Imperial Carlyon XT50000342NSB User manual

Toilet Seat Installation Instructions
INSTRUCT13
REV140909 D/SM
Important Information:
Please check the products for transport damage and that contents are complete before
installation. Consult a qualified plumber if you have any problems installing this
product. Complaints made following installation regarding the above cannot be accepted.

Assembly Instructions
Soft Close Seat Installation
2/8
TO BE USED ON BACK
TO WALL PANS AND
STANDARD PANS
ALLEN SCREW
ALLEN SCREW
TOP FIX PACK
SPRING TOGGLE CLIP (x2)
SPRING
TOGGLE
CLIP
Fixings included:

3/8
Carefully remove the seat, tighten the allen screw fixings & replace the
cap cover.
NOTE: It is important to tighten the fixings fully.
When installing turn the hex key until it is not possible to tighten any further.
Failure to tighten fully may result in hinge movement and eventual hinge
failure over a period of prolonged usage.
This completes your assembly of the soft-close hinge.
A=B
BA
Replace the seat and using the small
hex key tighten the grub screws to
fully secure the seat into position.
Fix the allen screw into the toggle
collar and push through the hole
on the top of the toilet pan.
Push the allen screw
until the spring loaded
bar flips over.
Tighten the allen screw with
the allen key provided to
secure the top fixing bracket
to the pan.
How to intall the seat using spring toggle clip
Need to make sure that the area is clean and free
from grease.
Place the seat onto the fixings and adjust until the
seat is located in a satisfactory position.

4/8
To adjust the seat loosen screw on
underside of hinge disc and adjust seat
accordingly. Once happy with positioning
retighten screw and assemble the seat
onto the WC pan.
WING NUT
SMALL WASHER
CERAMIC
LARGE WASHER
HINGE DISK
NOTE: It is important to tighten the fixings fully.
Place the seat onto the fixings and adjust until the seat is located in a
satisfactory position.
Assembly Instructions
Tools required for installation:
Standard Hinge Seat Installations
This completes your assembly of the standard hinge.
A=B
BA

INSTALLER, PLEASE DO NOT REMOVE FROM SEAT,
THIS IS FOR THE END CUSTOMER CARE OF YOUR HANDMADE SEAT
Thank you for purchasing your Imperial toilet seat.
You have just acquired a high quality and expensive piece of furniture and are
about to put it in the most hostile environment in the house! We have been
producing these fine seats for many years and our experience is that they will
give years of pleasurable service if a few simple measure are taken to look
after them.
• You should inspect your seat regularly and apply a good quality wax
polish from time to time.
• Always use your best efforts to keep your seat clean and dry. The finish
will deteriorate and the underlying timber could become permanently
stained, if subjected to long term contact with urine or water.
• Check the underside of the ring regularly and keep wiped clean and dry.
If this is a problem that persists, you should take steps to prevent it.
• It is possible that the cause is the WC “over flushing” and splashing the
underside of the seat. You may need to consult a plumber to have a
reducing cone fitted to the bottom of the flush pipe to stop this. This
only applies to low or high level flush settings.
• It is also recommended that you always lift the seat when cleaning the
lavatory bowl. Constant knocking of the seat, with a brush, will damage
the finish, as could the chemicals used to clean the china.
• Leave the seat up if you leave chemicals in the WC bowl overnight.
• It is recommended that you do not sit or stand on the lid of your seat,
as the fittings, being made of brass, are malleable and may become
damaged. Also the stoppers on the underside of the lid may cause
damage to the top side of the seat.
• Exposing your seat to large and rapid changes in temperature or
humidity could result in splitting or warping of the timber. Be careful of
radiators close to your seat.
• On seats that are “natural”, i.e Unstained, you may find that joined
boards are of slightly different colour and there could be differences
in fading from where the seats have been stacked etc. This is perfectly
natural and as the timber ages and matures, the seat will darken and take
on an even appearance.
Seat Maintenance
5/8

1. To clean use a damp cloth only.
2. Do not use any neat chemicals and under no circumstances use any
form of acid or alkaline cleaners (such as lime-scale removers) as these will
damage the plating on the metalwork.
3. To polish, most proprietary furniture polishes are suitable.
From time to time a good quality wax can be used to bring out the full
shine in your seat.
4. Abrasive creams and powders are definitely unsuitable and should be
avoided, as should scourers.
5. Fittings (often a chrome finish) should be regularly cleaned with a damp
cloth, disinfectant and furniture polish. Avoid using any abrasive metal
polishes or chemical cleaners as these may badly damage the finish.
6. Car chrome cleaners should only be used on chrome plated fittings
- and then sparingly.
Cleaning and Care Instructions
6/8

Notes
7/8
Notes

The Imperial Bathroom Company Limited
England
www.imperial-bathooms.co.uk
Tel: [phone] Fax: [phone]
Email: [email protected]