Impex CIRCUIT FITNESS AMZ-594U Installation and operating instructions

NOTE:
Please read all
instructions carefully
before using this product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
AMZ-594U
Retain This
Manual for
Reference
190701
ASSEMBLY &
OWNER'S
MANUAL
Magnetic Resistance
Upright Bike
AMZ-594U
IMPEX®INC.
2801 S. Towne Ave, Pomona, CA 91766
Tel: [phone] Fax: [phone]
www.marcypro.com
[e-mail]

© IMPEX INC. www.marcypro.com
1
TABLE OF CONTENTS
BEFORE YOU BEGIN
Thank you for selecting the CIRCUIT FITNESS Magnetic Resistance Upright Bike by
IMPEX®INC. For your safety and benefit, read this manual carefully before using the
bike. As a manufacturer, we are committed to provide you complete customer
satisfaction. If you have any questions, or find there are missing or damaged parts,
we guarantee you complete satisfaction through direct assistance from our factory. To
avoid unnecessary delays, please call our TOLL-FREE customer service number. Our
Customer Service Agents will provide immediate assistance to you.
BEFORE YOU BEGIN
1
IMPORTANT SAFETY NOTICES
2
WARNING LABEL PLACEMENT
3
HARDWARE PACK
4
COMPONENT FOR ASSEMBLY
5
IMPORTANT ASSEMBLY INSTRUCTION
6
EXPLODED DIAGRAM
11
PARTS LIST
12
CARE AND MAINTENANCE, WEIGHT CAPACITY & DIMS.
13
COMPUTER
14
EXERCISE GUIDELINES
19
WARRANTY
21
ORDERING PARTS
21
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.marcypro.com
[e-mail]

© IMPEX INC. www.marcypro.com
2
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave
children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near water
or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or
other clothing that could become caught in the machine. Running or aerobic shoes are
also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly warm
up.
11. Never operate the machine if the machine is not functioning properly.
12. Read all warnings posted on the exercise bike.
13. Inspect the exercise bike for worn or loose component prior to use. Tighten/replace any
loose or wore components prior to use.
14. Care should be taken in mounting or dismounting the exercise bike.
15. This exercise bike is for consumer and home use only.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.

© IMPEX INC. www.marcypro.com
3
WARNING LABEL PLACEMENT
The Warning Labels shown here has been placed on the Rear Stabilizer.
If the labels are missing or illegible, please call customer service at 1-800-999-8899 for
replacement. Apply the labels in location shown.

© IMPEX INC. www.marcypro.com
4
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
NO. Description Qty Drawings
6 Allen Bolt M8*2 ⅛4
7 Curved WasherΦ8xΦ¾ 8
8 Spring washer 4
11 Quick Release Knob 1
17 Allen Bolt M8x ⅝” 4
27 Locking Knob 1
28 Recovery Cover 1
Allen wrench 1
Allen key 6mm 1

© IMPEX INC. www.marcypro.com
5
COMPONENTS FOR ASSEMBLY
NO.1 NO.22
NO.18
NO.19
NO.15
NO.9/10
NO.16NO.3 NO.2
NO.5
NO.31

© IMPEX INC. www.marcypro.com
6
ASSEMBLY INSTRUCTION
•Tools Required for Assembling the Machine: One Crossing Wrench and Allen Wrench,
provided by manufacturer.
•NOTE: It is strongly recommended that two or more people assemble this machine to
avoid possible injury.
STEP-1
1. Thread the Stopper (#5) to the Front Stabilizer (#3).
2. Attach the Front Stabilizer (#3) to the main frame with two Allen bolts (#6), Curved washers (#7), Locking
Washers (#8).
7
8
3
5
5
6
6
7
8
5
5
3
2X 2X
2X
STEP-2
1. Thread the Stopper (#5) to the Rear Stabilizer (#2).
2. Attach the Rear Stabilizer (#2) to the main frame with two Allen bolts (#6), Curved washers (#7), Locking
Washers (#8).
8
6
7
8
55
5
5
2
2
6
7
2X 2X
2X

© IMPEX INC. www.marcypro.com
7
STEP-3
1. Connect Lower sensor wire (#23) to Upper sensor wire (#24).
2. Insert the Front Post (#22) into the main frame, secure with Allen bolts (#17) and Curved washers (#7).
7
17
7
17
7
17
23
24
4X 4X

© IMPEX INC. www.marcypro.com
8
STEP-4
1. Attach the Handlebar (#19) to the Clamp (#25) of the Front Post (#22).
2. Secure the Handlebar with Locking Knob(#28).
3. Insert the Hand pulse sensor wire (#38) into the hole on the Front Post (#22), and use the Grommet (#13) to close up
the hole.
4. Attach the Recovery cover (#27) to the Handle Bar (#19).
19
28
27
38
13
25
13
38
28
27
STEP-5
1. Connect the Upper sensor wire (#24) and Hand pulse sensor wire (#38) to the Computer (#18).
2. Attached the Computer to the Front Post with the 4 screws (#29) that are pre-assembled on the computer.
38 24
29
38 24
29

© IMPEX INC. www.marcypro.com
9
STEP-6
1. Secure the Seat Post Cover (#31) to the Seat Post (#15) with Self-tapping Screw (#36).
2. Insert the Seat Pad (#16) to the front of the Seat Post and secure the bolt from two sides.
3. Insert the Seat Post (#15) to the opening on the Main Frame (#1). Thread the Quick Release Knob (#11)
through the hole on Seat Post (#15) to securely lock it at desired height. When adjusting the seat, do not go
above the ‘’MAX Line’’ indicator on the seat support.
15
31
16
36
15
11
STEP-7
1. Secure the Bottle holder (#35) to the Front Post with Self-Tapping Screws (#36).
35 36