compartment MUST NOT be used for storage purposes.
!Clearances of 145mm (7 3/4") above, 100mm (4") below,
5mm (1/4") at the sides and 450mm (17 3/4") at the front of
the boiler casing must be allowed for servicing.
!If it is known or suspected that a fault exists on the boiler
then it MUST NOT BE USED until the fault has been
corrected by a CORGI registered installer.

Supplied By www.heating spares.co Tel. [phone]
5
Henrad SE FF - User's
BOILER CONTROLS
LEGEND
A'Burner on' neon
BThermostat knob
CCondensate drain
Escape of gas
Should a gas leak or fault be suspected contact your local gas
supplier without delay.
Do NOT search for gas leaks with a naked flame.
Condensate Drain
The condensate drain must not be modified or blocked.
Blockage of the condensate drain, caused by debris or freezing,
can cause automatic shutdown of the boiler.
If freezing is suspected and the pipe run is accessible an attempt
may be made to free the obstruction by pouring hot water over
the exposed pipe and clearing any blockage from the end of the
pipe.If this failsto remedythe problemthe assistance ofa CORGI
registered installer should be sought.
Cleaning
For normal cleaning simply dust with a dry cloth.
To remove stubborn marks and stains use a damp cloth and mild
detergent.
DO NOT use abrasive cleaning materials.
°C °F
150 120
260 140
366 150
471 160
577 170
682 180
Maintenance
Theappliance shouldbeserviced atleast oncea yearby aCORGI
registered installer.
Control of water temperature
1. Setthe boiler thermostatknob togive therequired temperature
2. The boiler thermostat automatically switches the main burner
OFF and ON to maintain the selected temperature.
Approx. flow temperatures for the boiler thermostat settings are:
Knob Setting Flow Temperature

Supplied By www.heating spares.co Tel. [phone]
6
Henrad SE FF - User's
Caradon Plumbing Ltd pursues a
policyof continuing improvementin the
designand performanceofits products.
The right is therefore reserved to vary
specification without notice.
The code of practice for the installation,
commissioning & servicing of central heating systems
Caradon Plumbing Limited is a member of the
Benchmark initiative and fully supports the aims of the
programme. Benchmark has been introduced to
improve the standards of installation and commissioning
of central heating systems in the UK and to encourage
the regular servicing of all central heating systems to
ensure safety and efficiency.
H enrad Consumer Helpline: 01482 498660
Caradon Plumbing Limited,
P.O. Box 103, National Ave, Kingston upon
Hull, HU5 4JN. Telephone: [phone]
Fax: [phone]. Registration No. London
322 137. Registered Office: National Avenue,
Kingston upon Hull, HU5 4JN. A subsidiary of
Caradon p.l.c August 1999 UIN 153 961 A01

Supplied By www.heating spares.co Tel. [phone]
7
Henrad SE FF - User's
Your feedback
and your chance to win a free boiler
At Henrad we've been leaders in the design and engineering of robust
and reliable boilers for over 90 years. We want to continue as leaders by
listeningtoyoursuggestions forhowtoimproveourboilers and ourservice.
We will be giving away a free boiler for the five best ideas every year (to
be selected by our Technical Director). Please complete this form, using
extra sheets if required, and post it or fax it to us on 01482 498699.
Boiler details
Model / Size (details on control panel door)
Date of Installation
Installer details
Name
Address
Post Code Telephone ( Please include STD code )
How I would improve this boiler: :
My general comments for Henrad:
"
H enrad Consumer Helpline: 01482 498660

Supplied By www.heating spares.co Tel. [phone]
UIN. 153 961 A0
"
Caradon Plumbing Ltd., PO Box 103, National Avenue, Kingston upon Hull, HU5 4JN. Telephone: [phone] Fax: [phone].
H enrad Consumer Helpline: 01482 498660
Further information
If you would like information about Henrad Boilers please complete this
sheet and fax it to us on 01482 498699 or post it to Caradon Plumbing
Limited, PO Box 103, National Avenue, Kingston upon Hull, HU5 4JN.
Installer details
Name
Address
Post Code Telephone ( Please include STD code )
General information required
Please send me details of Henrad Training Courses.
Please arrange for a technical representative to contact me.
Please arrange for me to join an Henrad factory tour.
Range guides required
The Henrad Guide: a specifier's and installer's introduction to the
Henrad domestic boiler range.
The Henrad Householders Guide: to assist the installer when
presenting to his/her customers.
Technical manuals required
The Henrad C FF combi boilers
The Henrad WH FF wall hung boiler
The Henrad WH LX FF deluxe wall hung boiler
The Henrad FS FF floor standing boiler
The Henrad SE FF heat-saving boiler
The Henrad CC FF combi boiler
The Henrad SEC FF super efficiency combi boiler