Inateck BCST-20 User manual

► USB wired + 2.4G wireless communication
► Built-in FLASH memory, supports breakpoint resume
► Can store 2600 pieces Code-128 codes under offline state
► Supports Windows XP, Win7/8/10, Wince, mobile OS PC
BCST-20 Barcode Scanner
Quick Start Guide
Packing list:
BCST-20*1unit
USB cable*1pce
Wireless Adapter*1pce
Quick Start Guide
Note: The device is not equipped with the charger, please charge the device
via USB output charging equipment.
BCST-20
Appearance:
BCST-20 Barcode Scanner Overview
BCST-20 integrates high-performance processor and decoding board, it has fast decoding, high-precision reading ability, and high anti-interference ability. It can easily read barcodes on
paper, goods and other media. The DOF has greatly improvement with similar products, also it has highly scanning speed, powerful reading ability with high accuracy.
1
Scan the“Enter Setup”
barcode
2.4G Wireless mode USB Wired mode
USB Port
Power
You can change your
scanner setting by scan
a certain barcode.
Scan the “Exit with Save”
barcode to finish the
setting.
Functions Setup:
BCST-20 Barcode Scanner change all the default functions setup through reading the setup
barcodes.
Buffer data purge
Manual data upload
Summarising of uploaded data entry quantity
Quit offline mode
2Offline Mode
If you are heading for a working area which lies outside the
Bluetooth signal range, you may activate the offline mode
of the scanner, following the steps described below. Under
this enhanced offline mode, all scanned data will be stored
directly into the buffer memory of the device. Furthermore,
the data entries will be permanently saved in the buffer
memory prior to the manual upload into the working
station, so that you may upload them time and again to
your liking.
Due to the fact that the data entries will be automatically
wiped from the buffer memory during upload, a data loss is
possible when malfunctions occur during upload, e.g. if the
working station suffers a unanticipated system shut down.
An operation in offline mode is strongly recommended
under the following scenarios:
1) During the scanning process, the device often leaves
the Bluetooth signal range;
2) Due to a high quantity of blocking objects, the Bluetooth
signal’s stability can’t be ensured.
1. By scanning the following barcode, the offline mode
will be activated.
4Prefix and Suffix Setting
1. Scan the “Enter Setup” barcode
2. Scan the “Prefix Setting” or “Suffix Setting” scanner
3. Scan certain barcodes sequentially to generate your
own prefix/suffix. Example: If you want to add “#” as
prefix or suffix, according to the barcode list provided on
our website, you need to scan the “3” barcode first and
then scan the “5” barcode.
(Please refer to www.inateck.com for the number and
symbol barcode list.)
4. Scan the “Exit with Save” barcode.
Offline mode activation
2. By scanning the following barcode, all data in the buffer
memory will be deleted (only in offline mode).
3. By scanning the following barcode, all data entries in the
buffer memory can be manually uploaded after reconnect-
ing to the working station (only in offline mode).
4. By scanning the following barcode, the gross quantity of the
uploaded data entries will be summarised (only in offline
mode).
5. By scanning the following barcode, the device leaves the
offline mode, normal mode will be reinitialised.
Exit With save
Performance Characteristics
Light Source (Laser)
Decode Capability
Resolution
Nominal Working Distance
Decode Rate
Scan width
Decode mode
Scan mode
Print Contrast Minimum
Scan angles
Cylinder Horizontal Scan
Indication
Radio Range
Interfaces Supported
Processor
EEPROM
Wireless Communication
Battery
Bluetooth Operating Frequency
Bluetooth transmission Power
Laser LED 650+/-20nm
Codabar, Code 93, MSI, Code 128, UCC/ EAN-128, Code 39, EAN-8, EAN-13, UPC-A,
UPC-E, ISBN, Industrial 25, Interleaved 25, Standard 25, 2/5 Matrix, USPS, FedEx
3mil
6~30cm
100 decodes per second
30mm
Single-Line Aiming
Manual mode
30%
Roll 30° Pitch 75° Yaw65°
Diameter 35mm
Beeper, LED
10m Visual range
USB2.0
ARM 772MHz
256K, can store thousands of barcodes
2.4G Wireless transmission
1800mAh lithium battery
2402-2480MHz
4dBm
3Keyboard Language Setting
Read ‘Enter setup’ Barcode - ‘Select your keyboard language’
- Exit With save - Change your PC language as selected.
