iHealth Clear User manual

English
Français
Deutsch
Italiano
Press to change
language
Press to confirm
language
Press to change
language
Press to confirm
language
English
Français
Deutsch
Italiano
2
1
2
3
4
Place cuff over left arm so the cuff tubing is centered on the
inside of your arm and aligned with your middle finger.
Fully charge the blood pressure
monitor before first use.
6
13
Rest your bare (or thinly clothed) left arm flat on a table. The bottom of the cuff should be about 1/2" above your
elbow. Tighten the cuff firmly, leaving about 1 finger space. 5
Wireless Network Setup
Quick Start Guide
Measurement
Make sure to fully insert the
cuff tubing connector into
the blood pressure monitor.
Note the direction of the
cuff tubing and alignment
with your middle finger.
Clear
Press any button to stop a measurement and to turn off the
monitor.
1/2 inch (1-2 cm)
Press and hold the User 2 button for 10 seconds until the
screen displays the select language page.
The screen will display the wireless network setup page.
Launch the iHealth MyVitals app, go to Select New Devices
and choose Clear (BPM1). Follow the on-screen instructions
to finish setting up your wireless network.
Ready to connect, launch MyVitals
app.
Connecting WiFi...
Setup complete! Your blood pressure
measurements will automatically
upload to the iHealth MyVitals app.
Insert cuff tubing connector into blood pressure monitor
unit, and the monitor will power on automatically.
Press User 1 or User 2 button again to start a measurement.
During the measurement, you will feel the cuff tightening
around your arm. Remain still and do not move your arm
until the measurement is complete.
Go to the Apple App Store or Google Play Store and search
"iHealth MyVitals." Download the app and then log in.
You will need to select your language after turning on the
monitor for the first time.
EN
All manuals and user guides at all-guides.com

English
Français
Deutsch
Italiano
Press to change
language
Press to confirm
language
Press to change
language
Press to confirm
language
English
Français
Deutsch
Italiano
2
1
2
3
4
Place cuff over left arm so the cuff tubing is centered on the
inside of your arm and aligned with your middle finger.
Fully charge the blood pressure
monitor before first use.
6
13
Rest your bare (or thinly clothed) left arm flat on a table. The bottom of the cuff should be about 1/2" above your
elbow. Tighten the cuff firmly, leaving about 1 finger space. 5
Wireless Network Setup
Quick Start Guide
Measurement
Make sure to fully insert the
cuff tubing connector into
the blood pressure monitor.
Note the direction of the
cuff tubing and alignment
with your middle finger.
Clear
Press any button to stop a measurement and to turn off the
monitor.
1/2 inch (1-2 cm)
Press and hold the User 2 button for 10 seconds until the
screen displays the select language page.
The screen will display the wireless network setup page.
Launch the iHealth MyVitals app, go to Select New Devices
and choose Clear (BPM1). Follow the on-screen instructions
to finish setting up your wireless network.
Ready to connect, launch MyVitals
app.
Connecting WiFi...
Setup complete! Your blood pressure
measurements will automatically
upload to the iHealth MyVitals app.
Insert cuff tubing connector into blood pressure monitor
unit, and the monitor will power on automatically.
Press User 1 or User 2 button again to start a measurement.
During the measurement, you will feel the cuff tightening
around your arm. Remain still and do not move your arm
until the measurement is complete.
Go to the Apple App Store or Google Play Store and search
"iHealth MyVitals." Download the app and then log in.
You will need to select your language after turning on the
monitor for the first time.
EN
All manuals and user guides at all-guides.com

English
Français
Deutsch
Italiano
Press to change
language
Press to confirm
language
Press to change
language
Press to confirm
language
English
Français
Deutsch
Italiano
2
1
2
3
4
Place cuff over left arm so the cuff tubing is centered on the
inside of your arm and aligned with your middle finger.
Fully charge the blood pressure
monitor before first use.
6
13
Rest your bare (or thinly clothed) left arm flat on a table. The bottom of the cuff should be about 1/2" above your
elbow. Tighten the cuff firmly, leaving about 1 finger space. 5
Wireless Network Setup
Quick Start Guide
Measurement
Make sure to fully insert the
cuff tubing connector into
the blood pressure monitor.
Note the direction of the
cuff tubing and alignment
with your middle finger.
Clear
Press any button to stop a measurement and to turn off the
monitor.
1/2 inch (1-2 cm)
Press and hold the User 2 button for 10 seconds until the
screen displays the select language page.
The screen will display the wireless network setup page.
Launch the iHealth MyVitals app, go to Select New Devices
and choose Clear (BPM1). Follow the on-screen instructions
to finish setting up your wireless network.
Ready to connect, launch MyVitals
app.
Connecting WiFi...
Setup complete! Your blood pressure
measurements will automatically
upload to the iHealth MyVitals app.
Insert cuff tubing connector into blood pressure monitor
unit, and the monitor will power on automatically.
Press User 1 or User 2 button again to start a measurement.
During the measurement, you will feel the cuff tightening
around your arm. Remain still and do not move your arm
until the measurement is complete.
Go to the Apple App Store or Google Play Store and search
"iHealth MyVitals." Download the app and then log in.
You will need to select your language after turning on the
monitor for the first time.
EN
All manuals and user guides at all-guides.com

