IKEA LAGAN User manual

LAGAN
AU
“AU”


ENGLISH 4
Please refer to the last page
of this manual for the full list
of IKEA appointed Authorized
Service Centre and relative
national phone numbers.

4
Before rst use
Your safety and that of others is
paramount.
Remove cardboard protection
pieces, protective lm and
adhesive labels from accessories.
Check the appliance for any
transport damage.
To avoid any damage do
not place any weights on the
appliance. Do not expose the
appliance to atmospheric agents.
This manual and the appliance
itself provide important safety
warnings, to be read and
observed at all times.
This is the attention symbol,
pertaining to safety, which
alerts users to potential risks to
themselves and others.
All safety warnings are preceded
by the attention symbol and the
following terms:
DANGER: indicates a
hazardous situation which, if
not avoided, will cause serious
injury.
WARNING: Indicates a
hazardous situation which, if
not avoided, could cause serious
injury.
All safety warnings give specic
details of the potential danger/
warning present and indicate how
to reduce risk of injury, damage
and electric shock resulting from
improper use of the appliance.
Carefully observe the following
instructions.
Precautions and general
recommendations
• The electrical installation and
the electrical connection must
be carried out by a qualied
technician according to the
manufacturer’s instructions
and in compliance with the
local safety regulations. Do not
repair or replace any part of
the appliance unless specically
stated in the user manual.
• The appliance must be
disconnected from the power
supply before carrying out any
installation work.
WARNING: Failure to install
the screws or xing device in
accordance with these instructions
may result in electrical hazards.
Safety Information
Safety Information 4
Use 7
Product description 8
Control panel 8
Cleaning and maintenance 8
What to do if ... 10
Technical data 11
Environmental concerns 12
IKEA GUARANTEE 13
Contents
GB
ENGLISH

5
ENGLISH
• Earthing of the appliance is
compulsory. (Not possible for
class II hoods identied by the
symbol on the dataplate).
• Do not pull the power supply
cable in order to unplug the
appliance.
• The electrical components must
not be accessible to the user
after installation.
• Do not touch the appliance
with any wet part of the body
and do not operate it when
barefoot.
• This appliance can be used
by children aged from 8 years
and above and persons with
reduced physical, sensory or
mental capabilities or lack of
experience and knowledge
if they have been given
supervision or instruction
concerning use of the appliance
in a safe way and understand
the hazards involved. Children
shall not play with the
appliance. Cleaning and user
maintenance shall not be made
by children without supervision.
• All other maintenance services
must be carried out by a
specialised technician.
• When drilling through the wall
pay attention not to damage
electric connections and/or
pipes.
• Air vents must always discharge
to the outside.
• The manufacturer rejects all
responsibilities for any damage
caused by improper use or
wrong settings.
• Appropriate maintenance
and cleaning ensure the good
working order and the best
performance of the appliance.
Regularly clean all stubborn
surface dirt to avoid grease
build up. Remove and clean
or change the lter regularly.
This must be completed in
accordance with the “Cleaning
and maintenance” instructions
provided.
• Never ame cook food (ambé)
under the appliance. Using free
ames might cause re.
• Failure to observe the
instructions for cleaning the
hood and replacing the lters
may result in a re.
• Exhaust air must not be vented
through a ue used for removal
of fumes produced by gas
combustion appliances or other
combustible materials, but must
have a separate outlet. All
national regulations governing
extraction of fumes must be
observed.
• There shall be adequate
ventilation if the hood is being
used at the same time as other
appliances using gas or other
combustible materials. The
negative pressure of the room