Read ‘Enter setup’ Barcode
Enter setup
Prefix Setting
Suffix Setting
Italian Keyboard
US Keyboard
German Keyboard
French Keyboard
Spainish Keyboard
Exit With save
Eg: Switching to German keyboard
Read ‘Enter setup’ Barcode German Keyboard
Exit With save

► USB wired + 2.4G wireless communication
► Built-in FLASH memory, supports breakpoint resume
► Can store 2600 pieces Code-128 codes under offline state
► Supports Windows XP, Win7/8/10, Wince, mobile OS PC
BCST-20 Barcode Scanner
Quick Start Guide
Packing list:
BCST-20*1unit
USB cable*1pce
Wireless Adapter*1pce
Quick Start Guide
Note: The device is not equipped with the charger, please charge the device
via USB output charging equipment.
BCST-20
Appearance:
BCST-20 Barcode Scanner Overview
BCST-20 integrates high-performance processor and decoding board, it has fast decoding, high-precision reading ability, and high anti-interference ability. It can easily read barcodes on
paper, goods and other media. The DOF has greatly improvement with similar products, also it has highly scanning speed, powerful reading ability with high accuracy.
1
Scan the“Enter Setup”
barcode
2.4G Wireless mode USB Wired mode
USB Port
Power
You can change your
scanner setting by scan
a certain barcode.
Scan the “Exit with Save”
barcode to finish the
setting.
Functions Setup:
BCST-20 Barcode Scanner change all the default functions setup through reading the setup
barcodes.
Buffer data purge
Manual data upload
Summarising of uploaded data entry quantity
Quit offline mode
2Offline Mode
If you are heading for a working area which lies outside the
Bluetooth signal range, you may activate the offline mode
of the scanner, following the steps described below. Under
this enhanced offline mode, all scanned data will be stored
directly into the buffer memory of the device. Furthermore,
the data entries will be permanently saved in the buffer
memory prior to the manual upload into the working
station, so that you may upload them time and again to
your liking.
Due to the fact that the data entries will be automatically
wiped from the buffer memory during upload, a data loss is
possible when malfunctions occur during upload, e.g. if the
working station suffers a unanticipated system shut down.
An operation in offline mode is strongly recommended
under the following scenarios:
1) During the scanning process, the device often leaves
the Bluetooth signal range;
2) Due to a high quantity of blocking objects, the Bluetooth
signal’s stability can’t be ensured.
1. By scanning the following barcode, the offline mode
will be activated.
4Prefix and Suffix Setting
1. Scan the “Enter Setup” barcode
2. Scan the “Prefix Setting” or “Suffix Setting” scanner
3. Scan certain barcodes sequentially to generate your
own prefix/suffix. Example: If you want to add “#” as
prefix or suffix, according to the barcode list provided on
our website, you need to scan the “3” barcode first and
then scan the “5” barcode.
(Please refer to www.inateck.com for the number and
symbol barcode list.)
4. Scan the “Exit with Save” barcode.
Offline mode activation
2. By scanning the following barcode, all data in the buffer
memory will be deleted (only in offline mode).
3. By scanning the following barcode, all data entries in the
buffer memory can be manually uploaded after reconnect-
ing to the working station (only in offline mode).
4. By scanning the following barcode, the gross quantity of the
uploaded data entries will be summarised (only in offline
mode).
5. By scanning the following barcode, the device leaves the
offline mode, normal mode will be reinitialised.
Exit With save
Performance Characteristics
Light Source (Laser)
Decode Capability
Resolution
Nominal Working Distance
Decode Rate
Scan width
Decode mode
Scan mode
Print Contrast Minimum
Scan angles
Cylinder Horizontal Scan
Indication
Radio Range
Interfaces Supported
Processor
EEPROM
Wireless Communication
Battery
Bluetooth Operating Frequency
Bluetooth transmission Power
Laser LED 650+/-20nm
Codabar, Code 93, MSI, Code 128, UCC/ EAN-128, Code 39, EAN-8, EAN-13, UPC-A,
UPC-E, ISBN, Industrial 25, Interleaved 25, Standard 25, 2/5 Matrix, USPS, FedEx
3mil
6~30cm
100 decodes per second
30mm
Single-Line Aiming
Manual mode
30%
Roll 30° Pitch 75° Yaw65°
Diameter 35mm
Beeper, LED
10m Visual range
USB2.0
ARM 772MHz
256K, can store thousands of barcodes
2.4G Wireless transmission
1800mAh lithium battery
2402-2480MHz
4dBm
3Keyboard Language Setting
Read ‘Enter setup’ Barcode - ‘Select your keyboard language’
- Exit With save - Change your PC language as selected.
