Agilent Technologies InfinityLab LC Companion Instruction Manual

Agilent Technologies
Agilent InfinityLab LC
Companion
Technical Note
This technical note describes the installation of the G7109A Agilent InfinityLab
Companion Docking Station and Touchscreen Tablet (optional) for use with the
G7108AA InfinityLab LC Companion.
Contents
Before You Start 2
Install the InfinityLab Companion Docking Station 3
Install the InfinityLab Companion Touchscreen Tablet 5
Install a non-Agilent Touchscreen Tablet 7
Electrical Interconnection 9

2
Before You Start
Hardware required
1InfinityLab Companion Docking Station (G7109A, Item 5), including Cable
Set (Items 2, 6, and 7)
2Infinity II Solvent Cabinet (sold separately, not shown)
3Optional: InfinityLab Companion Touchscreen Tablet (G7109A#250, Item 3)
4Optional: InfinityLab Companion Safety Case for (G7109A#252, Item 4)
Additionally, to enable the LC instrument to work with the InfinityLab
Companion Touchscreen Tablet, the following item is required:
•InfinityLab LC Companion USB-Dongle (G7108AA, Item 1), including USB
Adapter Cable
Preparations
•Make sure that the InfinityLab LC Companion USB-Dongle (G7108AA, sold
separately) is installed and activated for use on at least one of the modules
of your LC instrument (see Agilent InfinityLab Companion Software
Installation Technical Note D0000195).
•Make sure that the instrument on top of which the InfinityLab Docking
Station will be installed, is turned off, before starting the installation.
 
 




3
Install the InfinityLab Companion Docking Station
1Attach the docking station to the solvent cabinet.
2Fix the CAN/USB cable assembly centered with the adhesive tape along the
right side of the solvent cabinet.
The USB A / CAN connector should be on the left side.

4
3Plug the Micro-USB B power cable and the USB A/CAN cables into the ports
at the docking station. If the cables are too long at the docking station, pull
the cable assembly towards the rear through the channel.
4Plug the CAN and the USB mini-b cables into the respective ports of the
module holding the LAN connection and an activated InfinityLab LC
Companion license.

5
Install the InfinityLab Companion Touchscreen Tablet
1Insert the tablet into the Safety Case (Option #252, recommended)
OR
attach the rubber pads (included in G7109A) to the top and bottom of the
tablet.
2Press on the lid to release the slider (1.). Lift the slider up (2.).



6
3Insert the tablet into the bottom of the docking station.
4While pressing the release button, press the slider down to fix the tablet in
the docking station.
5Rotate the slider and tablet to achieve either portrait or landscape mode.
6Connect the curved end of the micro-USB power connector to the tablet.
7Power on the instrument.
8Power on the tablet.

7
Install a non-Agilent Touchscreen Tablet
1Attach the rubber pads included in G7109A InfinityLab Companion Docking
Station to the top and bottom of your tablet device.
2Press on the lid to release the slider (1.). Lift the slider up (2.).
3Insert the tablet into the bottom of the docking station.
NOTE
When using a device other than the InfinityLab Companion
Touchscreen Tablet, USB connectivity to the LC instrument is not
supported. In this case, a connection to the LC instrument can only
be achieved by using an existing WiFi connection.



8
4While pressing the release button, press the slider down to fix the tablet in
the docking station.
5Make sure that the tablet is attached firmly to the Docking Station.

9
Electrical Interconnection
Figure 1 Electrical interconnection
/&
6\VWHP
86%PLQL &$1
0LFUR
86%%
7DEOHW
0LFUR
86%%
86%$
&$1
3RZHU&RQYHUWHU%R[
&$186%
&RQQHFWRU.LW
'RQJOH
5HDURIWKH,QILQLW\,,0RGXOH
ZLWK&RUH3URFHVVRU%RDUG'):
'RFNLQJ
3DUWRI
6WDWLRQ

*G7108-90000*
*G7108-90000*
G7108-90000
Part Number:
G7108-90000 Rev. D
Document number:
D0000216
Edition: 07/2019
Printed in Germany
©Agilent Technologies, Inc
2017-2019
Agilent Technologies, Inc
Hewlett-Packard-Strasse 8
76337 Waldbronn, Germany