6
ENGLISH
must not exceed 4 Pa (4x 10-5
bars). For this reason ensure
that the room is well ventilated.
In case of doubts, please consult
an autorized service assitance
center or similar qualied
person.
• Do not leave frying pans
unattended when frying, as the
frying oil may catch re.
• Before touching the light bulbs,
ensure that they are cold.
• Do not use or leave the hood
without the light bulb correctly
tted, as this may cause electric
shock.
• The hood is not a work surface,
therefore do not place any
objects on top of it or overload
it.
• During all installation and
maintenance operations wear
appropriate working gloves.
• This appliance is not suitable for
outdoor use.
WARNING: when the hob is in
use, accessible parts of the
hood may become hot.
Installation and connection
In the event of problems, contact
the Authorized Service Centre. To
prevent any damage, only remove
the appliance from its packaging
at the time of installation.
Preparing for installation
WARNING: this is a heavy
product; the hood should only
be lifted and installed by two or
more people.
The minimum distance between
the hob and the bottom part of the
hood must not be less than 65 cm
for burning gas or other fuels and
50cm for electric cookers.
Before installation also check the
minimum distances stated in the
manual of the cooker.
If the installation instructions for the
cooker specify a greater distance
between cooker and hood, this
distance must be observed.
Electrical connection
Make sure the power voltage
specied on the appliance rating
plate is the same as the mains
voltage.
This information can be found
on the inside of the hood, under
the grease lter. Power cable
replacement (type H05 VV-F)
must be carried out by a qualied
electrician. Contact an authorized
service centre.
If the hood is tted with an electric
plug, connect the plug to a socket
complying with current regulations,
located in an accessible place.

7
ENGLISH
The hood has been designed to be installed and
used either as a “Extraction installation”, or as a
“Recirculation installation”.
Extraction installation (see symbol in
installation booklet)
Cooking steam is sucked and channelled
outside the house through a discharge duct (not
supplied), tted to the hood steam outlet.
Ensure that the discharge duct is correctly tted
to the air outlet, unit using an appropriate
connection system.
Important: If already installed, remove the
charcoal lter/s.
Recirculation installation (see symbol in
installation booklet)
The air is ltered through one or more the
charcoal lters, and then resent into room.
Important: Ensure appropriate air circulation
around the hood.
Important: If the hood is supplied without
charcoal lters, these must be tted before the
hood can be used. Filters are available in IKEA
shops.
The hood should be installed away from
particularly dirty areas, windows, doors and heat
sources.
The accessories for wall xing are not included
because walls made of different materials require
different types of xing accessories. Use xing
systems suitable for the walls of your home and
the weight of the appliance. For more details,
contact a specialized dealer.
Keep this booklet for future consultation.
WARNING: if no plug is tted
(direct wiring to the mains), or
if the socket is not located in an
accessible place, a qualied
electrician should install a
standardised double pole power
switch that will enable complete
isolation from the mains in case of
category III overvoltage conditions,
in accordance with wiring rules.
Use

8
ENGLISH
Product description
1 Control Panel.
2 Grease lter.
3 Lighting unit.
Control panel
WARNING:
-Never use steam cleaning equipment.
-Disconnect the appliance from the power
supply.
IMPORTANT: do not use corrosive or abrasive
detergents. If any of these products accidentally
comes into contact with the appliance, clean
immediately with a damp cloth.
• Clean the surfaces with a damp cloth. If it is
very dirty, add a few drops of washing up
detergent to the water. Finish off with a dry
cloth.
IMPORTANT: do not use abrasive sponges or
metallic scrapers or scourers. Over time, these
can ruin the surface.
Cleaning and maintenance
A To switch ON the light, push the button
B
ON/OFF button / Extraction power 1
selection button.
C
Extraction power 2 selection button.
D
Extraction power 3 selection button.
• Use detergents specically designed for
cleaning the appliance and follow the
manufacturer instructions.
IMPORTANT: clean the lters at least monthly to
remove any oil or grease residuals.
To clean the grease lter
The metal grease lter has an unlimited life
and must be washed once a month by hand or
dishwasher at low temperature and with a short
cycle. With cleaning in a dishwasher the grease
lter may become dull; this does not effect its
ltering capacity.
32
1
AB C D

