iDirect iQ 200 Installation instructions

Installation, Support, and
Maintenance Guide
iQ 200 Rackmount Satellite Router
Router Products
Evolution and Velocity
September 25, 2018
iQ 200 Rackmount Satellite Router Installation, Support, and
Maintenance Guide

ii Installation, Support, and Maintenance Guide
iQ 200 Rackmount Satellite Router
Copyright © 2018. VT iDirect, Inc., 13861 Sunrise Valley Drive, Suite 300, Herndon, VA 20171, USA.
All rights reserved. Reproduction in whole or in part without permission is prohibited. Information contained herein
is subject to change without notice. The specifications and information regarding the products in this document are
subject to change without notice. All statements, information and recommendations in this document are believed
to be accurate, but are presented without warranty of any kind, express, or implied. Users must take full
responsibility for their application of any products. Trademarks, brand names and products mentioned in this
document are the property of their respective owners. All such references are used strictly in an editorial fashion
with no intent to convey any affiliation with the name or the product's rightful owner.
VT iDirect®is a global leader in IP-based satellite communications providing technology and solutions that enable
our partners worldwide to optimize their networks, differentiate their services and profitably expand their
businesses. Our product portfolio, branded under the name iDirect®, sets standards in performance and efficiency
to deliver voice, video and data connectivity anywhere in the world. VT iDirect®is the world’s largest TDMA
enterprise VSAT manufacturer and is the leader in key industries including mobility, military/government and
cellular backhaul.
Company Web site: www.idirect.net ~ Main Phone: [phone]
TAC Contact Information: Phone: [phone] ~ Email: [email protected] ~ Web site: tac.idirect.net
iDirect Government™, created in 2007, is a wholly owned subsidiary of iDirect and was formed to better serve the
U.S. government and defense communities.
Company Web site: www.idirectgov.com ~ Main Phone: [phone]
TAC Contact Information: Phone: [phone] ~ Email: [e-mail] ~ Web site: tac.idirectgov.com
Document Name: ISM_iQ200Rackmount_T0001032_RevA_09252018.pdf
Document Part Number: T0001032

Installation, Support, and Maintenance Guide iii
iQ 200 Rackmount Satellite Router
Revision History
The following table shows all revisions for this document. To determine if this is the latest
revision, check the TAC Web site at http://tac.idirect.net.
Revision Date Updates
A September 25, 2018 Initial release of the document.

iv Installation, Support, and Maintenance Guide
iQ 200 Rackmount Satellite Router
Revision History

Installation, Support, and Maintenance Guide v
iQ 200 Rackmount Satellite Router
Contents
About . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Manual Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
Document Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
Related Training Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
Warranty, RoHS, WEEE, Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . xiv
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.2 Power Supply Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
2 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2.1 Mechanical and Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . .3
2.2 Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2.3 RF Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
3 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
3.1 iQ 200 Rackmount Satellite Router Front LEDs . . . . . . . . . . . . . . . . . . . . . . . .7
3.2 iQ 200 Rackmount Front Panel LED Status Descriptions . . . . . . . . . . . . . . . . . .8
3.3 iQ 200 Rackmount Satellite Router Rear Panel Descriptions . . . . . . . . . . . . . . 10
4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.1 Installation Steps at a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

