Impex Circuit Fitness AMZ-587R User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
AMZ-587R
Retain This
Manual for
Reference
190626
ASSEMBLY &
OWNER'S
MANUAL
Magnetic Resistance
Recumbent Bike
AMZ-587R
IMPEX®INC.
2801 S. Towne Ave, Pomona, CA 91766
Tel: [phone] Fax: [phone]
www.marcypro.com
[email protected]

1
© IMPEX INC. www.marcypro.com
TABLE OF CONTENTS
BEFORE YOU BEGIN
Thank you for selecting the CIRCUIT FITNESS Magnetic Resistance Recumbent Bike
AMZ-587R by IMPEX®INC. For your safety and benefit, read this manual carefully
before using the bike. As a manufacturer, we are committed to provide you complete
customer satisfaction. If you have anyquestions, or find there are missing or damaged
parts, we guarantee you complete satisfaction through direct assistance from our
factory. To avoid unnecessary delays, please call our TOLL-FREE customer service
number. Our Customer Service Agents will provide immediate assistance to you.
BEFORE YOU BEGIN
1
IMPORTANT SAFETY NOTICES
2
WARNING LABEL PLACEMENT
3
HARDWARE PACK
4
COMPONENT FOR ASSEMBLY
5
IMPORTANT ASSEMBLY INSTRUCTION
6
EXPLODED DIAGRAM
16
PARTS LIST
17
CARE AND MAINTENANCE, WEIGHT CAPACITY & DIMS.
18
COMPUTER
19
EXERCISE GUIDELINES
20
WARRANTY
26
ORDERING PARTS
26
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.marcypro.com
[email protected]

2
© IMPEX INC. www.marcypro.com
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave
children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near
water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or
other clothing that could become caught in the machine. Running or aerobic shoes
are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly
warm up.
11. Never operate the machine if the machine is not functioning properly.
12. Read all warnings posted on the exercise bike.
13. Inspect the exercise bike for worn or loose component prior to use. Tighten/replace
any loose or wore components prior to use.
14. Care should be taken in mounting or dismounting the exercise bike.
15. This exercise bike is for consumer and home use only.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.

3
© IMPEX INC. www.marcypro.com
WARNING LABEL PLACEMENT
The Warning Labels shown here has been placed on the Rear Stabilizer.
If the labels are missing or illegible, please call customer service at 1-800-999-8899 for
replacement. Apply the labels in location shown.

4
© IMPEX INC. www.marcypro.com
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
NO.
DESCRIPTION
Qty
Drawings
4
M10 x 2⅛” Carriage Bolt
4
5
Flat Washer
4
6
Hex Nut M10
4
21
Allen bolt M8 x 1”
2
22
Curved washer
4
23
M5 x 1”Round head bolt
2
24
Stopper
1
26
Allen Bolt M8 x ⅝”
16
27
M8 x 2”Carriage Bolt
2
28
Hex nut M8
2
Allen key L4
1
Allen key L6
1
Box Wrench
1

5
© IMPEX INC. www.marcypro.com
COMPONENTS FOR ASSEMBLY
NO.1 NO.7
NO.15 NO.14 NO.8 NO.2/3
NO.10/11 NO.13 NO.16 NO.30

6
© IMPEX INC. www.marcypro.com
ASSEMBLY INSTRUCTION
•Tools Required for Assembling the Machine: One Crossing Wrench and Allen
Wrench, provided by manufacturer.
•NOTE: It is strongly recommended that two or more people assemble this machine to
avoid possible injury.
STEP 1
1. Attach the Front Stabilizer (#3) with Carriage Bolts (#4), Flat Washers (#5) and Hex Nuts (#6)
to the Main Frame (#1).
2. Thread the Stopper (#24) into the Sliding Frame from the bottom.
24
4
55
6
6
3
2X 2X
2X

7
© IMPEX INC. www.marcypro.com
STEP 2
Attach the Rear Stabilizer (#2) with Carriage Bolts (#4), Flat Washers (#5) and Hex Nuts (#6) to
the Main Frame.
2X 2X
2X
1
4
5
5
6
6
2

8
© IMPEX INC. www.marcypro.com
STEP 3
1. Connect Middle computer wire (#17) to the Lower computer wire (#18).
2. Connect Front extension hand pulse wire (#19) with Middle extension hand pulse wire (#20).
3. Attach the Front Post (#7)to the Main Frame, secure with Allen Bolts (#21) and Curved
washers (#22).
4X 4X
19
17
20
18
21
22
1
7

9
© IMPEX INC. www.marcypro.com
STEP 4
1. Connect the hand pulse wire (#19) to the computer, and computer wire (#17) to the computer.
2. Secure the computer (#8) to the Front post with Screws (pre-assembled on the Computer)
(#9) .
8
19
17
9
9
9
1

10
© IMPEX INC. www.marcypro.com
STEP 5
Secure the Quick Release handle (#16) with Round Bolts (#23) to the Rear Sliding Frame.
16
23 1
2X

11
© IMPEX INC. www.marcypro.com
STEP 6
Secure the Seat Pad (#13) to the Main Frame with Allen Bolts (#26).
13
26
26
1
4X