Read ‘Enter setup’ Barcode
Enter setup
Prefix Setting
Suffix Setting
Italian Keyboard
US Keyboard
German Keyboard
French Keyboard
Spainish Keyboard
Exit With save
Eg: Switching to German keyboard
Read ‘Enter setup’ Barcode German Keyboard
Exit With save

► USB wired + 2.4G wireless communication
► Built-in FLASH memory, supports breakpoint resume
► Can store 2600 pieces Code-128 codes under offline state
► Supports Windows XP, Win7/8/10, Wince, mobile OS PC
BCST-20 Barcode Scanner
Quick Start Guide
Packing list:
BCST-20*1unit
USB cable*1pce
Wireless Adapter*1pce
Quick Start Guide
Note: The device is not equipped with the charger, please charge the device
via USB output charging equipment.
BCST-20
Appearance:
BCST-20 Barcode Scanner Overview
BCST-20 integrates high-performance processor and decoding board, it has fast decoding, high-precision reading ability, and high anti-interference ability. It can easily read barcodes on
paper, goods and other media. The DOF has greatly improvement with similar products, also it has highly scanning speed, powerful reading ability with high accuracy.
1
Scan the“Enter Setup”
barcode
2.4G Wireless mode USB Wired mode
USB Port
Power
You can change your
scanner setting by scan
a certain barcode.
Scan the “Exit with Save”
barcode to finish the
setting.
Functions Setup:
BCST-20 Barcode Scanner change all the default functions setup through reading the setup
barcodes.
Buffer data purge
Manual data upload
Summarising of uploaded data entry quantity
Quit offline mode
2Offline Mode
If you are heading for a working area which lies outside the
Bluetooth signal range, you may activate the offline mode
of the scanner, following the steps described below. Under
this enhanced offline mode, all scanned data will be stored
directly into the buffer memory of the device. Furthermore,
the data entries will be permanently saved in the buffer
memory prior to the manual upload into the working
station, so that you may upload them time and again to
your liking.
Due to the fact that the data entries will be automatically
wiped from the buffer memory during upload, a data loss is
possible when malfunctions occur during upload, e.g. if the
working station suffers a unanticipated system shut down.
An operation in offline mode is strongly recommended
under the following scenarios:
1) During the scanning process, the device often leaves
the Bluetooth signal range;
2) Due to a high quantity of blocking objects, the Bluetooth
signal’s stability can’t be ensured.
1. By scanning the following barcode, the offline mode
will be activated.
4Prefix and Suffix Setting
1. Scan the “Enter Setup” barcode
2. Scan the “Prefix Setting” or “Suffix Setting” scanner
3. Scan certain barcodes sequentially to generate your
own prefix/suffix. Example: If you want to add “#” as
prefix or suffix, according to the barcode list provided on
our website, you need to scan the “3” barcode first and
then scan the “5” barcode.
(Please refer to www.inateck.com for the number and
symbol barcode list.)
4. Scan the “Exit with Save” barcode.
Offline mode activation
2. By scanning the following barcode, all data in the buffer
memory will be deleted (only in offline mode).
3. By scanning the following barcode, all data entries in the
buffer memory can be manually uploaded after reconnect-
ing to the working station (only in offline mode).
4. By scanning the following barcode, the gross quantity of the
uploaded data entries will be summarised (only in offline
mode).
5. By scanning the following barcode, the device leaves the
offline mode, normal mode will be reinitialised.
Exit With save
Performance Characteristics
Light Source (Laser)
Decode Capability
Resolution
Nominal Working Distance
Decode Rate
Scan width
Decode mode
Scan mode
Print Contrast Minimum
Scan angles
Cylinder Horizontal Scan
Indication
Radio Range
Interfaces Supported
Processor
EEPROM
Wireless Communication
Battery
Bluetooth Operating Frequency
Bluetooth transmission Power
Laser LED 650+/-20nm
Codabar, Code 93, MSI, Code 128, UCC/ EAN-128, Code 39, EAN-8, EAN-13, UPC-A,
UPC-E, ISBN, Industrial 25, Interleaved 25, Standard 25, 2/5 Matrix, USPS, FedEx
3mil
6~30cm
100 decodes per second
30mm
Single-Line Aiming
Manual mode
30%
Roll 30° Pitch 75° Yaw65°
Diameter 35mm
Beeper, LED
10m Visual range
USB2.0
ARM 772MHz
256K, can store thousands of barcodes
2.4G Wireless transmission
1800mAh lithium battery
2402-2480MHz
4dBm
3Keyboard Language Setting
Read ‘Enter setup’ Barcode - ‘Select your keyboard language’
- Exit With save - Change your PC language as selected.