vi Installation, Support, and Maintenance Guide
iQ 200 Rackmount Satellite Router
Contents
4.1.1 Pre-Installation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.1.2 Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.2 Tools and Supplies Required for Installation . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.3 Unpacking iDirect Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4.4 Components Typically Included in an Order . . . . . . . . . . . . . . . . . . . . . . . . .16
4.5 Mounting the iQ 200 Rackmount Satellite Router. . . . . . . . . . . . . . . . . . . . . . 16
4.5.1 Installing With an AC Power Supply (Option 1) . . . . . . . . . . . . . . . . . . . . . . . 17
4.5.2 Installing With a 36-76 VDC Power Supply (Option 2) . . . . . . . . . . . . . . . . . . . 17
4.6 Preparing the PC for Connection to the iQ 200 Rackmount Satellite Router . . . 18
4.7 Configuring the iQ 200 Rackmount Satellite Router . . . . . . . . . . . . . . . . . . . . 18
5 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.1 Safety Guidelines to Observe During Servicing . . . . . . . . . . . . . . . . . . . . . . . 19
5.1.1 Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.1.2 Conditions Requiring Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2 Maintaining the iQ 200 Rackmount Satellite Router . . . . . . . . . . . . . . . . . . . . 20
5.2.1 Temperature Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.2.2 90 day maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.3 Troubleshooting the iQ 200 Rackmount Router . . . . . . . . . . . . . . . . . . . . . . . 21
5.4 Removing and Replacing the Power Module . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.5 Repacking the iQ 200 Rackmount Satellite Router . . . . . . . . . . . . . . . . . . . . . 22
Appendix A Acronyms and Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . 23
Appendix B Tools Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Appendix C Cable Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
C.1 Coax Cable Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
C.2 Ethernet Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
C.2.1 Ethernet Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
C.2.2 Straight Through and Crossover RJ-45 Cables . . . . . . . . . . . . . . . . . . . . . . . 35
C.3 Console Port Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Installation, Support, and Maintenance Guide vii
iQ 200 Rackmount Satellite Router
Contents
Appendix D DC Power Supply Installation . . . . . . . . . . . . . . . . . . . . . . . . 37
Appendix E iQ 200 Rackmount Satellite Router Reset. . . . . . . . . . . . . . 41
E.1 Level 0 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
E.2 Level 1 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Installation, Support, and Maintenance Guide viii
iQ 200 Rackmount Satellite Router
Figures
Figure 1-1. iQ 200 Rackmount Satellite Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 3-1. iQ 200 Rackmount Satellite Router Front Panel LED Display . . . . . . . . . . . . . . . . 7
Figure 3-2. iQ 200 Rackmount Satellite Router Rear Panel Description . . . . . . . . . . . . . . . . 10
Figure B-1. Recommended Installation Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure C-1. Coax Cable Cutting Technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure C-2. Cutting Technique for Removing Foil in the Braid. . . . . . . . . . . . . . . . . . . . . . 31
Figure C-3. Procedure to Cut the Quad Shield Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure C-4. Attaching the Compression fitting F-type Connector . . . . . . . . . . . . . . . . . . . . 33
Figure C-5. Compression fitting F-Type Weatherproof Plug and Tool . . . . . . . . . . . . . . . . . 33
Figure C-6. RJ-45 Cable Connectors: Receptacle and Plug . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure C-7. Holding the RJ-45 Cable Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure C-8. RJ-45 to DB-9 Female DTE Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure D-1. DC-DC Power Supply Assembly at a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Installation, Support, and Maintenance Guide ix
iQ 200 Rackmount Satellite Router
Tables
Table 1-1. Power Supply Configurations................................................................... 2
Table 2-1. Mechanical and Environmental Specifications............................................... 3
Table 2-2. Power Specifications ............................................................................ 4
Table 2-3. RF Specifications ................................................................................. 5
Table 3-1. iQ 200 Rackmount Satellite Router Front Panel Description .............................. 8
Table 3-2. iQ 200 Rackmount Satellite Router Front Panel LED Descriptions........................ 8
Table 3-3. iQ 200 Rackmount Satellite Router Rear Panel Descriptions ............................. 10
Table 5-1. Troubleshooting Events and Actions to Take ............................................... 21
Table 5-2. Removing and/or Replacing the Power Module ............................................22
Table B-1. Recommended Installation Tools and Equipment.......................................... 27
Table C-1. Coax Trim Dimensions.......................................................................... 30
Table C-2. Ethernet Port Pinouts .......................................................................... 34
Table C-3. RJ-45 to DB-9 Pinouts .......................................................................... 35
Table D-1. iQ 200 Rackmount Router DC Power Module Connector Parts ........................... 37
Table D-2. Power Module Power Cable Installation Instructions Detail.............................. 38

x Installation, Support, and Maintenance Guide
iQ 200 Rackmount Satellite Router
Tables

