Inateck P6 User manual

UseofInateckP6
Startup
Note:
1)InateckP6willstartsleepmodeifthereisnooperationonitover
3minutes.Shortpressonthetriggercanwakeitup.
2)WhenthedistancebetweenInateckP6anditsadapterexceeds
the effective range, scanned data will be kept in the buffer of
InateckP6.Quicklydoublepressonthetriggercanuploaddata
frombuffer.
WirelessMode:
1.Insertthe2.4GUSBadapterintotheUSBportofcomputer.The
initializationiscompletedifblueLEDontheadapterblinksonce.
2.PoweronInateckP6bytogglingswitchfromOFFtoON.Short
pressthetriggertoemitredlaserbeamandscanbarcodes.
3.Open afileon computerandmovecursor to the blankwhere
scanning output should be placed. Scanning results can be
displayedoncomputerthen.
WiredMode:
1.ConnectInateckP6withcomputerviaUSBcable
2.PoweronInateckP6bytogglingswitchfromOFFtoONandshort
pressthetrigger.InateckP6willcontinuouslybeep.Beepstops
aftersuccessfulconnection.
3.Open afileon computer and movecursorto the blankwhere
scanning output should be placed. Scanning results can be
displayedoncomputerthen.
FunctionSetup
(Note:Thebarcodemarkedby“*”meansdefaultsettingofInateckP6.)
Users must read setup barcodes in order to change the default
settingsinInateckP6BarcodeScanner.
Statusindication
BuzzerIndication
LEDIndication
FrequentlyUsedBarcodes
SettingforKeyboardLanguage
1.ReadʼEntersetupʼBarcode
2.SelectandScanyourkeyboardlanguageBarcode
3.Scan“ExitwithSave”Barcodetoendlanguagesetting
Note: The keyboard language of Inateck P6 should keep
consistent with that on computer, otherwise, garbled might
appearinscanningresult.
SettingforPrefix/Suffix
Userscanaddprefix/suffixtoscanningresult.Theprefix/suffixcan
have1to8digits.Moredetailsareasbelow.
1.Scan“Entersetupʼ”Barcode
2.Scan“PrefixSetting”or“SuffixSetting”
3. Scan the character barcode (8 characters at the most). For
instance, “H#” is the prefix/suffix to be added to the scanning
result,scanthecharacterbarcodeof“H”and“#”below.
4.Scan“ExitwithSave”Barcodetoendthesetting
UserGuide
P6BarcodeScanner
123
4567
8 9 10 11
12 13 14 15
16 17 18 19
20 21 22 23
24 25 26 27
28 29 30 31

ShockproofCover
LaserWindow
PowerSwitch
LED1
LED2
Trigger
Buzzer
USBPort
ProductOverview
UseofInateckP6
Startup
Note:
1)InateckP6willstartsleepmodeifthereisnooperationonitover
3minutes.Shortpressonthetriggercanwakeitup.
2)WhenthedistancebetweenInateckP6anditsadapterexceeds
the effective range, scanned data will be kept in the buffer of
InateckP6.Quicklydoublepressonthetriggercanuploaddata
frombuffer.
WirelessMode:
1.Insertthe2.4GUSBadapterintotheUSBportofcomputer.The
initializationiscompletedifblueLEDontheadapterblinksonce.
2.PoweronInateckP6bytogglingswitchfromOFFtoON.Short
pressthetriggertoemitredlaserbeamandscanbarcodes.
3.Open afileon computerandmovecursor to the blankwhere
scanning output should be placed. Scanning results can be
displayedoncomputerthen.
WiredMode:
English
1.ConnectInateckP6withcomputerviaUSBcable
2.PoweronInateckP6bytogglingswitchfromOFFtoONandshort
pressthetrigger.InateckP6willcontinuouslybeep.Beepstops
aftersuccessfulconnection.
3.Open afileon computerandmovecursor to the blankwhere
scanning output should be placed. Scanning results can be
displayedoncomputerthen.
FunctionSetup
(Note:Thebarcodemarkedby“*”meansdefaultsettingofInateckP6.)
Users must read setup barcodes in order to change the default
settingsinInateckP6BarcodeScanner.