Read ‘Enter setup’ Barcode
Enter setup
Prefix Setting
Suffix Setting
Italian Keyboard
US Keyboard
German Keyboard
French Keyboard
Spainish Keyboard
Exit With save
Eg: Switching to German keyboard
Read ‘Enter setup’ Barcode German Keyboard
Exit With save

► USB wired + 2.4G wireless communication
► Built-in FLASH memory, supports breakpoint resume
► Can store 2600 pieces Code-128 codes under offline state
► Supports Windows XP, Win7/8/10, Wince, mobile OS PC
BCST-20 Barcode Scanner
Quick Start Guide
Packing list:
BCST-20*1unit
USB cable*1pce
Wireless Adapter*1pce
Quick Start Guide
Note: The device is not equipped with the charger, please charge the device
via USB output charging equipment.
BCST-20
Appearance:
BCST-20 Barcode Scanner Overview
BCST-20 integrates high-performance processor and decoding board, it has fast decoding, high-precision reading ability, and high anti-interference ability. It can easily read barcodes on
paper, goods and other media. The DOF has greatly improvement with similar products, also it has highly scanning speed, powerful reading ability with high accuracy.
1
Scan the“Enter Setup”
barcode
2.4G Wireless mode USB Wired mode
USB Port
Power
You can change your
scanner setting by scan
a certain barcode.
Scan the “Exit with Save”
barcode to finish the
setting.
Functions Setup:
BCST-20 Barcode Scanner change all the default functions setup through reading the setup
barcodes.
Buffer data purge
Manual data upload
Summarising of uploaded data entry quantity
Quit offline mode
2Offline Mode
If you are heading for a working area which lies outside the
Bluetooth signal range, you may activate the offline mode
of the scanner, following the steps described below. Under
this enhanced offline mode, all scanned data will be stored
directly into the buffer memory of the device. Furthermore,
the data entries will be permanently saved in the buffer
memory prior to the manual upload into the working
station, so that you may upload them time and again to
your liking.
Due to the fact that the data entries will be automatically
wiped from the buffer memory during upload, a data loss is
possible when malfunctions occur during upload, e.g. if the
working station suffers a unanticipated system shut down.
An operation in offline mode is strongly recommended
under the following scenarios:
1) During the scanning process, the device often leaves
the Bluetooth signal range;
2) Due to a high quantity of blocking objects, the Bluetooth
signal’s stability can’t be ensured.
1. By scanning the following barcode, the offline mode
will be activated.
4Prefix and Suffix Setting
1. Scan the “Enter Setup” barcode
2. Scan the “Prefix Setting” or “Suffix Setting” scanner
3. Scan certain barcodes sequentially to generate your
own prefix/suffix. Example: If you want to add “#” as
prefix or suffix, according to the barcode list provided on
our website, you need to scan the “3” barcode first and
then scan the “5” barcode.
(Please refer to www.inateck.com for the number and
symbol barcode list.)
4. Scan the “Exit with Save” barcode.
Offline mode activation
2. By scanning the following barcode, all data in the buffer
memory will be deleted (only in offline mode).
3. By scanning the following barcode, all data entries in the
buffer memory can be manually uploaded after reconnect-
ing to the working station (only in offline mode).
4. By scanning the following barcode, the gross quantity of the
uploaded data entries will be summarised (only in offline
mode).
5. By scanning the following barcode, the device leaves the
offline mode, normal mode will be reinitialised.
Exit With save
Performance Characteristics
Light Source (Laser)
Decode Capability
Resolution
Nominal Working Distance
Decode Rate
Scan width
Decode mode
Scan mode
Print Contrast Minimum
Scan angles
Cylinder Horizontal Scan
Indication
Radio Range
Interfaces Supported
Processor
EEPROM
Wireless Communication
Battery
Bluetooth Operating Frequency
Bluetooth transmission Power
Laser LED 650+/-20nm
Codabar, Code 93, MSI, Code 128, UCC/ EAN-128, Code 39, EAN-8, EAN-13, UPC-A,
UPC-E, ISBN, Industrial 25, Interleaved 25, Standard 25, 2/5 Matrix, USPS, FedEx
3mil
6~30cm
100 decodes per second
30mm
Single-Line Aiming
Manual mode
30%
Roll 30° Pitch 75° Yaw65°
Diameter 35mm
Beeper, LED
10m Visual range
USB2.0
ARM 772MHz
256K, can store thousands of barcodes
2.4G Wireless transmission
1800mAh lithium battery
2402-2480MHz
4dBm
3Keyboard Language Setting
Read ‘Enter setup’ Barcode - ‘Select your keyboard language’
- Exit With save - Change your PC language as selected.