Installation, Support, and Maintenance Guide xi
iQ 200 Rackmount Satellite Router
About
This manual provides important safety information and explains how to install and maintain
the iDirect iQ 200 Rackmount Satellite Router.
This chapter contains the following sections:
•Intended Audience
•Manual Contents
•Document Conventions
•Document Set
•Related Training Services
•Getting Help
•Warranty, RoHS, WEEE, Declaration of Conformity
Intended Audience
This manual is intended for use by the VSAT (Very Small Aperture Terminal) equipment
installer, System Engineer, and Network Operator responsible for maintaining the iDirect
Network. Only qualified service personnel should install the iQ 200 Rackmount Satellite
Router. Familiarity with cabling and wiring practices is beneficial.
Manual Contents
In addition to the information in this chapter, this manual also includes the following:
•Chapter 1, Introduction on page 1, provides an overview and description of the iQ 200
Rackmount Satellite Router.
•Chapter 2, Specifications on page 3describes the mechanical, environmental and RF
specifications of the iQ 200 Rackmount Satellite Router.
•Chapter 3, Interfaces on page 7provides connector descriptions of the iQ 200 Rackmount
Satellite Router.
•Chapter 4, Installation on page 13 describes procedures for installing the iQ 200
Rackmount Satellite Router.

xii Installation, Support, and Maintenance Guide
iQ 200 Rackmount Satellite Router
About
•Chapter 5, Maintenance on page 19 describes maintenance procedures for the iQ 200
Rackmount Satellite Router.
Document Conventions
This section illustrates and describes the conventions used throughout this document.
NOTE: A basic list of acronyms and abbreviations can be found in Appendix A,
Acronyms and Abbreviations.
Convention Description Example
Command Used when the user is required to
enter a command at a command
line prompt or in a console.
Enter the command:
cd /etc/snmp/
Terminal
Output
Used when showing resulting
output from a command that was
entered at a command line or on a
console.
crc report all
8350.3235 : DATA CRC [ 1]
8350.3502 : DATA CRC [5818]
8350.4382 : DATA CRC [ 20]
Screen
Reference
Used when referring to text that
appears on the screen on a
Graphical User Interface (GUI).
Used when specifying names of
commands, menus, folders, tabs,
dialogs, list boxes, and options.
1. To add a remote to an inroute group, right-click
the Inroute Group and select Add Remote.
The Remote dialog box has a number of user-
selectable tabs across the top. The Information
tab is visible when the dialog box opens.
Hyperlink Used to show all hyperlinked text
within a document or external
links such as web page URLs.
For instructions on adding a line card to the
network tree, see Adding a Line Card on
page 108.
WARNING: A Warning highlights an essential operating or maintenance
procedure, practice, condition, or statement which, if not strictly observed,
could result in injury, death, or long term health hazards.
CAUTION: A Caution highlights an essential operating or maintenance procedure,
practice, condition, or statement which, if not strictly observed, could result in
damage to, or destruction of, equipment or a condition that adversely affects
system operation.
NOTE: A Note is a statement or other notification that adds, emphasizes, or
clarifies essential information of special importance or interest.

Installation, Support, and Maintenance Guide xiii
iQ 200 Rackmount Satellite Router
About
Document Set
The following iDirect documents are available at TAC and contain information relevant to
installing and using iDirect satellite network software and equipment. Refer to Getting Help
on page xiii for TAC access information.
For Evolution®:
• iDX iBuilder User Guide
• iDX iMonitor User Guide
• Web iSite User Guide
• Terminal WUI User Guide
• Satellite Router Installation and Commissioning Guide
• Evolution Release Notes
• Evolution Technical Reference Guide
• Quick Start Guide (QSG), included in package with router
For iDirect Velocity®:
• Pulse NMS User Guide
• Regulatory Guide (Quick Start Guide)
• iDirect Velocity®Software Release Notes
• Terminal WUI User Guide
• Configuring iDirect Velocity Networks Using Pulse
Related Training Services
iDirect offers scheduled classroom training at various global training centers, as well as
eLearning, in the installation, operation, maintenance and management of iDirect satellite
networks. For training course descriptions and available training dates visit the iDirect web
site Training and Services at: http://www.idirect.net/Training-and-Services.aspx or call +1
[phone] for class registration and information.
Getting Help
The iDirect Technical Assistance Center (TAC) and the iDirect Government Technical
Assistance Center (TAC) are available to provide assistance 24 hours a day, 365 days a year.
Software user guides, installation procedures, FAQs, and other documents that support iDirect
and Direct Government products are available on the respective TAC Web site:
• Access the iDirect TAC Web site at http://tac.idirect.net
• Access the iDirect Government TAC Web site at http://tac.idirectgov.com
The iDirect TAC may be contacted by telephone or email:
• Telephone: [phone]
• E-mail: [email protected]
The Direct Government TAC may be contacted by telephone or email:

xiv Installation, Support, and Maintenance Guide
iQ 200 Rackmount Satellite Router
About
• Telephone: [phone]
• Email: [e-mail]
iDirect and iDirect Government produce documentation that are technically accurate, easy to
use, and helpful to our customers. Please assist us in improving this document by providing
feedback. Send comments to:
• iDirect: [email protected]
• iDirect Government: [e-mail]
For sales or product purchasing information contact iDirect Corporate Sales at the following
telephone number or e-mail address:
• Telephone: [phone]
• E-mail: [email protected]
Warranty, RoHS, WEEE, Declaration of Conformity
Complete iDirect hardware product statements for the iQ 200 Rackmount Satellite Router are
available at these Web sites:
•http://www.idirect.net/warranty, for the hardware warranty
•http://www.idirect.net/rohs, for the RoHS statement of compliance
•http://www.idirect.net/weee, for the WEEE statement of compliance
•http://www.idirect.net/doc, for the Declaration of Conformity

Installation, Support, and Maintenance Guide 1
iQ 200 Rackmount Satellite Router
1 Introduction
The iQ 200 Rackmount is iDirect’s next-generation DVB-S2/DVB-S2X remote with Adaptive
TDMA returns and is ideal for cost-effective, small to medium enterprise, and maritime
applications. The iQ 200 Rackmount combines high-performance iQ series features with
mobility and is compatible on both Evolution®and iDirect Velocity®.
This chapter contains the following sections:
• Section 1.1, Features on page 1
• Section 1.2, Power Supply Options on page 2
This manual explains how to safely install and maintain the iQ 200 Rackmount Satellite
Router. The iQ 200 Rackmount Satellite Router is shown in Figure 1-1.
Figure 1-1. iQ 200 Rackmount Satellite Router
1.1 Features
The iQ 200 Rackmount Satellite Router supports the following features:
• Single DVB-S2X (>100 Msps) demodulator
• Single A-TDMA (15 Msps) modulator
• Dual Image support
• OpenAMIP Mobility Support
• AES Encryption
• Two independent Gig-E LAN Ports
• Console port for NMEA GPS input
• Web GUI / Web Services support

2 Installation, Support, and Maintenance Guide
iQ 200 Rackmount Satellite Router
Power Supply Options
1.2 Power Supply Options
The iQ 200 Rackmount Satellite Router is available with these power supply configurations:
NOTE: The iQ 200 Rackmount can be ordered in any of the two configurations
specified in Table 1-1. The Power Supply Unit (PSU) is a Field Replaceable Unit
(FRU) and can be swapped in the field.
Table 1-1. Power Supply Configurations
Power Supply Option Description
100-240V AC +24V Power Supply (Standard) This AC power module for the iQ 200
Rackmount Satellite Router is standard
with a single +24V power support for the
BUC.
36-76V DC +24 V Power Supply This DC power module for the iQ 200
Rackmount Satellite Router comes with a
+24V power support for a +24V BUC.

Installation, Support, and Maintenance Guide 3
iQ 200 Rackmount Satellite Router
2 Specifications
This chapter describes the mechanical, environmental, power, RF specifications for the iQ 200
Rackmount Satellite Router and contains the following sections:
• Section 2.1, Mechanical and Environmental Specifications on page 3
• Section 2.2, Power Specifications on page 4
• Section 2.3, RF Specifications on page 5
2.1 Mechanical and Environmental Specifications
The installation site must be able to accommodate the iQ 200 Rackmount Satellite Router
mechanical and environmental specifications. The mechanical and environmental
specifications are listed in Table 2-1.
Table 2-1. Mechanical and Environmental Specifications
Category Description
Dimensions W 44.5 cm (17.5 in) x D 32 cm (12.6 in) x H 4.45 cm (1.75 in)
Weight 4.5 kg (10 lbs)
Heat Dissipation 16W average
Airflow Front Panel Fan Assist (2 fans), Power Supply (1 fan), Rear Exhaust,
No Filter
Ambient Temperature
Operational
Storage
+32˚F to +140˚F (0˚C to 60˚C)
De-rate 1.8˚F (1˚C) per 1,000 ft (304 m) above 5,000 ft (1,524 m)
Safety certified to 10,000 ft (3,048 m)
-40˚F to +185˚F (-40˚C to +85˚C)
Temperature Gradient 1.0 C per minute
Relative Humidity
Operational
Storage
10-90%, non-condensing
5 to 95%