Statusindication
BuzzerIndication
LEDIndication
FrequentlyUsedBarcodes
SettingforKeyboardLanguage
1.ReadʼEntersetupʼBarcode
2.SelectandScanyourkeyboardlanguageBarcode
3.Scan“ExitwithSave”Barcodetoendlanguagesetting
Note: The keyboard language of Inateck P6 should keep
consistent with that on computer, otherwise, garbled might
appearinscanningresult.
SettingforPrefix/Suffix
Userscanaddprefix/suffixtoscanningresult.Theprefix/suffixcan
have1to8digits.Moredetailsareasbelow.
1.Scan“Entersetupʼ”Barcode
2.Scan“PrefixSetting”or“SuffixSetting”
3. Scan the character barcode (8 characters at the most). For
instance, “H#” is the prefix/suffix to be added to the scanning
result,scanthecharacterbarcodeof“H”and“#”below.
4.Scan“ExitwithSave”Barcodetoendthesetting
1 2 3
4567
8 9 10 11
12 13 14 15
16 17 18 19
20 21 22 23
24 25 26 27
28 29 30 31

UseofInateckP6
Startup
Note:
1)InateckP6willstartsleepmodeifthereisnooperationonitover
3minutes.Shortpressonthetriggercanwakeitup.
2)WhenthedistancebetweenInateckP6anditsadapterexceeds
the effective range, scanned data will be kept in the buffer of
InateckP6.Quicklydoublepressonthetriggercanuploaddata
frombuffer.
WirelessMode:
1.Insertthe2.4GUSBadapterintotheUSBportofcomputer.The
initializationiscompletedifblueLEDontheadapterblinksonce.
2.PoweronInateckP6bytogglingswitchfromOFFtoON.Short
pressthetriggertoemitredlaserbeamandscanbarcodes.
3.Open afileon computerandmovecursor to the blankwhere
scanning output should be placed. Scanning results can be
displayedoncomputerthen.
WiredMode:
1.ConnectInateckP6withcomputerviaUSBcable
2.PoweronInateckP6bytogglingswitchfromOFFtoONandshort
pressthetrigger.InateckP6willcontinuouslybeep.Beepstops
aftersuccessfulconnection.
3.Open afileon computerandmovecursor to the blankwhere
scanning output should be placed. Scanning results can be
displayedoncomputerthen.
FunctionSetup
(Note:Thebarcodemarkedby“*”meansdefaultsettingofInateckP6.)
Users must read setup barcodes in order to change the default
settingsinInateckP6BarcodeScanner.
Statusindication
BuzzerIndication
LEDIndication
FrequentlyUsedBarcodes
SettingforKeyboardLanguage
1.ReadʼEntersetupʼBarcode
2.SelectandScanyourkeyboardlanguageBarcode
3.Scan“ExitwithSave”Barcodetoendlanguagesetting
Note: The keyboard language of Inateck P6 should keep
consistent with that on computer, otherwise, garbled might
appearinscanningresult.
SettingforPrefix/Suffix
Userscanaddprefix/suffixtoscanningresult.Theprefix/suffixcan
have1to8digits.Moredetailsareasbelow.
1.Scan“Entersetupʼ”Barcode
2.Scan“PrefixSetting”or“SuffixSetting”
3. Scan the character barcode (8 characters at the most). For
instance, “H#” is the prefix/suffix to be added to the scanning
result,scanthecharacterbarcodeof“H”and“#”below.
4.Scan“ExitwithSave”Barcodetoendthesetting
123
4567
8 9 10 11
12 13 14 15
16 17 18 19
20 21 22 23
24 25 26 27
28 29 30 31

UseofInateckP6
Startup
Note:
1)InateckP6willstartsleepmodeifthereisnooperationonitover
3minutes.Shortpressonthetriggercanwakeitup.
2)WhenthedistancebetweenInateckP6anditsadapterexceeds
the effective range, scanned data will be kept in the buffer of
InateckP6.Quicklydoublepressonthetriggercanuploaddata
frombuffer.
