idesk OROBLANCO 402B User manual

Back Frame G00021/G00038 1A
Item Part Name Part # Qty
Le Arm Cap G00069/G00071 1
1G00070/G00072Right Arm CapO
N
Pivot Lock Bracket
Slide Lock Bracket
Le Arm G00059/G00060 1B
Right Arm G00061/G00062 1C
Seat Pan G00063/G00064 1D
Gas Cylinder G00025 1E
Base G00026 1F
Caster G00008 5G
Hex Wrench G00028 1H
Short Bolt G00030 4J
Long Bolt G00065 2K
G00067 2L
G00068 2M
Assembly Instructions
402B/402W OROBLANCO
Warning
1. Product is for single person use only.
2. Do not use this chair unless all bolts and knobs are securely tightened.
3. Check that all bolts and knobs are tightened every six months
or as needed.
4. Dispose of packing material properly. Do not use plastic cover as a head
covering. Suocation may result.
5. Do not use this chair as a stepladder.
* Arm Pad Lock Kit (L & M) & Arm Cap Kit (N, & O) are included.
For assistance, call [phone], or www.youtube.com/user/ideskInc1
A
B
C
D
E
F
G
ON
1
3 4
2
Ex1
Fx1
Gx5
3) J
A
2) J
Dx1
Align Back Frame mounting holes on both sides
Install items
in order of
red numbers
1) J 4) J
Cx1
Kx1 Kx1
Bx1
Nx1
For armless
chair

Back Frame G00021/G00038 1A
Item Part Name Part # Qty
Le Arm Cap G00069/G00071 1
1G00070/G00072Right Arm CapO
N
Pivot Lock Bracket
Slide Lock Bracket
Le Arm G00059/G00060 1B
Right Arm G00061/G00062 1C
Seat Pan G00063/G00064 1D
Gas Cylinder G00025 1E
Base G00026 1F
Caster G00008 5G
Hex Wrench G00028 1H
Short Bolt G00030 4J
Long Bolt G00065 2K
G00067 2L
G00068 2M
Assembly Instructions
402B/402W OROBLANCO
Warning
1. Product is for single person use only.
2. Do not use this chair unless all bolts and knobs are securely tightened.
3. Check that all bolts and knobs are tightened every six months
or as needed.
4. Dispose of packing material properly. Do not use plastic cover as a head
covering. Suocation may result.
5. Do not use this chair as a stepladder.
* Arm Pad Lock Kit (L & M) & Arm Cap Kit (N, & O) are included.
For assistance, call [phone], or www.youtube.com/user/ideskInc1
A
B
C
D
E
F
G
ON
1
3 4
2
Ex1
Fx1
Gx5
3) J
A
2) J
Dx1
Align Back Frame mounting holes on both sides
Install items
in order of
red numbers
1) J 4) J
Cx1
Kx1 Kx1
Bx1
Nx1
For armless
chair

Instructions Arm Pad Lock Kit
402B/402W OROBLANCO
5) Remove four screws that
secure the part for sliding
4) Remove the arm pad
2) Slide the arm pad back
and take a screwdriver
and pop o the cover
1) Bracket A & Bracket B
7) Make sure the angle
adjustment is straight,
then remove center screw
A
B
A
B
A
B
A
B
A
B
A
B
A
B
9) Place sliding part
back on
A
B
11) Reinstall the arm pad
using the same two
screws and secure
the pad.
A
B
12) Pop cover back on
A
B
3) Slide the arm pad
forward and remove
screws
6) Remove part
A
B
8) Place Bracket A
and use the same
screw to secure it
A
B
10) Pick any of the screw
holes to install Bracket B
and use the same screw
to secure it

Assembly Instructions Slip Cover
402B/402W OROBLANCO
3) Unzip old slip cover and remove
from foam
2) Remove old slip cover and foam
from seat pan by unfastening
the velcro fasteners on the back
and front of seat. Remove the
back fasteners first
4) Install new slip cover onto
the foam
6) Align 2 front corners and
install using velcro fasteners.
Li back of seat and zip up
slip cover. Align 2 back
corners and install using
velcro fasteners
5) Make sure all four slip cover
corners match to the foam
corners, top & bottom.
Close zipper approximately 2”
1) Assemble chair
2”

IMPORTANT ADDITIONAL
INSTALLATION INFORMATION (idesk Seating)
2/9
Installation tip for installing adjustable arm. Bolted Cap (Item L) must be aligned with the Long Bolt (Item M).
(Armrests for future shipment will be fully assembled.)
Model 402
Cx1
Lx1
Mx1 Mx1
Bx1
Lx1
Bolted Cap L
Long Bolt M