Read ‘Enter setup’ Barcode
Enter setup
Prefix Setting
Suffix Setting
Italian Keyboard
US Keyboard
German Keyboard
French Keyboard
Spainish Keyboard
Exit With save
Eg: Switching to German keyboard
Read ‘Enter setup’ Barcode German Keyboard
Exit With save

► USB wired + 2.4G wireless communication
► Built-in FLASH memory, supports breakpoint resume
► Can store 2600 pieces Code-128 codes under offline state
► Supports Windows XP, Win7/8/10, Wince, mobile OS PC
BCST-20 Barcode Scanner
Quick Start Guide
Packing list:
BCST-20*1unit
USB cable*1pce
Wireless Adapter*1pce
Quick Start Guide
Note: The device is not equipped with the charger, please charge the device
via USB output charging equipment.
BCST-20
Appearance:
BCST-20 Barcode Scanner Overview
BCST-20 integrates high-performance processor and decoding board, it has fast decoding, high-precision reading ability, and high anti-interference ability. It can easily read barcodes on
paper, goods and other media. The DOF has greatly improvement with similar products, also it has highly scanning speed, powerful reading ability with high accuracy.
1
Scan the“Enter Setup”
barcode
2.4G Wireless mode USB Wired mode
USB Port
Power
You can change your
scanner setting by scan
a certain barcode.
Scan the “Exit with Save”
barcode to finish the
setting.
Functions Setup:
BCST-20 Barcode Scanner change all the default functions setup through reading the setup
barcodes.
Buffer data purge
Manual data upload
Summarising of uploaded data entry quantity
Quit offline mode
2Offline Mode
If you are heading for a working area which lies outside the
Bluetooth signal range, you may activate the offline mode
of the scanner, following the steps described below. Under
this enhanced offline mode, all scanned data will be stored
directly into the buffer memory of the device. Furthermore,
the data entries will be permanently saved in the buffer
memory prior to the manual upload into the working
station, so that you may upload them time and again to
your liking.
Due to the fact that the data entries will be automatically
wiped from the buffer memory during upload, a data loss is
possible when malfunctions occur during upload, e.g. if the
working station suffers a unanticipated system shut down.
An operation in offline mode is strongly recommended
under the following scenarios:
1) During the scanning process, the device often leaves
the Bluetooth signal range;
2) Due to a high quantity of blocking objects, the Bluetooth
signal’s stability can’t be ensured.
1. By scanning the following barcode, the offline mode
will be activated.
4Prefix and Suffix Setting
1. Scan the “Enter Setup” barcode
2. Scan the “Prefix Setting” or “Suffix Setting” scanner
3. Scan certain barcodes sequentially to generate your
own prefix/suffix. Example: If you want to add “#” as
prefix or suffix, according to the barcode list provided on
our website, you need to scan the “3” barcode first and
then scan the “5” barcode.
(Please refer to www.inateck.com for the number and
symbol barcode list.)
4. Scan the “Exit with Save” barcode.
Offline mode activation
2. By scanning the following barcode, all data in the buffer
memory will be deleted (only in offline mode).
3. By scanning the following barcode, all data entries in the
buffer memory can be manually uploaded after reconnect-
ing to the working station (only in offline mode).
4. By scanning the following barcode, the gross quantity of the
uploaded data entries will be summarised (only in offline
mode).
5. By scanning the following barcode, the device leaves the
offline mode, normal mode will be reinitialised.