WirelessMode:
1.Insertthe2.4GUSBadapterintotheUSBportofcomputer.The
initializationiscompletedifblueLEDontheadapterblinksonce.
2.PoweronInateckP6bytogglingswitchfromOFFtoON.Short
pressthetriggertoemitredlaserbeamandscanbarcodes.
3.Open afileon computerandmovecursor to the blankwhere
scanning output should be placed. Scanning results can be
displayedoncomputerthen.
WiredMode:
Scan“Enter setup”barcode;
Change scanner setting by
scanning certain function
setup barcode;
Scan “Exit with save” barcode
to finish the setup.
1.ConnectInateckP6withcomputerviaUSBcable
2.PoweronInateckP6bytogglingswitchfromOFFtoONandshort
pressthetrigger.InateckP6willcontinuouslybeep.Beepstops
aftersuccessfulconnection.
3.Open afileon computerandmovecursor to the blankwhere
scanning output should be placed. Scanning results can be
displayedoncomputerthen.
FunctionSetup
(Note:Thebarcodemarkedby“*”meansdefaultsettingofInateckP6.)
Users must read setup barcodes in order to change the default
settingsinInateckP6BarcodeScanner.
Statusindication
BuzzerIndication
LEDIndication
FrequentlyUsedBarcodes
SettingforKeyboardLanguage
1.ReadʼEntersetupʼBarcode
2.SelectandScanyourkeyboardlanguageBarcode
3.Scan“ExitwithSave”Barcodetoendlanguagesetting
Note: The keyboard language of Inateck P6 should keep
consistent with that on computer, otherwise, garbled might
appearinscanningresult.
SettingforPrefix/Suffix
Userscanaddprefix/suffixtoscanningresult.Theprefix/suffixcan
have1to8digits.Moredetailsareasbelow.
1.Scan“Entersetupʼ”Barcode
2.Scan“PrefixSetting”or“SuffixSetting”
3. Scan the character barcode (8 characters at the most). For
instance, “H#” is the prefix/suffix to be added to the scanning
result,scanthecharacterbarcodeof“H”and“#”below.
4.Scan“ExitwithSave”Barcodetoendthesetting
Beeping Meaning
Readbarcodesuccessfully
DatauploadfromscannertoComputer
WrongSetup
（onsetupstatus,blueLEDstayson）
Invalidscanningduetofullbuffer
(Scannedbarcodenotsaved.)
USBbeingconfigured（Ithappenswhen
USBcableisinserted）
Entersetupmode（BlueLEDon）
Exitsetupmode（BlueLEDoff）
CorrectSetup
TheconnectionbetweenInateckP6and
computerisdisrupted.
Oneshorthighnote（100ms）
Oneshorthighnote（20ms）
Onelonghighnote（400ms）
Oneorseverallonghighnotes
（800ms）
Threechordsounds
Twoshortnotes（tonefromlow
tohigh）
Twoshortbeeps(tonefrom
hightolow)
FrequentlyUsedPrefix/SuffixBarcodes
Note:
1) More prefix/suffix barcodes are available at www.inateck.com.
Userscandownloadthemfromthesite.Foranyotherquestions,
pleasesendemailto[e-mail].
2) Scanning result will come with prefix/suffix after the setting.
Nevertheless,prefix/suffixcanbehiddenorrecovered.Tohide
prefix/suffix, scan “Enter Setup” barcode, “Hide Prefix/Suffix”
barcode,andthen“ExitwithSave”barcode.Torecoverprefix/suffix,
scan“EnterSetup”barcode,“RecoverPrefix/Suffix”barcode,and
then“ExitwithSave”barcode.
DeleteCharacter(s)onOutputResult
InateckP6canhelpusersdeletecharacter(s)onoutputresult,either
beginning characters or the ending ones. 0 to 9 digits can be
deleted.Asdefaultsetting,nocharacter,orsay0digitisdeletedas
outputresult.Moredetailsareasbelow.
1.Scan“EnterSetup”Barcode
2.Scan“DeleteBeginningCharacter(s)”Barcodeor“DeleteEnding
Character(s)”Barcode
3.Scanthedigit(s)barcodetobedeleted.
