iFIT EXIF12.0 User manual

Congratulations for selecting the revolutionary iFit Module. Your
iFit Module will help you to create and manage a personal fitness
program designed to make your fitness goals a reality. With the iFit
Module, you can wirelessly download customized workouts, track
your workout results, get support, and even share your achieve-
ments on popular social networking sites. These are just some of the
features available with your iFit Module.
User’s Manual
Model No. EXIF12.0
QUESTIONS?
If you have questions after following the instructions in this manual,
PLEASE DO NOT CONTACT THE STORE. Please visit our
Customer Care website at support.iFit.com; send e-mail to
[email protected]; or call Customer Care toll-free at
1-866-608-1798, Mon.–Fri. 6 a.m.–6 p.m. MT, Sat. 8 a.m.–12 p.m.
MT (closed on holidays).
OPERATING REQUIREMENTS
To configure and use your iFit Module, you will need the following:
• A Wi-Fi®device, such as a computer, smartphone, or tablet
• A wireless 802.11b/g/n router with SSID broadcast enabled (hidden
networks are not supported)
• An Internet connection (a broadband connection is recommended;
performance depends on connection speed)
• An iFit.com membership
Note: The iFit Module supports unsecured and secured (WEP,
WPA™, and WPA2™) encryption.
COMPLIANCE INFORMATION
IMPORTANT: To comply with FCC and IC RF exposure compli-
ance requirements, the antenna used for this transmitter must
be installed to provide a separation distance of at least 8 in. (20
cm) from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION: To assure continued compliance, use only
shielded interface cables when connecting to computer or
peripheral devices. Any changes or modifications not expressly
approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
WARNING
Before beginning any exercise program, consult your
physician. This is especially important for persons over
age 35 or persons with pre-existing health problems.
ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this
product.

2
METHOD 1—WEBSITE
IMPORTANT: You will need to know your network SSID (network
name), network encryption type, and network password.
Note: You can use a variety of Internet browsers to configure the iFit
module. For best results, use the Google Chrome™ browser.
1. Create an iFit account.
On your computer,
smartphone, tablet,
or other Wi-Fi device,
open an Internet
browser and go to
www.iFit.com.
Follow the prompts on
the website to sign up
for your iFit member-
ship. If you have an
activation code, select
the code activation
option.
2. Log in to your iFit account.
Make sure that you are logged in to your iFit account. Go to
www.iFit.com, and follow the prompts on the website to log in to
your iFit account.
3. Go to the iFit Module Setup web page.
After you have logged in to your iFit account, go to
www.iFit.com/wifi. Your browser will load the iFit Module Setup
web page.
4. Insert the iFit Module into the console.
Insert the iFit Module
into the iFit port on your
fitness equipment con-
sole. An LED indicator
light on the iFit Module
will glow amber.
To learn how to read the
indicator light on the iFit
Module, see the back
cover of this manual.
IMPORTANT: If your
fitness equipment
console has a tablet holder, you may have to remove the tab-
let holder to access the iFit port. To remove the tablet holder,
see your fitness equipment user’s manual. After you insert
and configure the iFit module, reattach the tablet holder.
5. Select the network IFIT_SETUP.
On your computer, smartphone, tablet, or other Wi-Fi device,
open the list of available networks to which your device can con-
nect. One of the options will be IFIT_SETUP; select this network.
If this network does not appear, make sure that your Wi-Fi device
is within range of the console, and then close and re-open your
list of networks.
Note: It may take a few minutes for the network IFIT_SETUP
to appear. The network IFIT_SETUP will not appear if the iFit
Module has already been configured to connect to a wireless
network. Go to step 9 and reset the iFit Module.
6. Begin the setup process.
A prompt on the iFit Module Setup web page will notify you when
your Wi-Fi device is connected to the network IFIT_SETUP.
When the prompt appears, click the Setup WiFi Module button to
begin the setup process. Then, your browser will load a new web
page.
7. Choose the basic or the advanced setup option.
On the new web page, select either the basic setup option or the
advanced setup option. Then, enter the requested information
into the fields on the web page.
If you select the basic setup option, you will be requested to
select your network and to enter your network password (if your
network has a password).
If you select the advanced setup option, you will be requested
to select your network and to enter your network password,
your IP address, your netmask, your gateway address, and your
global DNS server.
After you enter the requested information, click the submit button
on the web page.
8. Wait for the setup process to finish.
If the setup process is successful, the indicator light on the iFit
Module will glow green.
The iFit Module is now connected to your wireless network and
you are logged in to your iFit account. Go to step 10.
If the setup process has failed, the indicator light will glow red.
Go to step 9 and reset the iFit Module.
9. Reset the iFit Module if necessary.
To reset the iFit Module’s s e t t i n g s a n d s t a r t t h e c o n f i g u r a t i o n
process over, press and hold the Reset button on the iFit Module
for a few seconds; do not remove the iFit Module from the iFit
port on the console.
The indicator light will glow amber when the iFit Module is ready
again for setup. Then, repeat steps 3 to 8.
10. The iFit Module is now configured.
To learn how to read the indicator light on the iFit Module, see
the back cover of this manual.
To use the iFit Module, see your fitness equipment user’s manual
or go to support.iFit.com.
If you have questions after following these instructions, go to
support.iFit.com for assistance.
If Method 1 for configuring the iFit Module does not work, see
the instructions for Method 2 on page 3.
iFit
Module
HOW TO CONFIGURE YOUR IFIT MODULE

