iHome iW4 Guide

1. The iW4 will automatically sync the clock time when docking an iPad, iPhone, or iPod.
2. Press & hold the Clock Sync button and use the + | - buttons to manually set the time and calendar.
3. Press Alarm 1 or Alarm 2 button during time set for 12|24 hour mode.
4. Press the Snooze | Dimmer button to adjust the brightness of the clock display backlight.
Set alarm & wake preferences:
1. Press Alarm 1 or 2 buttons to preview programmed alarm time and press again to turn the alarm ON or OFF.
2. Press & hold Alarm 1 or 2 buttons to set alarm and wake preferences (alarm time,repeat, source and wake volume)
3. Press Wakeup| Alarm Sk ip or Power buttons to stop and reset a sounding alarm
4. Press Wakeup| Alarm Sk ip buttonto sk ip the next pending programmed alarm time
5. Press & hold Wakeup | Alarm Skip buttonto adjust the‘Gentle Wake’timer (O, 1-10 minutes)
Note: Pressing the + | - buttons will adjust device settings within alarm and time settings.
Multi-room audio
Add AirPlay-enabled speakers to any room
iHome’sAirPlay solutions provide an aordable way to enjoy a truly wireless home audio experience anywhere you
want - including kitchen, bedroom, livingroom or patio.
Apps
Othernetwork
Wi-Fi Networks
10:09PM
YourWi-Fi Network
Choose a Network for iW4
Other Wi-Fi Network
Settings
Other Wi-Fi Network
Other Wi-Fi Network
Other Wi-Fi Network
Wi-Fi
ShowDetails
iHome iW4 XXXXXX
Model: iHome iW4 • Firmware: 8.0.0
Name
Searchfor Update
FirmwareUpdate
SpeakerName
Network Refresh
NetworksiW4
Quick Wi-Fi Setup Instructions
Step1: Press the “Network Setup”
button on the rear panel of your
AirPlay speaker.
Step 2: When prompted, press
“Allow” to share your Wi-Fi settings
Note: it can take up to 3 minutes for your
AirPlay speaker to connect to the Wi-Fi
netwrok you just shared.The “Network
Status” LED on the rear panel of your
speaker will turn solid green when it has
successfully established a connection.
iW4About ManualSetup
O
thernetwork
Other
Wi
-
Fi
Network
Oth
Other
Other
Oe
Wi Fi
Wi-Fi
Wi-Fi
Nt
Networ
Networ
eo
k
k
k
M
o
del: iH
o
meiW4 • Firmware:
8
.0.0
Sh
Search
Search
fUd
forUpd
forUpd
t
ate
ate
Fi
Firmwar
Firmwar
Firmwar
Udt
eUpdat
eUpdat
eUpdat
p
e
e
e
iHome
iW4
XXX
XXX
Name
py
AirPla
y
speaker to connect to t
h
e Wi-F
i
netwro
netwro
netwro
kyou
kyou
k you
you
just s
just s
just s
just s
hared
hared.
hared.
The “
The
The
Networ
Networ
Networ
k
k
k
Status
Status
Status
Status
Status
Status
” LED
” LED
LED
LED
LED
on the
on the
on the
on the
on the
on the
rear
rear
rear
rear
rear
panel
panel
panel
panel
panel
panel
p
of you
of you
of you
of you
of you
of you
y
r
r
r
r
k
k
speake
speake
speake
speake
p
ill
ill
r will
r will
r will
r will
t
turn
turn
turn
turn
lid
lid
solid
solid
solid
solid
green
green
green
green
g
hi
hi
when i
when i
when i
when i
h
th
thas
thas
thas
t has
succes
fll
sfully
tb
estab
li h d
lished
a con
ti
nectio
n.
10:09PM 10:09PM
1. Verify that the iW4 is powered on.
2. Dock your iPad, iPhone or iPod touch with the iW4.
3. Download our free iHome Set app from the App Store and launch.
4. Scroll down the app interface and select the ‘Network’tab interface and then select ‘Manual Setup’button.
5. Select your preferred Wi-Finetwork from the list of available networks and enter password if prompted. Select
‘Other Network’ to connect to network with a hidden SSID.
Note: Connecting to a network may take up to 2 minutes. If network connection is unsuccessful reset the unit or
disconnect your iOS device and reconnect and repeat the above steps.