4.Scan“ExitwithSave”Barcodetoendthesetting
Note:Refertothesettingof“delete0digitcharacter”ifnocharacter
shouldbedeleted.
InventoryMode
Users mayuseinventorymodeto keepscannedbarcodes in the
buffer of Inateck P6, and upload them to computer in batches.
Under inventory mode users are not restricted to the time and
locationwhenuploaddata.Ofcourse,historydatacanbeclearedin
buffer.Moredetailsaboutinventorymodeareasbelow.
1.ScanthebarcodetoenterInventoryMode
2.ScanthebarcodetoreturntoCommonMode
3.Scanthebarcodetocleardatainbuffer(forInventoryModeonly).
4.Scanthebarcodetouploaddatafrombuffer(forInventoryMode
only)
5.Scanthebarcodetouploadthenumberofscannedbarcodes(for
InventoryModeonly)
Note:
1) To use inventory mode, users just need scan “Enter Inventory
Mode”barcode;anddonothavetoscan“EnterSetup”barcode
beforethat.
2)Toendinventorymode,usersjustneedscan“ReturntoCommon
Mode”barcode.
FunctionSetupBarcodes
1 2 3
4567
8 9 10 11
12 13 14 15
16 17 18 19
20 21 22 23
24 25 26 27
28 29 30 31

UseofInateckP6
Startup
Note:
1)InateckP6willstartsleepmodeifthereisnooperationonitover
3minutes.Shortpressonthetriggercanwakeitup.
2)WhenthedistancebetweenInateckP6anditsadapterexceeds
the effective range, scanned data will be kept in the buffer of
InateckP6.Quicklydoublepressonthetriggercanuploaddata
frombuffer.
WirelessMode:
1.Insertthe2.4GUSBadapterintotheUSBportofcomputer.The
initializationiscompletedifblueLEDontheadapterblinksonce.
2.PoweronInateckP6bytogglingswitchfromOFFtoON.Short
pressthetriggertoemitredlaserbeamandscanbarcodes.
3.Open afileon computerandmovecursor to the blankwhere
scanning output should be placed. Scanning results can be
displayedoncomputerthen.
WiredMode:
1.ConnectInateckP6withcomputerviaUSBcable
2.PoweronInateckP6bytogglingswitchfromOFFtoONandshort
pressthetrigger.InateckP6willcontinuouslybeep.Beepstops
aftersuccessfulconnection.
3.Open afileon computer and movecursorto the blankwhere
scanning output should be placed. Scanning results can be
displayedoncomputerthen.
FunctionSetup
(Note:Thebarcodemarkedby“*”meansdefaultsettingofInateckP6.)
Users must read setup barcodes in order to change the default
settingsinInateckP6BarcodeScanner.
Statusindication
BuzzerIndication
LEDIndication
FrequentlyUsedBarcodes
EnterSetup ExitwithSave
ExitwithoutSave RestoreFactorySetting
（*）ApplyEnterforSuffix
（*）EnableAutoLaser-darkeningMode
EnableContinuousScanningMode
DoNotApplyEnterforSuffix
EnableManualScanningMode
EnableAutoInductionMode
SettingforKeyboardLanguage
1.ReadʼEntersetupʼBarcode
2.SelectandScanyourkeyboardlanguageBarcode
3.Scan“ExitwithSave”Barcodetoendlanguagesetting
Note: The keyboard language of Inateck P6 should keep
consistent with that on computer, otherwise, garbled might
appearinscanningresult.
SettingforPrefix/Suffix
Userscanaddprefix/suffixtoscanningresult.Theprefix/suffixcan
have1to8digits.Moredetailsareasbelow.
1.Scan“Entersetupʼ”Barcode
2.Scan“PrefixSetting”or“SuffixSetting”
3. Scan the character barcode (8 characters at the most). For
instance, “H#” is the prefix/suffix to be added to the scanning
result,scanthecharacterbarcodeof“H”and“#”below.
