Impex AIR-1 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
AIR-1
Retain This
Manual for
Reference
121209
ASSEMBLY &
OWNER'S
MANUAL
Deluxe Fan Bike
AIR-1
IMPEX®INC.
2801 S. Towne Ave, Pomona, CA 91766
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................…….1
IMPORTANT SAFETY NOTICES..................................................................…… 2
WARNING LABEL PLACEMENT…………………………………………………… 3
HARDWARE PACK……….....…....................................................................…… 4
ASSEMBLY INSTRUCTIONS........................................................................…… 6
EXPLODED DIAGRAM………………………………………………………………. 16
PARTS LIST...................................................................................................……17
CARE, MAINTENANCE, AND STORAGE…………………………………………. 18
OPERATING NOTES………………………………………………………………… 19
COMPUTER…………………………………………………………………………… 20
WARRANTY.................................................................................................……. 21
ORDERING PARTS.....................................................................................……..21
BEFORE YOU BEGIN
Thank you for selecting the MARCY Deluxe Fan Bike AIR-1 by IMPEX®INC. For your
safety and benefit, read this manual carefully before using the bike. As a
manufacturer, we are committed to provide you complete customer satisfaction. If you
have any questions, or find there are missing or damaged parts, we guarantee you
complete satisfaction through direct assistance from our factory. To avoid
unnecessary delays, please call our TOLL-FREE customer service number. Our
Customer Service Agents will provide immediate assistance to you.
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]
© IMPEX INC. 1

© IMPEX INC. 2
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave
children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near water
or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or
other clothing that could become caught in the machine. Running or aerobic shoes are
also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly warm
up.
11. Never operate the machine if the machine is not functioning properly.
12. Read all warnings posted on the exercise bike.
13. Inspect the exercise bike for worn or loose component prior to use. Tighten/replace any
loose or wore components prior to use.
14. Care should be taken in mounting or dismounting the exercise bike.
15. This exercise bike is for consumer and home use only.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.

WARNING LABEL PLACEMENT
The Warning Labels and Caution Label shown here have been placed on the Rear Stabilizer, Main Frame.
If the labels are missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the
labels in location shown.
© IMPEX INC. 3

HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
© IMPEX INC. 4

COMPONENTS FOR ASSEMBLY
© IMPEX INC. 5

ASSEMBLY INSTRUCTION
Tools Required For Assembling the Machine: One Crossing Wrench and Allen Wrench,
provided by manufacturer.
NOTE: It is strongly recommended that two or more people assemble this machine to
avoid possible injury.
STEP-1
A.) Do not tighten Bolts until instructed to do so.
B.) Attach the Front Stabilizer (#39) to the Main Frame (#35). Secure it with four M8 x 5/8” Allen Bolts (#5)
and four 5/8” Washers (#6).
C.) Attach the Rear Stabilizer (#55) to the Main Frame. Secure it with four M8 x 5/8” Allen Bolts (#5), and
four Ø 5/8” Washers (#6).
D.) Securely tighten all Bolts.
E.) Use the four Floor Level Adjustment Knobs (#38) to stabilize the Bike on floor.
© IMPEX INC. 6

STEP 2
A.) Connect the Upper Computer Wire (#2) from the Front Post to the Computer Wire from the
Computer (#1).
B.) Attach the Computer to the Front Post (#4). Secure it with four Computer Philips Screws (#3).
© IMPEX INC. 7

STEP 3
A.) Connect the Lower Computer Wire (#37) from Main Frame (#35) to the Upper Computer Wire (#2)
from Front Post (#4).
B.) Attach the Front Post to the Main Frame. Secure it with four M8 x 5/8” Allen Bolts (#5).
© IMPEX INC. 8

STEP 4
A.) Attach the pivot on Left Swing Handle (#30L) to the pivot on Main Frame (#35).
B.) Thread the Swing Handle Shaft (#28) though Left Swing Handle into Main Frame, and
firmly secure them together.
© IMPEX INC. 9

STEP 5
A.) Attach the Swing Handle Connecting Rod (#48) to the open bracket on the bottom of the
Left Swing Handle (#30L).
B.) Secure them together with one M8 x 1 ¾” Allen Bolt (#49) and one M8 Aircraft Nut (#50).
© IMPEX INC. 10

STEP 6
A.) Attach the pivot on Right Swing Handle (#30R) to the pivot on Main Frame (#35).
B.) Thread the Swing Handle Shaft (#28) through Right Swing Handle into Main Frame,
and firmly secure them together.
© IMPEX INC. 11

STEP-7
A.) Attach the Swing Handle Connecting Rod (#48) to the open bracket on bottom of the Right
Swing Handle (#30R).
B.) Secure them together with one M8 x 1 ¾” Allen Bolt (#49) and one M8 Aircraft Nut (#50).
© IMPEX INC. 12

STEP-8
A.) Thread the Left Pedal (#41L) counter clockwise into Left Crank (#44L).
B.) Thread the Right Pedal (41R) clockwise into Right Crank (#44R).
© IMPEX INC. 13