Exit With save
Performance Characteristics
Light Source (Laser)
Decode Capability
Resolution
Nominal Working Distance
Decode Rate
Scan width
Decode mode
Scan mode
Print Contrast Minimum
Scan angles
Cylinder Horizontal Scan
Indication
Radio Range
Interfaces Supported
Processor
EEPROM
Wireless Communication
Battery
Bluetooth Operating Frequency
Bluetooth transmission Power
Laser LED 650+/-20nm
Codabar, Code 93, MSI, Code 128, UCC/ EAN-128, Code 39, EAN-8, EAN-13, UPC-A,
UPC-E, ISBN, Industrial 25, Interleaved 25, Standard 25, 2/5 Matrix, USPS, FedEx
3mil
6~30cm
100 decodes per second
30mm
Single-Line Aiming
Manual mode
30%
Roll 30° Pitch 75° Yaw65°
Diameter 35mm
Beeper, LED
10m Visual range
USB2.0
ARM 772MHz
256K, can store thousands of barcodes
2.4G Wireless transmission
1800mAh lithium battery
2402-2480MHz
4dBm
3Keyboard Language Setting
Read ‘Enter setup’ Barcode - ‘Select your keyboard language’
- Exit With save - Change your PC language as selected.
Read ‘Enter setup’ Barcode
Enter setup
Prefix Setting
Suffix Setting
Italian Keyboard
US Keyboard
German Keyboard
French Keyboard
Spainish Keyboard
Exit With save
Eg: Switching to German keyboard
Read ‘Enter setup’ Barcode German Keyboard
Exit With save

► USB wired + 2.4G wireless communication
► Built-in FLASH memory, supports breakpoint resume
► Can store 2600 pieces Code-128 codes under offline state
► Supports Windows XP, Win7/8/10, Wince, mobile OS PC
BCST-20 Barcode Scanner
Quick Start Guide
Packing list:
BCST-20*1unit
USB cable*1pce
Wireless Adapter*1pce
Quick Start Guide
Note: The device is not equipped with the charger, please charge the device
via USB output charging equipment.
BCST-20
Appearance:
BCST-20 Barcode Scanner Overview
BCST-20 integrates high-performance processor and decoding board, it has fast decoding, high-precision reading ability, and high anti-interference ability. It can easily read barcodes on
paper, goods and other media. The DOF has greatly improvement with similar products, also it has highly scanning speed, powerful reading ability with high accuracy.
1
Scan the“Enter Setup”
barcode
2.4G Wireless mode USB Wired mode
USB Port
Power
You can change your
scanner setting by scan
a certain barcode.
Scan the “Exit with Save”
barcode to finish the
setting.
Functions Setup:
BCST-20 Barcode Scanner change all the default functions setup through reading the setup
barcodes.
Buffer data purge
Manual data upload
Summarising of uploaded data entry quantity
Quit offline mode
2Offline Mode
If you are heading for a working area which lies outside the
Bluetooth signal range, you may activate the offline mode
of the scanner, following the steps described below. Under
this enhanced offline mode, all scanned data will be stored
directly into the buffer memory of the device. Furthermore,
the data entries will be permanently saved in the buffer
memory prior to the manual upload into the working
station, so that you may upload them time and again to
your liking.
Due to the fact that the data entries will be automatically
wiped from the buffer memory during upload, a data loss is
possible when malfunctions occur during upload, e.g. if the
working station suffers a unanticipated system shut down.
An operation in offline mode is strongly recommended
under the following scenarios:
1) During the scanning process, the device often leaves
the Bluetooth signal range;
2) Due to a high quantity of blocking objects, the Bluetooth
signal’s stability can’t be ensured.
1. By scanning the following barcode, the offline mode
will be activated.
4Prefix and Suffix Setting
1. Scan the “Enter Setup” barcode
2. Scan the “Prefix Setting” or “Suffix Setting” scanner
3. Scan certain barcodes sequentially to generate your
own prefix/suffix. Example: If you want to add “#” as
prefix or suffix, according to the barcode list provided on
our website, you need to scan the “3” barcode first and
then scan the “5” barcode.
(Please refer to www.inateck.com for the number and
symbol barcode list.)
4. Scan the “Exit with Save” barcode.
Offline mode activation
2. By scanning the following barcode, all data in the buffer
memory will be deleted (only in offline mode).
3. By scanning the following barcode, all data entries in the
buffer memory can be manually uploaded after reconnect-
ing to the working station (only in offline mode).
4. By scanning the following barcode, the gross quantity of the
uploaded data entries will be summarised (only in offline
mode).
5. By scanning the following barcode, the device leaves the
offline mode, normal mode will be reinitialised.