4.Scan“ExitwithSave”Barcodetoendthesetting
LEDStatus Meaning
Barcodesuccessfullyreadand
uploadedtocomputer
Barcodesuccessfullyreadandsavedin
buffer,butnotuploadedtocomputer
InateckP6scanneronsetupstatus
Lowbattery
InateckP6scannerincharge(RedLED
offwhenbatteryisfull)
GreenLEDflashesonce(LED2)
BlueLEDflashesonce(LED2)
BlueLEDstayson(LED2)
YellowLEDblinks（light/shade
ratio0.5s:0.5s）(LED1)
RedLEDstayson(LED1)
123
4 5 6 7
8 9 10 11
12 13 14 15
16 17 18 19
20 21 22 23
24 25 26 27
28 29 30 31

UseofInateckP6
Startup
Note:
1)InateckP6willstartsleepmodeifthereisnooperationonitover
3minutes.Shortpressonthetriggercanwakeitup.
2)WhenthedistancebetweenInateckP6anditsadapterexceeds
the effective range, scanned data will be kept in the buffer of
InateckP6.Quicklydoublepressonthetriggercanuploaddata
frombuffer.
WirelessMode:
1.Insertthe2.4GUSBadapterintotheUSBportofcomputer.The
initializationiscompletedifblueLEDontheadapterblinksonce.
2.PoweronInateckP6bytogglingswitchfromOFFtoON.Short
pressthetriggertoemitredlaserbeamandscanbarcodes.
3.Open afileon computerandmovecursor to the blankwhere
scanning output should be placed. Scanning results can be
displayedoncomputerthen.
WiredMode:
1.ConnectInateckP6withcomputerviaUSBcable
2.PoweronInateckP6bytogglingswitchfromOFFtoONandshort
pressthetrigger.InateckP6willcontinuouslybeep.Beepstops
aftersuccessfulconnection.
3.Open afileon computer and movecursorto the blankwhere
scanning output should be placed. Scanning results can be
displayedoncomputerthen.
FunctionSetup
(Note:Thebarcodemarkedby“*”meansdefaultsettingofInateckP6.)
Users must read setup barcodes in order to change the default
settingsinInateckP6BarcodeScanner.
Statusindication
BuzzerIndication
LEDIndication
FrequentlyUsedBarcodes
（*）EnableAuto-sleepMode
2.4GParing
（*）USKeyboard GermanKeyboard
FrenchKeyboard
ItalianKeyboard
SpanishKeyboard
DisableAuto-sleepMode
Lowercaseforallletters
Uppercaseforallletters （*）Keeporiginalcase
SettingforKeyboardLanguage
1.ReadʼEntersetupʼBarcode
2.SelectandScanyourkeyboardlanguageBarcode
3.Scan“ExitwithSave”Barcodetoendlanguagesetting
Note: The keyboard language of Inateck P6 should keep
consistent with that on computer, otherwise, garbled might
appearinscanningresult.
SettingforPrefix/Suffix
Userscanaddprefix/suffixtoscanningresult.Theprefix/suffixcan
have1to8digits.Moredetailsareasbelow.
1.Scan“Entersetupʼ”Barcode
2.Scan“PrefixSetting”or“SuffixSetting”
3. Scan the character barcode (8 characters at the most). For
instance, “H#” is the prefix/suffix to be added to the scanning
result,scanthecharacterbarcodeof“H”and“#”below.
4.Scan“ExitwithSave”Barcodetoendthesetting
EnterSetup
123
45 6 7
8 9 10 11
12 13 14 15
16 17 18 19
20 21 22 23
24 25 26 27
28 29 30 31

UseofInateckP6
Startup
Note:
1)InateckP6willstartsleepmodeifthereisnooperationonitover
3minutes.Shortpressonthetriggercanwakeitup.
2)WhenthedistancebetweenInateckP6anditsadapterexceeds
the effective range, scanned data will be kept in the buffer of
InateckP6.Quicklydoublepressonthetriggercanuploaddata
frombuffer.
WirelessMode:
1.Insertthe2.4GUSBadapterintotheUSBportofcomputer.The
initializationiscompletedifblueLEDontheadapterblinksonce.
2.PoweronInateckP6bytogglingswitchfromOFFtoON.Short
pressthetriggertoemitredlaserbeamandscanbarcodes.