9
ENGLISH
Grease lter maintenance:
1. Unplug the appliance or disconnect the
power supply.
2. Remove the grease lters: pull the spring
release handle, then remove the lter
downwards.
3. After cleaning the grease lter, remount in
reverse order ensuring the entire extraction
surface is covered.
Charcoal lter maintenance (if the hood is
installed in recirculation installation)
1. Pull out the plug or disconnect the power
supply.
2. Remove the grease lter
3. If the carbon lters are already tted (two
lters that cover the protective grilles for the
motor impeller) and have to be replaced, turn
the central handle anti-clockwise to unlock
them.
4. Open the two lter shells
5. Pull out the two circular mats
6. Proceed in reverse order to t the new lters.
7. Ret the grease lters.
Unlike traditional charcoal lters, this charcoal
lter can be washed and reactivated.
Care and cleaning long life Charcoal lter
• The anti-odour lter shall be washed and
regenerated every 3-4 months (or more
frequently if the hood is subject to intensive
use), up to a Max. of 8 regeneration cycles
(in case of particularly intensive use it is
recommended that you do not exceed 5
cycles).
Regeneration procedure:
• Wash in the dishwasher at a MAX temperature
of 70° or hand wash in hot water without using
abrasive sponges (do not use detergents!)
• Dry in the oven at a MAX temperature of
70° for 2 hours or dry at room temperature,
standing the lter in a vertical position to
facilitate drainage.
Lamp maintenance
Disconnect the hood from the power supply.
Open the extractor grille or remove the self-
supporting grease lter.
Replace the damaged lamp. Use E14 3W max
LED lamps only.
Ret the extractor grille or grease lter.
IMPORTANT: make sure you don’t touch the
lamp with your bare hands.
Lamp Power
(W)
Socket Voltage
(V)
Dimension
(mm)
ILCOS D Code
3E 14 220/240 36 x 102 DRBB/C-3-220-
240-E14-35/102

10
ENGLISH
Before contacting the Authorized Service
Centre:
Switch the appliance on again to see if the
problem has disappeared. If not, switch it off
again and repeat the operation after an hour.
If your appliance still does not work properly
after carrying out the checks listed in the
troubleshooting guide and switching the
appliance on again, contact the Authorized
Service Centre, clearly explaining the problem
and specifying:
Problem Possible cause Solution
The appliance does not
work
There is no mains
electrical power
Check for the presence of mains electrical
power.
Turn off the appliance and restart it to see
if the faults persists.
The appliance is not
connected to the electrical
supply
Check if the appliance is connected to the
electrical supply.
Turn off the appliance and restart it to see
if the faults persists.
The hood’s suction level is
not enough
The suction speed is too
low
Check the suction speed and adjust as
necessary.
The grease lters are dirty Check that the lters are clean
If not, clean the lters in the dishwasher.
The anti-odors lters are
dirty
Check that the anti-odour lters are
properly washed as recommended
The air vents ar e
obstructed
Check the air vents for any obstructions
and remove as necessary.
The light does not work The BULB is broken Check the light bulb and replace it if
necessary.
The light bulb is not
correctly tted
Check that the light bulb has been
correctly tted. If not, t the light bulb in
right way.
• the type of fault;
• the model;
• the type and serial number of the appliance
(given on the rating plate);
• the Service number (the number after the
word SERVICE on the rating plate inside the
appliance).
What to do if ...

11
ENGLISH
Technical data
The technical information is situated in the rating
plate on the internal side of the appliance.
Type of product Wall mounted hood
Dimensions
Width mm 600
Depth mm 510
Total height in extraction installation version min-max mm 130
Total height in recirculation installation version min-max mm 130
Total power W 14 6
Lamps info
Type LED Bulb
Number & Power W 2x3W
Socket W 14
Installation minimum height - gas hob mm 650
Installation minimum height - elec hob mm 500
Product Weight Kg 6,4
Additional Product Information compliant to commission regulation (EU) No 66/2014
Model identier
LAGAN 20388967
LAGAN 20392323
LAGAN 70392194
LAGAN 60393962
Annual Energy Consumption kWh/a 64,2
Time increase factor 1,4
Fluid Dynamic Efciency % 15,5
Energy Efciency Index 77,3
Measured air ow rate at best efciency point m³/h 175
Measured air pressure at best efciency point Pa 374
Maximum air ow m³/h 320
Measured electric power input at best efciency point W117
Nominal power of the lighting system W 6
Average illumination of the lighting system on the cooking surface lux 126
Power consumption in standby mode W na
Power consumption off mode W na
A-waighted Sound Power Emission at maximum speed dB(A) 73

