
High Resolution Frame Shutter Camera
n
ll Adoption of square pixel CCD: This camera uses image pick-up
elements that are most appropriate for the image perception of the
device. The pitch of the picture elements are aligned in the same
dimensions, vertically and horizontally, correction of the dimensions at
the picture processing side is not necessary.
ll Frame shutter function: This camera can take in full-frame pictures
even when using an electronics shutter. So high-resolution picture
processing in production and inspection lines can be realized.
ll Random trigger function: The shutter start time can be controlled
with external trigger signals, thus enabling images to be input at the
desired timing. Fast moving subjects can be caught at the specified
positions on the monitor, thus realizing higher accuracy image
processing by combining the frame shutter.
ll Sync reset function: This camera has a reset mode, inwhich the
vertical synchronizing signals are reset by trigger signals; and a non-
reset mode, in which the period of the vertical synchronization signals
are maintained at a given length. You can choose an appropriate
mode according to your system.
ll Adoption of high sensitivity CCD sensor: Due to adapt of the wide
wave sensitivity CCD ( cover the near infrared area), this camera is very
effectively at low light condition and at infrared light condition.
ll Automatic switching of internal synchronization/external
synchronization: Stable external synchronization by HD/VD, this
camera has an automatic switching system whereby external
synchronization is given priority.
ll Flange focal length adjustment mechanism: It is equipped with a
flange focal length adjustment mechanism. This means deviations in
focus, due to lenses being out of focus, can be adjusted.
ll Durabledesign: This camera has a higher resistance to strong
vibration and impact than ordinary monitoring cameras. So this camera
provides stable operation and high reliability even in an environment
where it is subject to vibration or impact from automatic machinery.
ll Compact and light weight: A reduction in size and weight are realized
by integrating the power source, this enable easier selection of a
mounting place.
ll RS-232C: It is available for remote control use.
n
ll Rating
Pick-up device Interline Transfer (IT) CCD
Image size 2/3-inch (9.0mm x 6.7mm)
Effective pixels 1392 x 1040( H X V )
Pixel size 6.45 x 6.45 µm ( H X V )
Output signal model Analog output: 12Hz non-interlace
With synchronization
Digital output: 12Hz non-interlace
(Sync signal:VD, HD, CLK
output simultaneously)
Normal: EIA-644 standard 10bit parallel
(RS-422A is option)
Scanning mode Non-interlace 1/12 sec.
Synchronization method Internal/External (Autoswitching)
Synchronizationfrequency fh = 13.726 KHz
fv = 12.85Hz
Pixel clock 24.57MHz
External input synchronization TTL level
Video outputs Analog: VS 1.0Vp-p/75Ω
Digital: EIA-644 standard (RS-422A:
Option)
CLK (24.57MHz): HD,VD,DATA
Power source DC 12V (11 ~ 16V)
Power consumption Less than 4W(without digital cable)
Less than 5W(with digital cable 3m)
Lens mount C-mount
Light-axis accuracy ±0.1mm
Optical filter Dust proof glass (dust prevention,
Detachable)
IR cut filter (option)
Dimensions (WHD) 46 x 42 x 84mm
Weight Approx. 200g ( 0.4 lbs)
Design and specifications are subject to change without notice.
Control RS-232C communication control possible.
Connector Analog video OUT: BNC
Digital OUT: Half pitch 36pin
DC IN/Sync: 12pin (HR10A-10P-12S)
Remote: 6pin (HR10A-7P-6P)
Operating temperature -5°C ~ +50°C
Humidity 30 ~ 75% relative humidity
(no moisture condensation shall over)
Storage temperature -20°C ~ +60°C
Storage humidity 30 ~ 85% relative humidity
(no moisture condensation shall over)
ll Performance
Resolution (H) 1392pixels (V) 1040 lines
S/N ratio More than 50dB (AGC off, Gamma=1)
Sensitivity Standard illumination: approx 120 lx/f11
(gain 0dB, without IR Cut filter, Shutter Off)
Minimum illumination: 0.12 lx/f1.4
(gain +24dB, without IR Cut filter, Shutter off
Graduation 10 bit
Gain AGC ON/OFF and manual adjustment
Gamma ON (γ=0.45) / OFF (γ= 1) by Switch
Shutter mode Normal shutter or trigger shutter
Shutter speed
Normal: 1/12 ~ 1/7,000 sec (15 steps)
(1/12,1/500,1/700,1/900,1/1000,1/1150
1/1250,1/1400,1/1500,1/1700,1/2000,
1/2300,1/2750,1/3400,1/4600, 1/7000)
Random mode: 1/500 ~ 1/2,200 sec
(1/500,1/1000,1/1500,1/2200)
Sync reset mode Reset/Non-reset mode(trigger shutter mode)
External control RS-232C
Stability of external synchronization
Input signal frequency allowance ±100ppm
Flange back adjustment Lens mount rotate mechanism
Ikegami Electronics (U.S.A.) Inc
nn URL: http://www.ikegami.com
Headquaters 37 Brook Avenue, Maywood, NJ 07607 Phone: (201)368-9171 Fax: (201)569-1626
Westcoast office 20603 Earl Street, Torrance, CA 90503 Phone: (310)370-2400 Fax: (310)370-7131
Southwestoffice Two Dallas Communications Complex, 6309 north O'Connor Road, Suite 117, Irving, TX 75039-3510
Phone: (972)869-2363 Fax: (972)556-1057
Midwestoffice 747 Church Road, Unit C4, Elmhurst, IL 60126 Phone: (630)834-9774 Fax: (630)834-8689
Southeast office 5200 N.W. 33rd Avenue, Suite 111, Frt Lauderdale, FL 33309 Phone: (954)735-2203 Fax: (954)735-2227