3.Open afileon computerandmovecursor to the blankwhere
scanning output should be placed. Scanning results can be
displayedoncomputerthen.
WiredMode:
1.ConnectInateckP6withcomputerviaUSBcable
2.PoweronInateckP6bytogglingswitchfromOFFtoONandshort
pressthetrigger.InateckP6willcontinuouslybeep.Beepstops
aftersuccessfulconnection.
3.Open afileon computer and movecursorto the blankwhere
scanning output should be placed. Scanning results can be
displayedoncomputerthen.
FunctionSetup
(Note:Thebarcodemarkedby“*”meansdefaultsettingofInateckP6.)
Users must read setup barcodes in order to change the default
settingsinInateckP6BarcodeScanner.
Statusindication
BuzzerIndication
LEDIndication
FrequentlyUsedBarcodes
SettingforKeyboardLanguage
1.ReadʼEntersetupʼBarcode
2.SelectandScanyourkeyboardlanguageBarcode
3.Scan“ExitwithSave”Barcodetoendlanguagesetting
Note: The keyboard language of Inateck P6 should keep
consistent with that on computer, otherwise, garbled might
appearinscanningresult.
SettingforPrefix/Suffix
Userscanaddprefix/suffixtoscanningresult.Theprefix/suffixcan
have1to8digits.Moredetailsareasbelow.
1.Scan“Entersetupʼ”Barcode
2.Scan“PrefixSetting”or“SuffixSetting”
3. Scan the character barcode (8 characters at the most). For
instance, “H#” is the prefix/suffix to be added to the scanning
result,scanthecharacterbarcodeof“H”and“#”below.
4.Scan“ExitwithSave”Barcodetoendthesetting
EnterSetup
PrefixSetting SuffixSetting
#H
ExitwithSave
ExitwithSave
123
4 5 6 7
8 9 10 11
12 13 14 15
16 17 18 19
20 21 22 23
24 25 26 27
28 29 30 31

UseofInateckP6
Startup
Note:
1)InateckP6willstartsleepmodeifthereisnooperationonitover
3minutes.Shortpressonthetriggercanwakeitup.
2)WhenthedistancebetweenInateckP6anditsadapterexceeds
the effective range, scanned data will be kept in the buffer of
InateckP6.Quicklydoublepressonthetriggercanuploaddata
frombuffer.
WirelessMode:
1.Insertthe2.4GUSBadapterintotheUSBportofcomputer.The
initializationiscompletedifblueLEDontheadapterblinksonce.
2.PoweronInateckP6bytogglingswitchfromOFFtoON.Short
pressthetriggertoemitredlaserbeamandscanbarcodes.
3.Open afileon computerandmovecursor to the blankwhere
scanning output should be placed. Scanning results can be
displayedoncomputerthen.
WiredMode:
1.ConnectInateckP6withcomputerviaUSBcable
2.PoweronInateckP6bytogglingswitchfromOFFtoONandshort
pressthetrigger.InateckP6willcontinuouslybeep.Beepstops
aftersuccessfulconnection.
3.Open afileon computer and movecursorto the blankwhere
scanning output should be placed. Scanning results can be
displayedoncomputerthen.
FunctionSetup
(Note:Thebarcodemarkedby“*”meansdefaultsettingofInateckP6.)
Users must read setup barcodes in order to change the default
settingsinInateckP6BarcodeScanner.
Statusindication
BuzzerIndication
LEDIndication
FrequentlyUsedBarcodes
SettingforKeyboardLanguage
1.ReadʼEntersetupʼBarcode
2.SelectandScanyourkeyboardlanguageBarcode
3.Scan“ExitwithSave”Barcodetoendlanguagesetting
Note: The keyboard language of Inateck P6 should keep
consistent with that on computer, otherwise, garbled might
appearinscanningresult.
SettingforPrefix/Suffix
Userscanaddprefix/suffixtoscanningresult.Theprefix/suffixcan
have1to8digits.Moredetailsareasbelow.
1.Scan“Entersetupʼ”Barcode
2.Scan“PrefixSetting”or“SuffixSetting”
3. Scan the character barcode (8 characters at the most). For
instance, “H#” is the prefix/suffix to be added to the scanning
result,scanthecharacterbarcodeof“H”and“#”below.