6. To rename youriW4 speaker, exit manual network setup, select ‘Speaker Name’ and customize how your iW4
speaker will present itself on your network. Press ‘DONE’ to conrm the new name.
power
sync
alarmskip
alarm2alarm1presetseq nap
aux-in
networksetupstatus
12V3.5A
networksetup
status
Connect
10:09PM
ShareWi-FiSettings?
Allow Ignore
Doyouwant to share your Wi-Fi
settingssothis accessory can
connecttothe Wi-Fi network?
Connect
power
sync
alarmskip
alarm2alarm1presetseq nap
10:09PM
Livingroom Speaker
Change Device Name
iW4
QWE R T Y U I OP
ASDFGHJK L
ZXCVBNM
space Done?123
Thisname will be displayed when selecting your
speakerfrom a list of available AirPlay devices.
Wi-Fi
ShowDetails
NotConnected
iHomeiW4 XXXXXX
Model: iHome iW4 • Firmware: 8.0.0
Name
Searchfor Update
FirmwareUpdate
SpeakerName
Network Refresh
10:09PM
About
A
S
D
F
G
H
J
K
L
Z
Z
Z
Z
Z
Z
Z
X
X
X
X
X
X
X
C
C
C
C
C
C
C
V
V
V
V
V
V
V
B
B
B
B
B
B
B
N
N
N
N
N
N
N
M
M
M
M
M
M
M
sp
ace D
o
ne
?
12
3
Mdl
Model:
Model:
Model:
Model:
iH iW
iHomeiW
iHomeiW
iHomeiW
iHomeiW
4Fi
4•Fir
4•Fir
4•Fir
4 Fir
8
mware:8
mware:8
mware:8
mware:8
00
00
00
.0.0
.0.0
Searchfor U
p
date
Audio modes, clock settings, and alarms
1. Verify that the iW4 is powered on.
2. Activate Wi-Fi on youriPad, iPhone, or iPod touch (with iOS 5.0 or later) and connect to your preferred network.
3. Dock your iPad, iPhone or iPod touch with the iW4.
4. Press the Network Setup button on the back of the iW4
5. A pop-up message will appear on the iOS device asking if you want to share your Wi-Fisettings. Select ‘Allow’.
Connect
ShareWi-FiSettings?
Allow Ignore
Doyouwanttoshare yourWi-Fi
settingssothisaccessorycan
connecttotheWi-Finetwork?
power
sync
alarmskip
alarm2alarm1presetseq nap
aux-in
networksetupstatus
12V3.5A
networksetup
status
power
sync
alarmskip
alarm2alarm1presetseq nap
- TurniW4 ON and select AirPlay mode
- Launch iTunes or use youriPad, iPhone,
iPad touch (verify network settings)
- Select the‘iHome iW4 XXXXXX’speaker as
your audio source (look for AirPlay logo)
Enjoy AirPlay wireless audio
- Press the Power button to switch
bet weenpower ON and standby
- Press & hold the Power button (4 sec.)
to turn iW4’s Wi-Fi network OFF/ON
I’ve selected the iW4 speaker
as my AirPlay audio source,
but I do not hear any music.
Visit our website for additional network setup instructions: www.ihomeaudio.com/support/airplay/
Network Setup for AirPlay
Display Indicators
Visit our website for the complete iW4 user manual and help: www.ihomeaudio.com/support/airplay/
Problem Possible Solutions
I’ve successfully connected
the iW4 to my home
network, but I cannot select
the iW4 speaker from iTunes/
iOS Device OR control AirPlay
music playback using
buttons
The iW4 speaker must be on the same network as your AirPlay source.
iTunes Solutions:
1. Make sure that you have the latest version if iTunes.
2. ry restarting iTunes.
3. Before you open iTunes,make sure that you have enabled Bonjour
service in your PC. TakeWindows XP for example: to enable the service,
you can click Start->Settings-> Control Panel, and double click
Administrative Tools-> Services->Bonjour Service, then click Star t
followed by OK on the pop-up menu.
4. In order for the iW4 to be able to access track controls in iTunesyou
need to allow it in iTunes:
- In iTunes, go to Preferences.
- In the Devices tab, check "Allow iTunes audio control from
remote speaker"
iOS device solutions:
1. Make sure the iOS device has the latest software.
2. If you are unable to see the Airplay icon on the iOS device, restart your
iOS device.
3. Verify that your device is connected to the correctWi-Fi network.
Note: The original iPhone, iPhone 3G, and iPod touch (1st gener-
ation) do not support AirPlay.
1. Verify that the adaptor is connected, that the power outlet is ‘live’
(not controlled by a wall switch), and battery is fully charged.