English
Français
Deutsch
Italiano
Press to change
language
Press to confirm
language
Press to change
language
Press to confirm
language
English
Français
Deutsch
Italiano
2
1
2
3
4
Place cuff over left arm so the cuff tubing is centered on the
inside of your arm and aligned with your middle finger.
Fully charge the blood pressure
monitor before first use.
6
13
Rest your bare (or thinly clothed) left arm flat on a table. The bottom of the cuff should be about 1/2" above your
elbow. Tighten the cuff firmly, leaving about 1 finger space. 5
Wireless Network Setup
Quick Start Guide
Measurement
Make sure to fully insert the
cuff tubing connector into
the blood pressure monitor.
Note the direction of the
cuff tubing and alignment
with your middle finger.
Clear
Press any button to stop a measurement and to turn off the
monitor.
1/2 inch (1-2 cm)
Press and hold the User 2 button for 10 seconds until the
screen displays the select language page.
The screen will display the wireless network setup page.
Launch the iHealth MyVitals app, go to Select New Devices
and choose Clear (BPM1). Follow the on-screen instructions
to finish setting up your wireless network.
Ready to connect, launch MyVitals
app.
Connecting WiFi...
Setup complete! Your blood pressure
measurements will automatically
upload to the iHealth MyVitals app.
Insert cuff tubing connector into blood pressure monitor
unit, and the monitor will power on automatically.
Press User 1 or User 2 button again to start a measurement.
During the measurement, you will feel the cuff tightening
around your arm. Remain still and do not move your arm
until the measurement is complete.
Go to the Apple App Store or Google Play Store and search
"iHealth MyVitals." Download the app and then log in.
You will need to select your language after turning on the
monitor for the first time.
EN
All manuals and user guides at all-guides.com

English
Français
Deutsch
Italiano
Press to change
language
Press to confirm
language
Press to change
language
Press to confirm
language
English
Français
Deutsch
Italiano
2
1
2
3
4
Place cuff over left arm so the cuff tubing is centered on the
inside of your arm and aligned with your middle finger.
Fully charge the blood pressure
monitor before first use.
6
13
Rest your bare (or thinly clothed) left arm flat on a table. The bottom of the cuff should be about 1/2" above your
elbow. Tighten the cuff firmly, leaving about 1 finger space. 5
Wireless Network Setup
Quick Start Guide
Measurement
Make sure to fully insert the
cuff tubing connector into
the blood pressure monitor.
Note the direction of the
cuff tubing and alignment
with your middle finger.
Clear
Press any button to stop a measurement and to turn off the
monitor.
1/2 inch (1-2 cm)
Press and hold the User 2 button for 10 seconds until the
screen displays the select language page.
The screen will display the wireless network setup page.
Launch the iHealth MyVitals app, go to Select New Devices
and choose Clear (BPM1). Follow the on-screen instructions
to finish setting up your wireless network.
Ready to connect, launch MyVitals
app.
Connecting WiFi...
Setup complete! Your blood pressure
measurements will automatically
upload to the iHealth MyVitals app.
Insert cuff tubing connector into blood pressure monitor
unit, and the monitor will power on automatically.
Press User 1 or User 2 button again to start a measurement.
During the measurement, you will feel the cuff tightening
around your arm. Remain still and do not move your arm
until the measurement is complete.
Go to the Apple App Store or Google Play Store and search
"iHealth MyVitals." Download the app and then log in.
You will need to select your language after turning on the
monitor for the first time.
EN
All manuals and user guides at all-guides.com

English
Français
Deutsch
Italiano
Press to change
language
Press to confirm
language
Press to change
language
Press to confirm
language
English
Français
Deutsch
Italiano
2
1
2
3
4
Place cuff over left arm so the cuff tubing is centered on the
inside of your arm and aligned with your middle finger.
Fully charge the blood pressure
monitor before first use.
6
13
Rest your bare (or thinly clothed) left arm flat on a table. The bottom of the cuff should be about 1/2" above your
elbow. Tighten the cuff firmly, leaving about 1 finger space. 5
Wireless Network Setup
Quick Start Guide
Measurement
Make sure to fully insert the
cuff tubing connector into
the blood pressure monitor.
Note the direction of the
cuff tubing and alignment
with your middle finger.
Clear
Press any button to stop a measurement and to turn off the
monitor.
1/2 inch (1-2 cm)
Press and hold the User 2 button for 10 seconds until the
screen displays the select language page.
The screen will display the wireless network setup page.
Launch the iHealth MyVitals app, go to Select New Devices
and choose Clear (BPM1). Follow the on-screen instructions
to finish setting up your wireless network.
Ready to connect, launch MyVitals
app.
Connecting WiFi...
Setup complete! Your blood pressure
measurements will automatically
upload to the iHealth MyVitals app.
Insert cuff tubing connector into blood pressure monitor
unit, and the monitor will power on automatically.
Press User 1 or User 2 button again to start a measurement.
During the measurement, you will feel the cuff tightening
around your arm. Remain still and do not move your arm
until the measurement is complete.
Go to the Apple App Store or Google Play Store and search
"iHealth MyVitals." Download the app and then log in.
You will need to select your language after turning on the
monitor for the first time.
EN
All manuals and user guides at all-guides.com