4.Scan“ExitwithSave”Barcodetoendthesetting
Tab Backspace
Enter Space
（*）RecoverPrefix HidePrefix
（*）RecoverSuffix HideSuffix
FrequentlyUsedPrefix/SuffixBarcodes
Note:
1) More prefix/suffix barcodes are available at www.inateck.com.
Userscandownloadthemfromthesite.Foranyotherquestions,
pleasesendemailto[e-mail].
2) Scanning result will come with prefix/suffix after the setting.
Nevertheless,prefix/suffixcanbehiddenorrecovered.Tohide
prefix/suffix, scan “Enter Setup” barcode, “Hide Prefix/Suffix”
barcode,andthen“ExitwithSave”barcode.Torecoverprefix/suffix,
scan“EnterSetup”barcode,“RecoverPrefix/Suffix”barcode,and
then“ExitwithSave”barcode.
DeleteCharacter(s)onOutputResult
InateckP6canhelpusersdeletecharacter(s)onoutputresult,either
beginning characters or the ending ones. 0 to 9 digits can be
deleted.Asdefaultsetting,nocharacter,orsay0digitisdeletedas
outputresult.Moredetailsareasbelow.
1.Scan“EnterSetup”Barcode
2.Scan“DeleteBeginningCharacter(s)”Barcodeor“DeleteEnding
Character(s)”Barcode
3.Scanthedigit(s)barcodetobedeleted.
4.Scan“ExitwithSave”Barcodetoendthesetting
Note:Refertothesettingof“delete0digitcharacter”ifnocharacter
shouldbedeleted.
InventoryMode
Users mayuseinventorymodeto keepscannedbarcodes in the
buffer of Inateck P6, and upload them to computer in batches.
Under inventory mode users are not restricted to the time and
locationwhenuploaddata.Ofcourse,historydatacanbeclearedin
buffer.Moredetailsaboutinventorymodeareasbelow.
1.ScanthebarcodetoenterInventoryMode
2.ScanthebarcodetoreturntoCommonMode
3.Scanthebarcodetocleardatainbuffer(forInventoryModeonly).
4.Scanthebarcodetouploaddatafrombuffer(forInventoryMode
only)
5.Scanthebarcodetouploadthenumberofscannedbarcodes(for
InventoryModeonly)
Note:
1) To use inventory mode, users just need scan “Enter Inventory
Mode”barcode;anddonothavetoscan“EnterSetup”barcode
beforethat.
2)Toendinventorymode,usersjustneedscan“ReturntoCommon
Mode”barcode.
FunctionSetupBarcodes
123
4567
8 9 10 11
12 13 14 15
16 17 18 19
20 21 22 23
24 25 26 27
28 29 30 31

DeleteBeginningCharacter(s) DeleteEndingCharacter(s)
（*）0digit 1digit
2digit 3digits
4digit 5digits
6digit 7digits
8digit 9digits
EnterSetup
FrequentlyUsedPrefix/SuffixBarcodes
Note:
1) More prefix/suffix barcodes are available at www.inateck.com.
Userscandownloadthemfromthesite.Foranyotherquestions,
pleasesendemailto[e-mail].
2) Scanning result will come with prefix/suffix after the setting.
Nevertheless,prefix/suffixcanbehiddenorrecovered.Tohide
prefix/suffix, scan “Enter Setup” barcode, “Hide Prefix/Suffix”
barcode,andthen“ExitwithSave”barcode.Torecoverprefix/suffix,
scan“EnterSetup”barcode,“RecoverPrefix/Suffix”barcode,and
then“ExitwithSave”barcode.
DeleteCharacter(s)onOutputResult
InateckP6canhelpusersdeletecharacter(s)onoutputresult,either
beginning characters or the ending ones. 0 to 9 digits can be
deleted.Asdefaultsetting,nocharacter,orsay0digitisdeletedas
outputresult.Moredetailsareasbelow.
1.Scan“EnterSetup”Barcode
2.Scan“DeleteBeginningCharacter(s)”Barcodeor“DeleteEnding
Character(s)”Barcode
3.Scanthedigit(s)barcodetobedeleted.