12
ENGLISH
Environmental concerns
Disposal of packing
The packing material is 100% recyclable and is
marked with the recycle symbol . The various
parts of the packing must therefore be disposed
of responsibly and in full compliance with local
authority regulations governing waste disposal.
Scrapping the product
- This appliance is marked in compliance
with European Directive 2012/19/EU, Waste
Electrical and Electronic Equipment (WEEE).
- By ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the environment
and human health, which could otherwise be
caused by inappropriate waste handling of
this product.
The symbol on the product or on the
accompanying documentation indicates that
it should not be treated as domestic waste but
must be taken to an appropriate collection centre
for the recycling of electrical and electronic
equipment.
Scrapping of household appliances
Electrical connection for Australia
Power Cord and Plug: Declared Article –
Mandatory Approval Applies:
Current Australian Approval Certicates will
need to be forwarded, showing compliance with
applicable Australian Standards, as noted below.
Plug to have insulated pins. Plug and Cord
to have approval marking, as required by the
relevant Approval Certicate
• AS/NZS 3112: 2004 with Amendment 1,
for Plug
• AS 3191: 2008, for Cord, or;
• ‘HAR’ Certication, for Cord
• This appliance is manufactured with
recyclable or reusable materials. Dispose of
it in accordance with local waste disposal
regulations. Before scrapping, cut off the
power supply cable.
• For further information on the treatment,
recovery and recycling of household electrical
appliances, contact your competent local
authority, the collection service for household
waste or the store where you purchased the
appliance.
Energy saving tips
• Switch ON the hood at minimum speed when
you start cooking and kept it running for few
minutes after cooking is nished.
• Increase the speed only in case of large
amount of smoke and vapour and use boost
speed(s) only in extreme situations.
• Replace the charcoal lter(s) when necessary
to maintain a good odour reduction efciency.
• Clean the grease lter(s) when necessary to
maintain a good grease lter efciency.
• Use the maximum diameter of the ducting
system indicated in this manual to optimize
efciency and minimize noise.