2. Reset the iW4 speaker (Disconnect the AC power and backup
battery and reconnect after 15 seconds).
1. Verify that the volume is not muted or set to 0.
2. Verify that there is not another iTuneslibrar y or iOS device connected
to the iW4 speaker.
3. Try restarting iTunes or your iOS device.
4. Reset the iW4 and reboot your Wi-Firouter.
The iW4 doesn’t respond or
doesn’t turn ON.
1. Reset the iW4 speaker (Disconnect the AC power and backup
battery and reconnect after 15 seconds) and reboot your
iPad/iPhone/iPod.
Docking error message: “This
device is not supported”
Network Setup Check list:
Option A - Connection via Wi-Fi Sharing with iOS 5.0 (RECOMMENDED)
To enjoy AirPlaywireless audio, you must have the following:
- iTunes or an iOS device (iPod touch, iPhone, or iPad).
- A functioning home network with Wi-Fi or direct ethernet connection.
Download the latest software updates for iTunes and your iOS deviceto ensure that you are able to enjoy the latest
AirPlay enhancements and compatibility.
Download the iHome Set app for iPod touch, iPhone and iPad.
Have your Wi-Finetwork name (SSID) and password (if applicable) available for reference.
If you use security for your network, use WPA/WPA2 security (not WEP orWPA/WPA2 enterprise)
Note: AirPlay requires iTunes 10.1 (Mac and PC) or later; OR an iPad (1st, 2nd, and 3rd generations) iPhone (4S, 4, and
3GS), iPod touch (4th, 3rd, and 2nd generations) with iOS 4.2 or later. The iHome Set app requires iOS 4.2 or later.
Overview
iW4 Start Guide
Visit our website for additional help and how-to videos
www.ihomeaudio.com/support/airplay/
Control Troubleshooting
iW4- Start Guide (US)
size: 740W x 148H (mm)
April 23, 2012 (Matte PP coating)
iW4- Start Guide (US)
size: 740W x 148H (mm)
April 23, 2012 (Matte PP coating)
AirPlay & iPod touch, iPhone, or iPad
Using an iOS device:
1. Connect your iOS device to the same Wi-Finetwork as iW4. Go to Settings --> Wi-Fi on your iOS device.
2. Tap on iPod Music app,look for the AirPlay icon next to the iPod music transport controls.
3. Tap on the AirPlay icon and choose iW4 fromthe list of speakers. If the iW4 speaker is not available, restart
your iOS device and verify that the iW4 is powered on.
4. Press play.
AirPlay & iTunes
Using a Mac or PC with iTunes (AirPlay streaming is designed foriTunes media and audio content only):
1. Connect your Mac or PC to the same Wi-Finet workas iW4.
2. Open iTunes on your computer.
3. Within iTunes open“Preferences”, Select the “Devices”tab, and activate the following option:
“Allow iTunes control from remote speakers”
4. Click OK, close iTunes preferences.
5. Look for the AirPlay icon in the bottom right corner of the iTuneswindow.
6. Click the AirPlay icon and choose iW4 from the list of speakers. Click "Multiple Speakers..." toselec t additional
AirPlay speakers. If the iW4 speaker is not available, restart iTunes and verify that the iW4 is powered on.
7. Press play.
AirPlay
ppp
not available, restart iTunes and veri
f
y
that the iW4 is
po
wered on.
iHomeiW4 speaker
iW4 v2NJ 04.23.2012
Problem Possible Solutions
I am unable to connect the
iW4 to my home Wi-Fi
network.
1. Verify that your Wi-Fi network is functioning and Wi-Fi certied.
2. The iW4 does not support WEP or WPA/WPA2 Enterprise security
types. We recommend Open, WPA/WPA2 Personal. Once you change
the security type on your router, we suggest rebooting yourWi-Fi
router and your iW4 speaker.
3. Make sure your router rmware is up to date.
4. Make sure that your wireless network is not on a conicting channel
with one of your neighbors. You can use software like iStumbler on
Mac or Netstumbler on Windows to verify that adjacent networks,
sorted by SNR, aren't on the same channel. Channels 1, 6, and 11 are
the three non-overlapping 802.11g channels.
5. Move the iW4 closer to your network access point; the Wi-Fi signal is
weak or there are overlappingWi-Fi signals or the iW4 is out of range
of your Wi-Finet work.
6. Keep away from potential sources of interference which may aect
Wi-Fi signal, such as microwaveovens.
