IMC Frostar FR60 User guide

Page | 1
Installation, Operating and Servicing
Instructions
A34/109 R1 ECN 4825 October 2022
FROSTAR FR60 AND FR90
Please make a note of your product details for
future use:
Date Purchased: _________________________
Model Number: __________________________
Serial Number: __________________________
Dealer: ________________________________
________________________________
_______

Page | 2
CONTENTS
WARRANTY ....................................................................................................... 3
DELIVERY.......................................................................................................... 3
INTODUCTION .................................................................................................. 3
INSTALLATION .................................................................................................. 5
TURNING LED LIGHTS ON-OFF ....................... Error! Bookmark not defined.
REVERSING DIRECTION OF DOOR ................. Error! Bookmark not defined.
ELECTRICITY SUPPLY CONNECTION ............................................................ 6
COMMISSIONING ............................................................................................. 6
CHANGING THE CONTROLLER SET POINT ................................................... 7
USING YOUR BOTTLE COOLER ...................................................................... 7
CLEANING ......................................................................................................... 8
CHANGING SHELF POSITION .......................... Error! Bookmark not defined.
MAINTENANCE ................................................................................................. 9
do’s and don’ts ................................................................................................... 9
END OF LIFE DISPOSAL ................................................................................ 10
MATERIAL CONTENT ..................................................................................... 10
SPARE PARTS LIST ........................................................................................ 11
ORDERING SPARE PARTS ............................................................................ 12
FURTHER INFORMATION .............................................................................. 12

Page | 3
WARRANTY
This equipment is guaranteed by Lincat/IMC for 2 years from the date of
purchase from Lincat/IMC, or from one of its stockists, dealers or distributors.
The guarantee is limited to the replacement of faulty parts or products and
excludes any consequential loss or expense incurred by the purchaser. Defects
which arise from faulty installation, inadequate maintenance, incorrect use,
connection to the wrong electricity supply, or fair wear and tear, are not covered
by the guarantee.
The guarantee applies in this form to installations within the United Kingdom.
Export units carry 2 years “parts only” warranty.
Please observe these instructions carefully.
DELIVERY
The packaged machine consists of:
FR60 Glass Froster containing:
Small Shelves
Large Shelves
2
1
Instruction Booklet 1
Please notify both the carrier and the supplier within 24 hours of receipt if
anything is missing or damaged.
Check that the correct machine has been supplied and that the voltage, marked
on the rating plate, is suitable for the supply available. The rating plate is
located internally on the right hand side of the unit.
INTRODUCTION
The Frostar FR60 and FR90 are efficient, fast-cooling top loaders with sliding
covers suitable for underbar use. The Frostar range is designed to produce a
steady supply of chilled glasses.
The following quantity of beverage bottles/mixers can be held in each unit:
Glass Froster Capacity
(Standard Pint Glasses)
FR60 (900h x 600w x 620d) 75

Page | 4
625
606
560
LIGHT
SWITCH
REFRIGERATION
CONTROLLER
THIS GRILL MUST BE
REMOVED IN ORDER
TO CLEAN THE AIR FILTER
300
241
851
902
MAINS
CABLE
Frostar FR60 Dimensions:
Frostar FR60 Dimensions:
The internal dimensions of the FR60 are 550mm high, by 526mm wide, by
500mm deep.

Page | 5
INSTALLATION
For the Installer
These Instructions contain important information designed to help the user
obtain the maximum benefit from their investment in a Lincat/IMC Mistral Bottle
Cooler.
Please read them carefully before starting work, and consult with the supplier in
the event of any queries.
Be sure to leave this Instruction Manual with the user after installation of the
machine is complete.
Procedure
WARNING
The following table shows the weight and the minimum quantity of
people required to lift each unit:
Glass Froster Net Weight Quantity of
People
FR60 63.5 kg (max) 4
Install the unit on a flat and level floor.
Allowing space for ventilation at the front, back and sides.
Do not install the unit close to a heat source such as a radiator or a warm air
outlet. Ensure that the unit is standing level by adjusting the feet on the base of
the unit.
If the cabinet has been stored on its front, back, or sides during transit, stand
the cabinet upright for a minimum of two hours before starting. This will avoid
damage to the compressor.
The unit has an automatic defrost cycle and evaporates all the condensate
water without the need for a drainage system.