13
ENGLISH
How long is the IKEA guarantee valid?
This guarantee is valid for ve years from the
original date of purchase of your appliance at
IKEA Pty Ltd,
ABN 84 006 270 757 or at Cebas Pty Ltd, ABN
15 009 156 003. The original sales receipt, is
required as proof of purchase. If service work is
carried out under guarantee, this will not extend
the guarantee period for the appliance.
Who will execute the service?
IKEA Authorized Service Centre will provide the
service through its own service operations or
Authorized Service Centre network.
Contact IKEA for further information.
• If you encounter any trouble with theappliance
and wish to register a servicecall or make
a claim, please refer toww.ikea.com.au for
your local store aftersales customer service
center phonenumber, online email and
opening timesor refer to the phone numbers
shownbelow.
The principal address and contact details in
Australia are:
IKEA Authorized Service Centre at
www.IKEA.com.au or
• For Queensland, New South Wales
andVictorian customers please contact:
IKEA Pty Ltd
IKEA Service OfceL1 Clock Tower, 630 Princes
HighwayTempe, NSW 2044
Victoria:(03) 8523 2154
New South Wales: (02) 8020 6641
Queensland: (07) 3380 6800
IKEA Perth: (08) 9201 4532
IKEA Adelaide: (08) 8154 4532
• For Western Australian and SouthAustralian
cutomers please contact:
Cebas Pty Ltd
8c Sunray Drive,
Innaloo WA 6018 Australian
IKEA Perth: (08) 9201 4532
IKEA Adelaide: (08)8154 4532
What does this guarantee cover?
The guarantee covers applicable faults of the
appliance, which have been caused by faulty
construction or material faults from the date
of purchase from IKEA. This guarantee applies
IKEA GUARANTEE
to domestic use only. The products have been
designed and tested for domestic purposes only
and this guarantee does not cover damage
arising from use of the Product in a commercial
environment. The exceptions are specied under
the headline “What is not covered under this
guarantee?” Within the guarantee period, the
costs to remedy the fault e.g. repairs, parts,
labour and travel will be covered, provided that
the appliance is accessible for repair without
special expenditure. Replaced parts become the
property of IKEA.
The guarantee exists only if the appliance
complies and is installed in accordance with:
• The technical specications.
• The Assembly Instructions and usermanual
Safety Information.
IKEA’s guarantee is subject to Australian
Consumer Law - see Schedule 2 to Competition
and Consumer Act, 2010. This guarantee is in
addition to (and does not exclude, restrict or
modify in any way) any non-excludable statutory
warranties in Australia.
What will IKEA do to correct the problem?
IKEA appointed service provider will examine
the product and decide, at its sole discretion, if
it is covered under this guarantee. If considered
covered, IKEA service provider or its authorized
service partner through its own service
operations, will then, at its sole discretion, either
repair the defective product or replace it with the
same or a comparable product.
What is not covered under this guarantee?
• What is not covered under this guarantee?
• Normal wear and tear.
• Deliberate or negligent damage,damage
caused by failure to observeoperating and
maintenance instructions,incorrect installation
or by connectionto the wrong voltage, damage
causedby chemical or electrochemical
reaction,rust, abrasion or scratching, corrosion
orwater damage including but not limitedto
damage caused by excessive lime inthe
water supply, damage caused byabnormal
environmental conditions.
• Damage caused from the use of theappliance

14
ENGLISH
in a manner other thanthe use for which it was
specicallydesigned.
• Damage caused by power outages,electrical
power surge or impropersupply voltage
via connection to SupplyAuthority mains or
alternative supplysystems.
• Consumable parts including batteriesand
lamps, removable wire, glass andplastic trays
and other accessories.
• Internal or external damage as a resultof
excessive use of cleaning products orcleaning
agents.
• Non-functional and decorative partswhich
do not affect normal use of theappliance,
including any scratches andpossible color
differences.
• Accidental damage or blockages causedby
foreign objects, eg. coins, underwires,nails,
buttons or jewellery, or substancesand
cleaning or unblocking of lters,drainage
systems or soap drawers
• Damage caused by vermin, insects orpets.
• Note – internal or external abinettransport
damage must be reportedwithin 7 days of
purchase date.
• Damage to the following parts: ceramicglass,
accessories, crockery and cutlerybaskets, feed
and drainage pipes, seals,lamps and lamp
covers, screens, knobs,casings and parts of
casings. Unless suchdamages can be proved to
have been caused by production faults.
• Cases where no fault could be foundduring a
technician’s visit.
• Any consequential loss due to appliancefailure.
• Repairs not carried out by our
appointedservice providers and/or an
authorizedservice contractual partner or where
nonoriginal parts have been used.
• Repairs to parts or systems caused
byunauthorized modications made
toappliance.
• Repairs caused by installation which isfaulty or
not according to specication.
• Problems caused by incorrect orinadequate
venting of the appliance.
• The use of the appliance in a nondomestic
environment i.e. professionaluse.
• Transportation damages. If a
customertransports the product to his home
oranother address, IKEA is not liable forany
damage that may occur duringtransport.
However, if IKEA delivers the productto the
customer’s delivery address, thendamage to
the product that occursduring this delivery will
be covered byIKEA.
• Cost for carrying out the initialinstallation
of the IKEA appliance.However, if an IKEA
appointedAuthorized Service Centre or
its authorizedservice partner repairs or
replacesthe appliance under the terms of
thisguarantee, the Authorized Service Centreor
its authorized service partner willreinstall the
repaired appliance or installthe replacement,
if necessary.
• The benets conferred by this expresswarranty
are in addition to all otherconditions,
warranties, guarantees, rightsand remedies
expressed or impliedby the Trade Practices
Act and similarState and Territory laws and all
otherobligations and liabilities on the partof
the manufacturer or supplier andnothing
contained herein shall restrict or modify such
rights, remedies, obligations or liabilities.
How country law applies?
Our goods come with guarantees that Our goods
come with guarantees that cannot be excluded
under the Australian Consumer Law (ACL).
You are entitled to a replacement or refund for a
major failure and for compensation for any other
reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a
major failure.
This guarantee is not intended in any way to limit
or exclude such rights and remedies that you may
have under law.
You can nd out more information about
the Australian Consumer Law on the ACCC
website: www.accc.gov.au
Area of validity
The IKEA guarantee applies only to products
purchased and installed in AUSTRALIA .