3
METHOD 2—IP ADDRESS
IMPORTANT: You will need to know your network SSID (network
name), network encryption type, and network password.
Note: You can use a variety of Internet browsers to configure the iFit
module. For best results, use the Google Chrome™ browser.
1. Insert the iFit Module into the console.
Insert the iFit Module
into the iFit port on your
fitness equipment con-
sole. An LED indicator
light on the iFit Module
will glow amber.
To learn how to read the
indicator light on the iFit
Module, see the back
cover of this manual.
IMPORTANT: If your
fitness equipment
console has a tablet holder, you may have to remove the tab-
let holder to access the iFit port. To remove the tablet holder,
see your fitness equipment user’s manual. After you insert
and configure the iFit module, reattach the tablet holder.
2. Select the network IFIT_SETUP.
On your computer,
smartphone, tablet,
or other Wi-Fi device,
open the list of available
networks to which your
device can connect.
One of the options will
be IFIT_SETUP; select
this network.
If this network does not appear, make sure that your Wi-Fi device
is within range of the console, and then close and re-open your
list of networks.
Note: It may take a few minutes for the network IFIT_SETUP
to appear. The network IFIT_SETUP will not appear if the iFit
Module has already been configured to connect to a wireless
network. Go to step 6 and reset the iFit Module.
3. Go to the setup web page.
Open a web browser on your computer, smartphone, tablet, or
other Wi-Fi device. Next, type the following IP address into the
URL bar in your browser: http://192.168.0.1:8080
Your browser will load a web page. If the web page does not
appear, double-check the IP address and the previous instruc-
tions of this step.
4. Connect the iFit Module to your wireless network.
Follow the instructions on the web page to connect the iFit
Module to your wireless network.
5. Wait for the setup process to finish.
If the setup process is successful, the indicator light on the iFit
Module will glow green. The iFit Module is now connected to your
wireless network and you are logged in to your iFit account. Go
to step 7.
If the setup process has failed, the indicator light will glow red.
Go to step 6 and reset the iFit Module.
6. Reset the iFit Module if necessary.
To reset the iFit Module and start the configuration process over,
press and hold the Reset button on the iFit Module for a few
seconds; do not remove the iFit Module from the iFit port on
the console.
The indicator light will glow amber when the iFit Module is ready
again for setup. Then, repeat steps 1 to 5.
7. The iFit Module is now configured.
To learn how to read the indicator light on the iFit Module, see
the back cover of this manual.
To use the iFit Module, see your fitness equipment user’s manual
or go to support.iFit.com.
If you have questions after following these instructions, go to
support.iFit.com for assistance.
iFit
Module

ICON Health & Fitness, Inc. (ICON) warrants this product to be
free from defects in workmanship and material, under normal
use and service conditions. Parts and labor are warranted for
ninety (90) days from the date of purchase.
This warranty extends only to the original purchaser (customer).
ICON’s obligation under this warranty is limited to repairing or
replacing, at ICON’s option, the product through one of its autho-
rized service centers. All repairs for which warranty claims are
made must be preauthorized by ICON. If the product is shipped
to a service center, freight charges to and from the service cen-
ter will be the customer’s responsibility. For replacement parts
shipped while the product is under warranty, the customer will be
responsible for a minimal handling charge. This warranty does
not extend to any damage to a product caused by or attribut-
able to freight damage, abuse, misuse, improper or abnormal
usage, or repairs not provided by an ICON authorized service
center; to products used for commercial or rental purposes or as
store display models; or to products transported or purchased
outside the US. No other warranty beyond that specifically set
forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or conse-
quential damages arising out of or in connection with the use or
performance of the product; damages with respect to any eco-
nomic loss, loss of property, loss of revenues or profits, loss of
enjoyment or use, or costs of removal or installation; or other
consequential damages of whatsoever nature. Some states do
not allow the exclusion or limitation of incidental or consequen-
tial damages. Accordingly, the above limitation may not apply
to you.
The warranty extended hereunder is in lieu of any and all other
warranties, and any implied warranties of merchantability or
fi t n e s s f o r a p a r t i c u l a r p u r p o s e a r e l i m i t e d i n t h e i r s c o p e a n d
duration to the terms set forth herein. Some states do not allow
limitations on how long an implied warranty lasts. Accordingly,
the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have
other rights that vary from state to state.
ICON Health & Fitness, Inc.
1500 S. 1000 W., Logan, UT 84321-9813
Part No. 339339 R1014A Printed in China © 2014 ICON Health & Fitness, Inc.
IFIT is a registered trademark of ICON Health & Fitness, Inc. | Google Chrome is a trademark of Google Inc.
Wi-Fi is a registered trademark of Wi-Fi Alliance. WPA and WPA2 are trademarks of Wi-Fi Alliance.
LIMITED WARRANTY
HOW TO READ THE LED INDICATOR LIGHT
Indicator Color Flashes Meaning Troubleshooting Action
Amber No Broadcasting “IFIT_SETUP” None
Amber Constantly Connecting to wireless network None
Green No Connected to wireless network and logged in
to iFit.com None
Green Constantly Sending data None
Red to Green Alternately Performing an update None
Red No Network connection failed Reset the iFit Module and repeat the
configuration process
Red Constantly There is an internal error in the iFit Module Remove the iFit Module, wait one minute,
and then re-insert the iFit Module
Red Once There is an issue with your wireless router Reset the iFit Module and repeat the
configuration process
Red Twice There is an issue with your Internet
connection
Reset the iFit Module and repeat the
configuration process
Red Three times There is an issue with the DNS server Reset the iFit Module and repeat the
configuration process
Red Four times There is an issue connecting to iFit.com Repeat the configuration process at a later
time
Red Five times Your iFit username and password were not
entered correctly
Enter your iFit username and password
correctly