Imlab IKA lab dancer User manual

IKA®lab dancer
20000005494
lab dancer_022016

6
The appliance must only be used on a non-slip surface.
Grubby support surface diminish the stability of the appli-
ance.
When working with the shaker, the user must select and
wear his personal protective equipment according to the
mixing hazard category. Defective or inadequate protective
equipment can expose the user to the risk of squirting liquids
and projectile parts. For this reason, only closed test tubes
should be used.
The user may also be at risk if inflammable materials are used
in the shaker, or if the trigger contact pressure is too great
for glass equipment or the transmitted mechanical shaking
power causes the glass to break.
Furthermore, the shaker may only be used to shake mate-
rials or material mixtures that the user knows will not react
dangerously to the extra energy produced by the shaking.
This also applies to extra energy generated by solar radiation
during the shaking procedure.
The appliance is maintenance-free and must not be opened.
The IKA lab dancer was not designed for use in dangerous
atmospheres, for mixing dangerous substances or for use
under water.
If the appliance begins to slide, wipe the soft stand feet with
a damp cloth.
Contents
Safety instructions
Page
Safety instructions 6
Correct use 7
Unpacking 7
Commissioning 7
Maintenance and cleaning 7
Warranty 8
Technical data 8
In order to be able to use the appliance properly and safely,
every user must first read the operating instructions and
observe the safety instructions contained therein. Take care of
these operating instructions and keep them in a place where
they can be accessed by everyone.
The IKA lab dancer is a laboratory instrument which con-
forms to the international safety regulations for laboratory
instruments.
Caution: overfilling with liquid may cause the medium to
splash out.
You should therefore always use covered test tubes.
The unit is not suitable for manual operation. Observe all
pertinent safety instructions and directives, as well as work-
safety and accident-prevention regulations for laboratory use.
EN
Source language: German

7
The IKA lab dancer is designed for shaking test tubes.
Gently push the test tube into the soft attachment to start
shaking. Shaking stops as soon as you lift out the test tube.
Please unpack the device carefully and check it for damage.
It is important that any transport damage is detected when
the device is unpacked. If necessary, an inventory of the
damage should be made immediately (postal service, railway,
haulage company).
As supplied, the package contains:
The IKA lab dancer, a plug-in power supply unit and an
instruction manual.
Connect the appliance to a socket (Please refer to the infor-
mation in the ”Technical Data” section).
The IKA lab dancer is maintenance-free. It is subject only
to the natural wear and tear of components and their statis-
tical failure rate. Use only cleansing agents which have been
approved by IKA to clean IKA devices.
To remove use:
Dyes isopropyl alcohol
Constructions materials water containing tenside/
isopropyl alcohol
Cosmetics water containing tenside/
isopropyl alcohol
Foodstuffs water containing tenside
Fuels water containing tenside
For materials which are not listed, please request information
from IKA.
Wear the proper protective gloves during cleaning of the
devices. Electrical devices may not be placed in the cleansing
agent for the purpose of cleaning.
Before using another then the recommended method for
cleaning or decontamination, the user must ascertain with
the manufacturer that this method does not destroy the
instrument.
Correct use
Unpacking
Commissioning
Maintenance and cleaning

8
You have purchased an original IKA laboratory machine which
meets the highest engineering and quality standards.
In accordance with IKA warranty conditions, the warranty
period is 24 months. For claims under the warranty please
contact your local dealer. You may also send the machine direct
to our works, enclosing the delivery invoice and giving reasons
for the claim. You will be liable for freight costs.
Warranty Technical data
Plug-in power supply unit
Rated voltage VAC 100–240
Rated frequency Hz 50–60
Output voltage VDC 12
Absorbed power Wmax. 30
Output power W7.2
Power input W1.5
Drive
Speed rpm 2800
Operating time %100
Protection class II
Pollution degree 2
Overvoltage category II
Protection class acc. to EN 60529 IP 40
Ambient humidity (relative) %80
Ambient temperature °C +5..+40 (im Betrieb)
Transport temperature °C -25 ... +70
Storage temperature °C -10 ... +70
Weight kg 0.55
Installed weight (max.) kg 0.1
Test tube size (Ø) mm 30
Dimensions (Ø x H) mm 100 x 70
Type of movement orbital
Orbital diameter mm 4.5
Touchfunction yes
Subject to technical changes!