15
ENGLISH
What you must do to make a claim under the
guarantee
To make a claim under the guarantee contact
IKEA Authorized Service Centre at the above
address, the IKEA catalogue or refer to www.
ikea.com.au for your local store customer service
phone number, online email and opening times.
Please describe the problem that you are facing
with the appliance in detail along with your
product article number (8 digit code) and date of
purchase at the time of call registration.
Please do not hesitate to contact the dedicated
Authorized Service Centre for IKEA appliances
to:
1. Make a service request under thisguarantee.
2. Ask for clarication on installation of theIKEA
appliance in the dedicated IKEAkitchen
furniture.
3. Ask for clarication on user manualcontents
and specications of the IKEAappliance.
To ensure that we provide you with the best
assistance, please read carefully the Assembly
Instructions and/or the User Manual section of
this booklet before contacting us.
How to reach if you need our service
The IKEA Authorized Service Centre will assist
you on the phone with basic trouble shooting
for your appliance at the time of warranty call
registration.
Please refer to the IKEA catalogue or www.ikea.
com.au or to below phone numbers and select
your local store .
Victoria: (03) 8523 2154
New South Wales: (02) 8020 6641
Queensland: (07) 3380 6800
IKEA Perth: (08) 9201 4532
IKEA Adelaide: (08) 8154 4532u
Please describe the problem that you are
facing with the appliance in detail along with
your product model number, serial number,
date of purchase at the time of call registration.
Please also always refer to the IKEA article
number (8 digit code) and 12 digit service
number placed on the rating plate of your
appliance.
SAVE THE SALES RECEIPT!
Kindly keep all these details and original invoice
of purchase handy during the service technician’s
visit to enable him to carry out the job. It is your
proof of purchase and required for the guarantee
to apply.

© Inter IKEA Systems B.V. 2018 23232 AA-2046074-2
LIB0146375 AUS Ed.05/18
Other manuals for LAGAN
70
Table of contents
Other IKEA Ventilation Hood manuals

IKEA
IKEA W10502581D User manual

IKEA
IKEA DATID Product information sheet

IKEA
IKEA IHW6362VM0 Product information sheet

IKEA
IKEA UTDRAG User manual

IKEA
IKEA BF570 User manual

IKEA
IKEA OMNEJD User manual

IKEA
IKEA HARMONISK User manual

IKEA
IKEA W10258591A Product information sheet

IKEA
IKEA SVÄVANDE User manual

IKEA
IKEA Rytmisk User manual

IKEA
IKEA UTDRAG User manual

IKEA
IKEA LAGAN User manual

IKEA
IKEA LUFTIG User manual

IKEA
IKEA VINSTGIVANDE User manual

IKEA
IKEA MATÄLSKARE User manual

IKEA
IKEA LUFTIG HW400 User manual

IKEA
IKEA IH5303SS0 Product information sheet

IKEA
IKEA IHW7302YS0 User manual

IKEA
IKEA LAGAN BF275 Manual

IKEA
IKEA LUFTIG User manual