4 Installation, Support, and Maintenance Guide
iQ 200 Rackmount Satellite Router
Power Specifications
2.2 Power Specifications
The iQ 200 Rackmount Satellite Router power specifications are listed in Table 2-2.
CAUTION: If negative voltages are used such as Telecom -48VDC, the negative
most voltage is always connected to –ve terminal (in the Telecom case this
would be -48V) and the positive most voltage is always connected to the +ve
terminal (in the Telecom case this would be 0VR). Chassis can be referenced
to +ve, -ve or left floating (i.e. not connected to either +ve or –ve) as
required as the power module is fully isolated input to the chassis.
Altitude
Operational
Storage
≤10,000 ft (3,048 m)
≤35,000 ft (10,668 m)
Shock
Operational
Survival
>= 10 G
≤40 G (ISTA-1A)
Vibration
Operational ETSI 300 019-2-6 Class 6.1, 5-200Hz
Table 2-1. Mechanical and Environmental Specifications (continued)
Category Description
Table 2-2. Power Specifications
Category Description
Input Voltage Range Option 1: 100-240 VAC, Auto-Ranging
Option 2: 36-76 VDC
Frequency Options 1: 50-60 Hz, Auto-Ranging
Remote Power Consumption 150 W (with 4 A BUC and 0.5 A LNB) MAX
AC PSU Current Rating Option 1: 2.7 A, 270 W (Power Supply capability)
DC PSU Current Rating Option 2: 8.3 A, 310 W (Power Supply capability)
DC Power @ TX Output
Connector
+24 V @ 4.0 A (Max)
DC Power @ RX Input
Connector
13, 18, 21 VDC @ 500mA (Max)
Protection Over-Voltage Protection for LNB and BUC DC
Over-Current Limiting for LNB and BUC DC
Options 1: Primary AC fuse within PS module (250 VAC, T6.3 A)
Option 2: Primary DC fuse within PS module (250 VDC, 16 A)
AC Power Cord Supplied, per country of use

Installation, Support, and Maintenance Guide 5
iQ 200 Rackmount Satellite Router
RF Specifications
2.3 RF Specifications
The iQ 200 Rackmount Satellite Router RF specifications are listed in Table 2-3.
DC Input Connector Self-capturing terminal block, 14-18 AWG
Efficiency of the Power
Supply
87% (MIN)
Table 2-2. Power Specifications (continued)
Category Description
Table 2-3. RF Specifications
Category Description
LNB Support 22 kHz tone for High / Low Band
IF Interface, Impedance Type “F”, Zo = 75 ohms
Frequency Range
Transmit
Receive
950 - 2150 MHz
950 - 2150 MHz
Tuning Step Size
Transmit
Receive
10 Hz
55 KHz
RF Power
Transmit
Receive, Maximum
Receive, Minimum
Pmax of +0 dBm to Pmin of -35 dBm
Max composite wide band receive level:
a) -5 dBm for symbol rates. 45 Msps
b) 10 dB above wanted signal power level for symbol rates > 45
Msps
Minimum Receive Level: -115+10*log (Fsym(sps)) single carrier
Receive adjust-ability- AGC Dynamic Range adjustment
Tx SSB Phase Noise
Receiver Noise Figure 15 dB
Transmit Carrier Suppression ≤-35 dBc
Discrete Spurs and Harmonic
Content
In-band (900-2150 MHz), with output at -30 dBm: . -35 dBc
Frequency Phase Noise
1 KHz -85 dBc/Hz
10 KHz -95 dBc/Hz
100 KHz -90 dBc/Hz
1 MHz -110 dBc/Hz

6 Installation, Support, and Maintenance Guide
iQ 200 Rackmount Satellite Router
RF Specifications
Transmitter Muting 50 dB (min) between carrier on and off states within 0.1 us at
the same attenuation state
Table 2-3. RF Specifications (continued)
Category Description