impey Mantis Shower Tray User manual

Mantis Shower Tray
Installation Guide
SAFETY
Please read these installation instructions carefully before proceeding. •
Keep guide for future reference. •
If you are unsure about any part of the installation, please contact our technical department on 01460 258 682 •
Incorrect installation will invalidate the guarantee. •
Make sure there are no hidden pipes or cables in the floor or walls where you intend to drill. •
Ensure you have all of the appropriate PPE. •
Important note: This shower tray must be used with showers that have flow rates of 12 l/min or less.
CARE
Please protect the surface of the shower tray during installation. •
Please do not walk on the tray with shoes on. •
Only use mild household detergents to clean the product. •
Do not use polish or abrasive cleaners on the surface of the tray. •
Ensure the shower tray is thoroughly cleaned after installation and before first use. •
Issue 1
14/03/16

Drain Cover Cap
90mm Threaded Waste
Dip Tube
Trap Basket
50mm Ball Joint Outlet
Trap Body
Rubber Seal
Mantis Shower Tray
Installation Guide
Component Content List
US 12350
waterproof
self adhesive
tiling upstand
(3.5m roll - 120mm)
Mantis Shower Tray
Page 1
90mm Waste Trap
(supplied as standard)
(other waste options available)

This guide is non specific to timber or concrete floors, it may refer to timber floors but in general the process of installation is the same
regardless of floor type. In both cases great care must be taken when either lifting floor board or excavating the floor for waste installation.
Concrete floors, excavate suficient
concrete to install trap and waste pipe.
Measure and cut the required length of fabric tile
up-stand. The length will be the determned by measuirng
the sides of the tray the are against a wall.
Place the tray in the desired location and mark position
of shower trap.
Using a suitable saw, remove enough floor boards to
receive the shower trap and any drainage pipework.
Use extreme care whilst cutting the floor as there
may be hidden pipes and cables.
Position the trap so that it aligns with the hole in the
shower tray and connect it to the waste pipe. Remove
internal parts of the trap and place to one side, as
they will be required later.
Mantis Shower Tray
Installation Guide
Do not stretch as you apply.
3. 4.
5.
2.
6.
1.
Determine which corner the tray is to be fitted into.
This will establish which edges the fabric up stand
will be attached to.
First remove the backing paper. Carefully position against
the tray and press firmly into place ensuring there are no
bubbles or creases.
We recommend using a roller to do this.
Page 2

Concrete floors, ensure excavated hole is made good.
Put the tray in position and press the upstand into tile
adhesive ensuring there are no air gaps.
Ensure the tray is level on all four sides.
Allow 24 hours before exposing to water.
The trap can now be reassembled and connected to
the tray.
Tiling can now be completed in an approved manner.
Mantis Shower Tray
Installation Guide
9. 10.
8.7.
Apply tile adhesive to the wall ready for the tile upstand.
It may be desirable to bed the shower tray down on sand
and cement or tile adhesive. This can assist with levelling
the shower tray and offer additional support.
Page 3
If you require any further information about
this product please contact our techincal
department on: 01460 258 682
Impey Showers
Conquest Business Park
Ilton
Somerset
TA19 9EA
TEL: [phone]
FAX: [phone]
[email protected]
www.impeyshowers.com
This guide is non specific to timber or concrete floors, it may refer to timber floors but in general the process of installation is the same
regardless of floor type. In both cases great care must be taken when either lifting floor board or excavating the floor for waste installation.