STEP-9
A.) Remove the three Ø 5/8” Seat Flat Washers (#32) and M8 Seat Aircraft Nut (#33) from the
Seat Pad (#31).
B.) Attach the Seat Pad to the Seat Post (#34). Secure it with the three Ø 5/8” Seat Flat
Washers (#32) and M8 Seat Aircraft Nut (#33) from the Seat Pad (#31).
© IMPEX INC. 14

STEP-10
A.) Insert the Seat Post (#34) into the opening one Main Frame (#35).
B.) Thread the Lock Knob (#63) through the hole on Seat Post to securely hold it at desired
height.
© IMPEX INC. 15

EXPLODED DIAGRAM
© IMPEX INC. 16

© IMPEX INC. 17
PARTS LIST
PART
NO. DESCRIPTION SPEC. QUANTITY
1 Computer TZ-2119 1
2 Upper Computer Wire 1
3 Computer Philips Screw 4
4 Front Post 1
5 Allen Bolt M8 x 5/8” 12
6 Washer Ø 5/8” 8
7 Hex Flange Nut M10 Zinc Plated 4
8 Locking Bolt M6 x 2 3/8” 3
9 U-shaped Plate 3
10 Lock Washer Ø ½” 4
11 Hex Nut M6 4
12 Philips Screw M6 x ½” 5
13 Hex Thin Nut M10 4
14 Fly Wheel Shaft 1
15 Axle Locking Ring Ø ¾” 4
16 Aircraft Nut M5 3
17 Bearing 6000Z 4
18 Left Cover Net 1
19 Plastic Wheel 1
20 Right Cover Net 1
21 Philips Screw M5 x 3/8” 3
22 C Ring Ø 5/8” 2
23 Transportation Roller Wheel 2
24 Roller Wheel Shaft 1
25 Foam Grip 9” Foam Grip 2
26 End Cap Ø 1 ¼” 2
27 Handle Bar Grip 4 ¾” 2
28 Swing Handle Shaft 2
29 Bearing 6903ZZ 4
30L Left Swing Handle 1
30R Right Swing Handle 1
31 Seat Pad 1
32 Seat Flat Washer Ø 5/8” 3
33 Seat Aircraft Nut M8 3
34 Seat Post 1
35 Main Frame 1
36 Computer Wire Connector 2

© IMPEX INC. 18
37 Lower Computer Wire 1
38 Floor Level Adjustment Knob 2
39 Front Stabilizer 1
40 Stabilizer End Cap 4
41L Left Pedal 1
41R Right Pedal 1
42 Nut Cap 4
43 Hex Flange Nut M10 4
44L Left Crank 1
44R Right Crank 1
45 Nylon Washer Ø 1 1/8” x ¼” 2
46 Stabilizer Leverage Knob 4
47 Leverage Knob Plastic Pad 4
48 Swing Handle Connecting Rod 2
49 Allen Bolt M8 x 1 ¾” 2
50 Aircraft Nut M8 2
51 Plastic Bushing Ø 5/8” x ½” 4
52 Sleeve Ø 7/8” x 7/8” 2
53 Sleeve 2 3/8” x 1 1/8” 1
54 Crank Connector 2
55 Rear Stabilizer 1
56 Locking Bolt M6 1
57 Philips Tapping Screw ST4.2 x ¾” 3
58 Chain Wheel Axle 1
59 Chain 1
60 Pan Head Tapping Screw ST4.2 x 2 3/8” 1
61 Pan Head Tapping Screw ST4.2 x ¾” 16
62 Left Shroud 1
63 Lock Knob 1
64 Sensor Holder 1
65 Axle Lock Ring Ø ¾” 2
66 Arc Washer Ø ¾” 1
67 Bearing 6004ZZ 4
68 Chain Plate Axle 1
69 Crank Wheel 1
70 Shroud Sleeve 1
71 Right Shroud 1
72 U-shaped Stopper 1
73 Belt 1
74 Locking Clip 2

© IMPEX INC. 19
CARE, MAINTENANCE AND STORAGE
1. Inspect and tighten all parts each time you use the machine. Replace any worn parts
immediately.
2. The bike can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use
solvents.
3. Store the bike IN-DOOR. Excess moisture and water would cause rust on the frame.
4. The Bike shall be placed at least 24 inches away from the wall or/and any other object such as
furniture to provide safe access to and passage around the machine.
5. To avoid possible injury, the help of two or more people are needed when moving the machine
around.
6. Disposal Instructions – The equipment can be safely disassembled and disposed without
unreasonable hazards. Call your local recycle agency regarding details of recycling.
7. The maximum user weight is 300 lbs.
8. Assembled Dimension: 45” x 25” x 47.5”
OPERATING NOTES
SEAT ADJUSTMENT
The seat height ranges from 29” to 41”.
Loosen and pull out the Lock Knob. Slide the Seat Post to selected scale marked on the Seat
Post, then release the Lock Knob and securely fasten the Knob to lock the Seat Post.
The seat height adjustment is in approximately 1 ½” increment.
TRANSPORT
The Bike has a pair of transport Roller Wheels on Front Stabilizer. To move, carefully tilt and
roll.