7. Reset the iW4 Hardware and repeat network setup:
Option 1:
- Press & hold the Power button (4 sec.) to turn network OFF.
- Press & hold the Power button again to reactivate the network.
Option 2:
- Disconnect the AC power and backup battery and reconnect
after 15 seconds.
© 2012 SDI TechnologiesInc. All rights reserved.
iHome and the logo are registeredtrademarks of SDI Technologies.
AirPlay, iPad,iPhone, iPod touch, iPod, are registered trademarks of Apple Inc.
TuneIn® is a registeredtrademark of TuneIn, Inc.
PANDORA®is a registered trademark of Pandora Media Inc.
iHeartRadio® is a registered trademark of Clear Channel Communications, Inc.
Printed in China.
iW4 04232012-A
Your iOS device will sharecurrent wireless network credentials with the iW4 and a conrmation tone will sound.
Verify that the Network Status LED is green and then keep reading to learn how to use iW4 tostream your iTunes
and iOS audio content using AirPlay.
If you have an iPod touch, iPhone, or iPad with iOS 5.0 or later, we recommend that you use
Wi-Fi network log-in sharing for the quickest network setup experience.
Congratulations, you have successfully connected your iW4 to your wireless network. Verify that
the Network Status LED is green and that the Network Status Indicator icon shows signal
strength to conrm if the iW4 is successfully connected to a network. Keep reading on the other
side of this guide to start using AirPlay and other iW4 features.
Controls BatteryLow Indicator
FirmwareStatus Indicator
Alarm Indicators
Network Connected
Network Not Connected
Network Status Indicator
Active AirPlayStream Indicator
iHome App Indicator
AM and PMI ndicator
Mode and Status Display
TimeDisplay
Not connected | OFF,iPod, Radio, or Aux mode
Not connected | AirPlay mode
iW4Wi-Fi network OFF (Press & Hold Power button)
* AirPlay mode will be unavailablein Net workOFF state
Note:You may have to restart iTunes or your iOS device
beforethe iW4 is selectable as an AirPlay audio source
low signalstrength
medium signal strength
strongsignal strength
power
sync
alarmskip
alarm2alarm1presetseq nap
aux-in
networksetupstatus
12V3.5A
Quick Start
power
sync
alarmskip
alarm2alarm1presetseq nap
power
sync
alarmskip
alarm2alarm1presetseq nap
Power on your iW4Connect AC power
Removetab from bottom
of iW4 forbatter y backup
Set clock with AutoSync
1 2 3
Connect to your Wi-Finetwork
4 5 6
iW4 will automatically sync time
with your docked iPad, iPhone or iPod
outlet
12V
Network OFF
NETWORK STATUS
FRONT DISPLAY
Wi-Fi network status LED
Firmware button & status LED
Wi-Fi network setup
- Pressfor Wi-Fi Sharing with docked iOS 5.0 or later device
- Press& hold for manual network setup
Master poweris OFF
Green,solid when connec tedto a Wi-Fi network
Red,blink ing when NOTconnected to a Wi-Fi network
USB Port
(rmwareupdate)
AC Power
REAR PANEL
TOP PANEL
Aux-in - Dock iOS 5.0 or later device (verifyWi-Fi is
ON and connec tedto desired network)
- Press Network Setup button on iW4
- Select‘Allow’ on pop-up message
- Keep reading for additional setup methods
- Connect AC power adaptor,pull tab
from the backup battery compartment
on bottom of unit
- Dock your iPad, iPhone,or iPod and press
toenjoy your favorite music
- Press the Mode button to select AirPlay,
iPod, FM Radio, and AUX-in modes
- Press & hold Alarm 1 & 2 buttons to set your
desired wake preferences
Play, charge, sleep & wake
Dierentregions of the world use dierent FM radio frequency steps
and ranges (default is USA).To adjust settings for your region (USA,
EUROPE, JAPAN,AUSTRALIA, or CHINA):
- Make sure the unit is OFF. Press and holde the MODE button for 5
seconds until“RADIO XXX” appears in the lower part of the display.
- Pressthe SET + | - buttons to select your region.
- Pressthe MODE button again to conrm your selection and exit the
radio frequency mode settings.