12
© IMPEX INC. www.marcypro.com
STEP 7
Insert the Backrest Support(#15) to the Rear Sliding Frame, secure with Allen Bolt (#26).
15
26
26
6X
1
26

13
© IMPEX INC. www.marcypro.com
STEP 8
Attach the Backrest board (#14) to the Back Support with Allen Bolts (#26).
STEP 9
1. Secure the Handlebar (#12) to the back of the Seat with Curved washers (#22) and Hex Nuts
(#28).
2. Connect Hand pulse wire (#20) to the Hand pulse wire (#29) on the Handlebar (#29).
14
26
26
4X
29
20
28
28 22
22
12
27
2X 2X 2X
1

14
© IMPEX INC. www.marcypro.com
STEP 10
Thread the Left Pedal (#11) to the Left Crank(#25L)
STEP 11
Thread the Right Pedal (#10) to the Right Crank (#25R)
11
25L
L
10
25R
R

15
© IMPEX INC. www.marcypro.com
STEP 12
Insert the Adapter to the inlet in the Chain Cover, and the Auxiliary Line to the computer.
31

16
© IMPEX INC. www.marcypro.com
EXPLODED DIAGRAM
1
2
3
4
4
5
6
6
5
7
8
9
19
17 20
18
21
22
22
23
20
26
26
26
26
26
26
26
26
27
28
29
25R 10
11
12
13
14
15
16
26
30
31
24

17
© IMPEX INC. www.marcypro.com
AMZ-587R PARTS LIST
ITEM NO.
DESCRIPTION
QTY
1
Main Frame
1
2
Rear Stabilizer
1
3
Front Stabilizer
1
4
Carriage Bolt M10 x 2⅛”
4
5
Flat Washer
4
6
Hex Nut M10
4
7
Front Post
1
8
Computer
4
9
Screw for computer
4
10
Pedal (Right)
1
11
Pedal (Left)
1
12
Handlebar
1
13
Seat Pad
1
14
Backrest Board
1
15
Backrest Support
1
16
Quick release handle
1
17
Middle computer wire
1
18
Lower computer wire
1
19
Front extension hand pulse wire
1
20
Middle extension hand pulse wire
1
21
Allen bolt M8 x 1”
2
22
Curved washer
4
23
Round Bolt M5 x 1”
2
24
Stopper
1
25
Crank
2
26
Allen Bolt M8 x ⅝”
16
27
Carriage Bolt M8 x 2”
2
28
Hex Nut M8
2
29
Hand Pulse Wire
1
30
Adapter
1/1
31
Auxiliary Line
1

18
© IMPEX INC. www.marcypro.com
CARE, MAINTENANCE AND STORAGE
1. Inspect and tighten all parts each time you use the machine. Replace any worn parts
immediately.
2. This machine can be cleaned using a damp cloth and mild non-abrasive detergent. Do not
use solvents.
3. Store the rower IN-DOOR. Excess moisture and water would cause rust on the frame.
4. The rower shall be placed at least 24 inches away from the wall or/and any other object such
as furniture to provide safe access to and passage around the machine.
5. To avoid possible injury, the help of two or more people are needed when moving the
machine around.
6. Disposal Instructions –The equipment can be safely disassembled and disposed without
unreasonable hazards. Call your local recycle agency regarding details of recycling.
7. The maximum user weight is 300 lbs.
8. Assembled Dimension (L x W x H): 55” x 24.8” x 48.5”
OPERATING NOTES
1.Adjustment of the Seat position. Pull up on the Quick Release Handle to adjust
forward/backward. Push down to lock the seat into position.
2.Thread the Stopper (#24) to ensure the bike is level.
16
13
24

19
© IMPEX INC. www.marcypro.com
COMPUTER
DISPLAY FUNCTIONS
ITEM
DESCRIPTION
TIME
Count up –With no preset target (time), Time will count up from 00:00 to maximum 99:59 with each
increment being 1 second.
Count down - If training with preset Time, Time will count down from preset to 00:00.
Each preset increment or decrement is 1 second between 00:00 to 99:00.
SPEED
Displays current training speed. Maximum speed is 99.9 KM/H or ML/H.
RPM
Displays the Rotation Per Minute. Display range 0~15~999
DISTANCE
Accumulates total distance from 0.00 up to 99.99 Miles. The user may preset target distance by using
UP/DOWN button.
Each preset increment or decrement is 0.1 mile between 0.00 to 99.90.
CALORIES
Accumulates calories consumption during training from 0 to maximum 9999 calories.
(This data is a only for reference for comparison of different exercise sessions and SHOULD NOT be
used in medical treatment.)
PULSE
User may set up target pulse from 0 - 30 to 230; and computer buzzer will beep when actual heart rate
is over the target value during workout.
WATTS
Display current workout watts. Display range 0~999.
MANUAL
Manual mode workout.
BEGINNER
4 PROGRAM selection.
ADVANCE
4 PROGRAM selection.
SPORTY
4 PROGRAM selection.
CARDIO
Target HR training mode.
WATT PROGRAM
WATT constant training mode.
USB Port
Power only, does not provide data transfer. Use to charge your mobile devices.