Page | 6
.
ELECTRICITY SUPPLY CONNECTION
Position the unit in the chosen site. The electricity supply connection should be
made to a power outlet socket or isolator mounted on the wall close to the
machine. This socket or isolator must be accessible once the machine is
installed. Before connecting, check that the voltage shown on the rating label is
correct for the electricity supply you have available. If the plug does not fit your
sockets or a longer lead is required, changes must be made by an approved
electrician.
NOTE: The plug is fitted with a 10amp fuse.
The plug fuse cover must be refitted when changing the fuse. In the event of
losing the fuse cover the plug must NOT be used until a replacement fuse cover
has been obtained and fitted or the plug replaced.
WARNING: This machine must be earthed
Should the supply cord become damaged then a replacement must be fitted by
an approved electrician. The IET Codes of Practice must be observed.
The wires in the mains lead are coloured in accordance with the following code:
Green and yellow Earth
Blue Neutral
Brown Live
COMMISSIONING
Before using a bottle cooler for the first time, the interior should be wiped out
with a clean damp cloth.
Allow the machine to stand for 1 hour to allow the refrigerant to settle. Plug in
and switch on at the wall socket. There is no separate switch to turn on the
machine. The compressor will start running less than one minute after the
supply is switched on.
Check that the light is working, and check the switch is operating correctly.
Run the unit empty, and check that cold air is being circulated within the
cabinet.

Page | 7
CHANGING THE CONTROLLER SET POINT
The electronic temperature controller is factory set to -12°C and will cycle the air
temperature between ±2°. The set point can be adjusted between 5°C and -12°C
by following the button sequence below:
USING YOUR GLASS FROSTER
Load the cabinet with glasses by placing them on the wire shelves, ensuring
that the glasses are standing in an upright position. Do not obstruct the air
vents inside the cabinet.
All cabinets have an electronic off-cycle defrost controller that de-ices the
evaporator for a maximum of 30 minutes every 4 hours using electric heaters.
This evaporates the condensate water without the need for a drainage
connection.
The controller also ensures that the cabinet temperature is maintained at -18°C
±2°C between automatic defrost cycles. Note that this temperature is adjustable
(refer to above section “CHANGING THE CONTROLLER SET POINT”).
1)
Use the UP and DOWN buttons, to scroll to the
desired set point temperature (min 0°C, max 10°C).
2)
-
10
Press SET button to accept.
3)
-
11
4)
Press SET button and the current set point
temperature will be displayed.
-12
Then press stand-by button to esc.
Display will revert back to current
internal air temperature.
-
11
Press SET the current SET Point will be displayed, if
Loc is displayed then the controller is locked, to
unlock press and hold the SET button for 3 seconds,
UnL will then be displayed.

Page | 8
When the unit is not going to be used for several weeks, run it for 24 hours after
emptying it, to ensure that all condensate water evaporates.
MAKING THE BEST USE OF THE CABINETS
Do not overload the cabinet. There should be a gap of at least 40mm above the
merchandise on the top shelf, and merchandise should be spaced to allow the
circulation of cooled air throughout the cabinet. Do not load the cabinet with boxed
goods as this prevents air circulation.
Do not place hot or warm goods in the cabinet. Only goods at room temperature or
less should be placed in the unit otherwise performance will be affected.
Do not run unit with the lid open, as this will cause the evaporator to ice up
preventing the unit from working efficiently.
Ensure that both the front grille cover attached to the plinth, and the air vents inside
the cabinet are always unobstructed.
CLEANING
Clean lid and surfaces as required, occasionally remove all merchandise and clean
interior surfaces with a clean damp cloth.
DO NOT USE CLEANING MATERIALS CONTAINING ABRASIVES OR BLEACHES.
In the case of heavy soiling use a mild liquid detergent. The unit can be washed on
the inside using bicarbonate of soda to remove stale smells.