4.Scan“ExitwithSave”Barcodetoendthesetting
Note:Refertothesettingof“delete0digitcharacter”ifnocharacter
shouldbedeleted.
InventoryMode
Users mayuseinventorymodeto keepscannedbarcodes in the
buffer of Inateck P6, and upload them to computer in batches.
Under inventory mode users are not restricted to the time and
locationwhenuploaddata.Ofcourse,historydatacanbeclearedin
buffer.Moredetailsaboutinventorymodeareasbelow.
1.ScanthebarcodetoenterInventoryMode
2.ScanthebarcodetoreturntoCommonMode
3.Scanthebarcodetocleardatainbuffer(forInventoryModeonly).
4.Scanthebarcodetouploaddatafrombuffer(forInventoryMode
only)
5.Scanthebarcodetouploadthenumberofscannedbarcodes(for
InventoryModeonly)
Note:
1) To use inventory mode, users just need scan “Enter Inventory
Mode”barcode;anddonothavetoscan“EnterSetup”barcode
beforethat.
2)Toendinventorymode,usersjustneedscan“ReturntoCommon
Mode”barcode.
FunctionSetupBarcodes
123
4567
8 9 10 11
12 13 14 15
16 17 18 19
20 21 22 23
24 25 26 27
28 29 30 31

EnterInventoryMode
（*）ReturntoCommonMode
ClearDatainBuffer(forInventoryModeonly)
DataUpload(forInventoryModeonly)
UploadtheNumberofscannedbarcodes(forInventoryModeonly)
FrequentlyUsedPrefix/SuffixBarcodes
Note:
1) More prefix/suffix barcodes are available at www.inateck.com.
Userscandownloadthemfromthesite.Foranyotherquestions,
pleasesendemailto[e-mail].
2) Scanning result will come with prefix/suffix after the setting.
Nevertheless,prefix/suffixcanbehiddenorrecovered.Tohide
prefix/suffix, scan “Enter Setup” barcode, “Hide Prefix/Suffix”
barcode,andthen“ExitwithSave”barcode.Torecoverprefix/suffix,
scan“EnterSetup”barcode,“RecoverPrefix/Suffix”barcode,and
then“ExitwithSave”barcode.
DeleteCharacter(s)onOutputResult
InateckP6canhelpusersdeletecharacter(s)onoutputresult,either
beginning characters or the ending ones. 0 to 9 digits can be
deleted.Asdefaultsetting,nocharacter,orsay0digitisdeletedas
outputresult.Moredetailsareasbelow.
1.Scan“EnterSetup”Barcode
2.Scan“DeleteBeginningCharacter(s)”Barcodeor“DeleteEnding
Character(s)”Barcode
3.Scanthedigit(s)barcodetobedeleted.
4.Scan“ExitwithSave”Barcodetoendthesetting
Note:Refertothesettingof“delete0digitcharacter”ifnocharacter
shouldbedeleted.
InventoryMode
Users mayuseinventorymodeto keepscannedbarcodes in the
buffer of Inateck P6, and upload them to computer in batches.
Under inventory mode users are not restricted to the time and
locationwhenuploaddata.Ofcourse,historydatacanbeclearedin
buffer.Moredetailsaboutinventorymodeareasbelow.
1.ScanthebarcodetoenterInventoryMode
2.ScanthebarcodetoreturntoCommonMode
3.Scanthebarcodetocleardatainbuffer(forInventoryModeonly).
4.Scanthebarcodetouploaddatafrombuffer(forInventoryMode
only)
5.Scanthebarcodetouploadthenumberofscannedbarcodes(for
InventoryModeonly)
Note:
1) To use inventory mode, users just need scan “Enter Inventory
Mode”barcode;anddonothavetoscan“EnterSetup”barcode
beforethat.
2)Toendinventorymode,usersjustneedscan“ReturntoCommon
Mode”barcode.
FunctionSetupBarcodes
123
4567
8 9 10 11
12 13 14 15
16 17 18 19
20 21 22 23
24 25 26 27
28 29 30 31