Exit With save
Performance Characteristics
Light Source (Laser)
Decode Capability
Resolution
Nominal Working Distance
Decode Rate
Scan width
Decode mode
Scan mode
Print Contrast Minimum
Scan angles
Cylinder Horizontal Scan
Indication
Radio Range
Interfaces Supported
Processor
EEPROM
Wireless Communication
Battery
Bluetooth Operating Frequency
Bluetooth transmission Power
Laser LED 650+/-20nm
Codabar, Code 93, MSI, Code 128, UCC/ EAN-128, Code 39, EAN-8, EAN-13, UPC-A,
UPC-E, ISBN, Industrial 25, Interleaved 25, Standard 25, 2/5 Matrix, USPS, FedEx
3mil
6~30cm
100 decodes per second
30mm
Single-Line Aiming
Manual mode
30%
Roll 30° Pitch 75° Yaw65°
Diameter 35mm
Beeper, LED
10m Visual range
USB2.0
ARM 772MHz
256K, can store thousands of barcodes
2.4G Wireless transmission
1800mAh lithium battery
2402-2480MHz
4dBm
3Keyboard Language Setting
Read ‘Enter setup’ Barcode - ‘Select your keyboard language’
- Exit With save - Change your PC language as selected.
Read ‘Enter setup’ Barcode
Enter setup
Prefix Setting
Suffix Setting
Italian Keyboard
US Keyboard
German Keyboard
French Keyboard
Spainish Keyboard
Exit With save
Eg: Switching to German keyboard
Read ‘Enter setup’ Barcode German Keyboard
Exit With save

► USB wired + 2.4G wireless communication
► Built-in FLASH memory, supports breakpoint resume
► Can store 2600 pieces Code-128 codes under offline state
► Supports Windows XP, Win7/8/10, Wince, mobile OS PC
BCST-20 Barcode Scanner
Quick Start Guide
Packing list:
BCST-20*1unit
USB cable*1pce
Wireless Adapter*1pce
Quick Start Guide
Note: The device is not equipped with the charger, please charge the device
via USB output charging equipment.
BCST-20
Appearance:
BCST-20 Barcode Scanner Overview
BCST-20 integrates high-performance processor and decoding board, it has fast decoding, high-precision reading ability, and high anti-interference ability. It can easily read barcodes on
paper, goods and other media. The DOF has greatly improvement with similar products, also it has highly scanning speed, powerful reading ability with high accuracy.
1
Scan the“Enter Setup”
barcode
2.4G Wireless mode USB Wired mode
USB Port
Power
You can change your
scanner setting by scan
a certain barcode.
Scan the “Exit with Save”
barcode to finish the
setting.
Functions Setup:
BCST-20 Barcode Scanner change all the default functions setup through reading the setup
barcodes.
Buffer data purge
Manual data upload
Summarising of uploaded data entry quantity
Quit offline mode
2Offline Mode
If you are heading for a working area which lies outside the
Bluetooth signal range, you may activate the offline mode
of the scanner, following the steps described below. Under
this enhanced offline mode, all scanned data will be stored
directly into the buffer memory of the device. Furthermore,
the data entries will be permanently saved in the buffer
memory prior to the manual upload into the working
station, so that you may upload them time and again to
your liking.
Due to the fact that the data entries will be automatically
wiped from the buffer memory during upload, a data loss is
possible when malfunctions occur during upload, e.g. if the
working station suffers a unanticipated system shut down.
An operation in offline mode is strongly recommended
under the following scenarios:
1) During the scanning process, the device often leaves
the Bluetooth signal range;
2) Due to a high quantity of blocking objects, the Bluetooth
signal’s stability can’t be ensured.
1. By scanning the following barcode, the offline mode
will be activated.
4Prefix and Suffix Setting
1. Scan the “Enter Setup” barcode
2. Scan the “Prefix Setting” or “Suffix Setting” scanner
3. Scan certain barcodes sequentially to generate your
own prefix/suffix. Example: If you want to add “#” as
prefix or suffix, according to the barcode list provided on
our website, you need to scan the “3” barcode first and
then scan the “5” barcode.
(Please refer to www.inateck.com for the number and
symbol barcode list.)
4. Scan the “Exit with Save” barcode.
Offline mode activation
2. By scanning the following barcode, all data in the buffer
memory will be deleted (only in offline mode).
3. By scanning the following barcode, all data entries in the
buffer memory can be manually uploaded after reconnect-
ing to the working station (only in offline mode).
4. By scanning the following barcode, the gross quantity of the
uploaded data entries will be summarised (only in offline
mode).
5. By scanning the following barcode, the device leaves the
offline mode, normal mode will be reinitialised.