Alarm 1 & 2 Buttons
- Pressto preview programmed alarm time
- Press& hold to manually set alarm time, repeat, source, and volume
- Presstwice to turn the alarm On or O
Set + | -
Mode Select
- Pressfor AirPlay, iPod, FM Radio, and Aux-in modes
Bedtime | Sleep Timer
- Pressto activate an adjustable count down timer
to enjoy your favoritemusic as you fall asleep
Music Control Buttons
- Pressto control music playback of your docked
iPad|iPhone|iPodor connected AirPlay device
EQ Control
- Pressto enter EQ adjust mode, then press “+”or “-”
adjust each setting *Powermust be ON
Clock Set | Sync
- Pressto sync time with docked iOS device
- Press& hold to manually set time
* iW4 will automatically sync time with a docked iOS deviceby default
** PressALARM 1 or ALARM 2 button during time set for 12|24 hour
Wakeup | Alarm Skip Button
- Pressto stop and reset a sounding alarm
- Pressto skip the nex t pending programmedalarm time without
turning o for holidays or when youwakeup before the alarm
- Press& hold to adjust the ‘Gentle Wake’timer (O, 1-10 minutes)
FM Radio Presets
- Pressto cycle through programmed radio preset stations (P1-6)
- Programyour favorite stations by selecting the preset number you
want to change, then press & hold again beforeadjusting the station,
and then press one nal time to conrm yourselec tion
Quick Nap Alarm
- Pressto activate and adjust a count down timer for a power nap
Snooze | Dimmer
- Pressto adjust the display brightness
- Pressto delay a sounding alarm
- Press& hold to adjust snooze timer
FM Radio Band Region Selection
Volume Up | Down
- Pressto adjust the volume of the iW4 speakers
Power | Alarm Reset Button
- Pressto power On the iW4 speaker system
- Pressto stop and reset a sounding alarm
- Pressto exit Network Setup mode
- Press& hold to turn o Wi-Fi and reset the iW4
- Pressto adjust time, alarms, radio, eq, and device settings
LEARN MORE
SCAN
FM antenna
Turn over for more information
Turn over for more information
Turn over for more information
Using an iOS 5.0 or later device:
Option B - Manually Connecting with the iHome Set app
If you have an iPod touch, iPhone, or iPad with iOS 4.2 or later, we recommend that you use
our free iHome Set app to easily rename your iW4 speaker and congure network settings.
Using an iHome Set:
Follow this method if you have a wired home network or prefer the performance of a direct
connection with router.
Using a Ethernet cable (not provided):
1. Press & hold the Power button (4 seconds) to power OFF the iW4 network.
2. Connect an ethernet cable to the iW4 rear ethernet port and to your router (or network).
3. Press & hold the Power button (4 seconds) a second time to power ON the iW4 network and establish a direct
ethernet connection.
Option C - Connecting directly via Ethernet
Success!
Enjoy AirPlay, iPod (docked), FMradio, and Aux-in modes:
1. Press Mode button for AirPlay, iPod, FM Radio,and Aux-in audio content.
2. Press to control your music content and press to adjust the volume of the iW4 speakers.
Set display & clock preferences:
PANDORA® , iHeartRadio®, and TuneIn® - I nternetradio music apps
Turn your iW4 system into an internet radio when youuse AirPlay audio streaming
with your favorite iOS music apps.
Remote App - Control iTunes playback anywhere in the house
Download Apple’s Remote app free from the App Store to your iOS device and control your iTunes library and AirPlay
speakers wirelessly when connected to the same Wi-Finetwork.
iHome+apps - iW4 works with a suite of iHome apps available on the app store
iHome Set - control iW4 features like network setup, EQ,time, alarms, and rmware updates.
iHome Sleep - wake to custom alarms and music playlists.
Connected Not Connected Network Problem?
If the NetworkStatus LED is green, the iW4 is
connected to a network
power
sync
alarmskip
alarm2alarm1presetseq nap
aux-in
networksetupstatus
12V3.5A
networksetup
status
If the NetworkStatus LED is ashing red, the iW4 is not
connected to a network because,either:
-The iW4 has not been connected to a Wi-Fi network
-There is a problem with your Wi-Fi network
- Or,the iW4 is out of range
Reset the iW4 Network:
- Press & hold the Powerbutton (4 sec.) to turn networkOFF.
- Press & hold the Powerbutton again to reactivate the network.
- Visit our website for additional instructions and support.
power
sync
alarmskip
alarm2alarm1presetseq nap
power
sync
alarmskip
alarm2alarm1presetseq nap
aux-in
networksetupstatus
12V3.5A
networksetup
status
power
sync
alarmskip
alarm2alarm1presetseq nap
power
sync
alarmskip
alarm2alarm1presetseq nap
aux-in
networksetupstatus
12V3.5A