Page | 9
MAINTENANCE
Warning
Never service, repair or troubleshoot a unit unless you are a professional
air conditioning / refrigeration service person. Improper servicing can lead
to serious injury or death from fire, electric shock or explosion.
Remove the front grille cover. Clean the compressor coil with a brush and vacuum
cleaner every three months or when dirty (whichever is sooner). Replace the grille
cover.
Other than regular cleaning the unit requires no maintenance by the end user. It is
recommended that the unit is serviced by a Lincat/IMC approved engineer at least
once a year.
Details of IMC Service Contracts are available on application.
DO’S AND DON’TS
Do Install on a level surface.
Do Ensure plug is accessible with the unit installed.
Do Regularly clean the condenser and compressor.
Do Rotate stock of bottles.
Don’t Sit or stand on the unit worktop.
Don’t Load with boxed goods.
Don’t Leave the doors open.
Don’t Cover the shelves with any protective materials which may obstruct air
circulation through them.
Don’t Install unit in direct sunlight.
Don’t Block the air inlet grilles.
Don’t Store food in the unit.
Don’t Place hot or warm goods in the unit.
Don’t Use the unit outside.
Don’t Use mechanical devices to accelerate the defrosting process.
Don’t Use electrical appliances inside the storage area, unless they are
recommended by the manufacturer.
Don’t Store explosive substances such as aerosol cans with flammable
propellant in the appliance.

Page | 10
END OF LIFE DISPOSAL
At the end of its useful life the unit must be disposed of correctly and safely, to
meet the requirements of EU legislation regarding the recovery of ozone depleting
substances. The unit must be sent to a specialist recovery, recycling and disposal
site that is licensed for the disposal of refrigerated equipment. Please note that the
insulation in the Mistral range does not contain any ozone depleting substances.
The refrigerant used in the Mistral M60, M90 and M135 is R290a.
Warning
The refrigerant used in this Bottle Cooler
is R290a and is Flammable
MATERIAL CONTENT
The Mistral units may contain a combination of the following materials;
Metals Stainless Steel, Mild Steel (Inc. Nickel Plated, Chrome
Plated & Zinc Plated), Aluminium and Copper.
Plastics & Rubber PVC, Nylon, Polypropylene, Polycarbonate, Polyester,
Acetate, Neoprene Rubber and Silicone Rubber.
Insulation Polystyrene, Polyurethane Foam.
Oils & Gases Ester oil, Refrigerant R290a.
Other Glass, Magnesium Oxide, electronic components.

Page | 11
SPARE PARTS LIST
Frostar FR60
Part No
Description
A12/047
A12/048
Wire Shelf (large)
Wire Shelf (small)
849407
E49/407/B
Plinth Grille Cover
(Stainless Steel)
Plinth Grille Cover
(Black Painted)
A21/011 Lock, clip & keys
G30/545 Electronic Controller
G60/348 Mains Cable
S49/175 Refrigeration Pack
J09/049 Condenser
J09/026 Evaporator
DR16 Service Drier
S/R0100
(2.0mtr)
Capillary TC60
G42/071 Compressor
G96/049
SO21
Evaporator Fan
Solenoid Valve
G50/120 LED strip
G30/544 Transformer
G45/175 Light switch
A11/264 Door Gasket

Page | 12
ORDERING SPARE PARTS
In the event that spare parts or accessories need to be ordered, please always quote
the SERIES AND SERIAL NUMBER of the machine. This is to be found on the rating
plate located near the supply cable.
For installations outside the UK please contact your supplier.
For information on IMC spares and service support (if applicable), please call Lincat
on [phone]. Alternatively, contact us via email:
Lincat Spares Desk E-mail: [e-mail]
Lincat Service Desk E-mail: servic[email protected]
Lincat Limited
Whisby Road,
Lincoln, LN6 3QZ,
United Kingdom
Tel: [phone]
E-mail: [email protected]o.uk
Website: www.Lincat.co.uk
FURTHER INFORMATION
HTTPS://LINCAT.CO.UK/BRANDS/IMC
https://www.youtube.com/watch?v=1hSfEPKi-fg