Exit With save
Performance Characteristics
Light Source (Laser)
Decode Capability
Resolution
Nominal Working Distance
Decode Rate
Scan width
Decode mode
Scan mode
Print Contrast Minimum
Scan angles
Cylinder Horizontal Scan
Indication
Radio Range
Interfaces Supported
Processor
EEPROM
Wireless Communication
Battery
Bluetooth Operating Frequency
Bluetooth transmission Power
Laser LED 650+/-20nm
Codabar, Code 93, MSI, Code 128, UCC/ EAN-128, Code 39, EAN-8, EAN-13, UPC-A,
UPC-E, ISBN, Industrial 25, Interleaved 25, Standard 25, 2/5 Matrix, USPS, FedEx
3mil
6~30cm
100 decodes per second
30mm
Single-Line Aiming
Manual mode
30%
Roll 30° Pitch 75° Yaw65°
Diameter 35mm
Beeper, LED
10m Visual range
USB2.0
ARM 772MHz
256K, can store thousands of barcodes
2.4G Wireless transmission
1800mAh lithium battery
2402-2480MHz
4dBm
3Keyboard Language Setting
Read ‘Enter setup’ Barcode - ‘Select your keyboard language’
- Exit With save - Change your PC language as selected.
Read ‘Enter setup’ Barcode
Enter setup
Prefix Setting
Suffix Setting
Italian Keyboard
US Keyboard
German Keyboard
French Keyboard
Spainish Keyboard
Exit With save
Eg: Switching to German keyboard
Read ‘Enter setup’ Barcode German Keyboard
Exit With save

► USB wired + 2.4G wireless communication
► Built-in FLASH memory, supports breakpoint resume
► Can store 2600 pieces Code-128 codes under offline state
► Supports Windows XP, Win7/8/10, Wince, mobile OS PC
BCST-20 Barcode Scanner
Quick Start Guide
Packing list:
BCST-20*1unit
USB cable*1pce
Wireless Adapter*1pce
Quick Start Guide
Note: The device is not equipped with the charger, please charge the device
via USB output charging equipment.
BCST-20
Appearance:
BCST-20 Barcode Scanner Overview
BCST-20 integrates high-performance processor and decoding board, it has fast decoding, high-precision reading ability, and high anti-interference ability. It can easily read barcodes on
paper, goods and other media. The DOF has greatly improvement with similar products, also it has highly scanning speed, powerful reading ability with high accuracy.
1
Scan the“Enter Setup”
barcode
2.4G Wireless mode USB Wired mode
USB Port
Power
You can change your
scanner setting by scan
a certain barcode.
Scan the “Exit with Save”
barcode to finish the
setting.
Functions Setup:
BCST-20 Barcode Scanner change all the default functions setup through reading the setup
barcodes.
Buffer data purge
Manual data upload
Summarising of uploaded data entry quantity
Quit offline mode
2Offline Mode
If you are heading for a working area which lies outside the
Bluetooth signal range, you may activate the offline mode
of the scanner, following the steps described below. Under
this enhanced offline mode, all scanned data will be stored
directly into the buffer memory of the device. Furthermore,
the data entries will be permanently saved in the buffer
memory prior to the manual upload into the working
station, so that you may upload them time and again to
your liking.
Due to the fact that the data entries will be automatically
wiped from the buffer memory during upload, a data loss is
possible when malfunctions occur during upload, e.g. if the
working station suffers a unanticipated system shut down.
An operation in offline mode is strongly recommended
under the following scenarios:
1) During the scanning process, the device often leaves
the Bluetooth signal range;
2) Due to a high quantity of blocking objects, the Bluetooth
signal’s stability can’t be ensured.
1. By scanning the following barcode, the offline mode
will be activated.
4Prefix and Suffix Setting
1. Scan the “Enter Setup” barcode
2. Scan the “Prefix Setting” or “Suffix Setting” scanner
3. Scan certain barcodes sequentially to generate your
own prefix/suffix. Example: If you want to add “#” as
prefix or suffix, according to the barcode list provided on
our website, you need to scan the “3” barcode first and
then scan the “5” barcode.
(Please refer to www.inateck.com for the number and
symbol barcode list.)
4. Scan the “Exit with Save” barcode.
Offline mode activation
2. By scanning the following barcode, all data in the buffer
memory will be deleted (only in offline mode).
3. By scanning the following barcode, all data entries in the
buffer memory can be manually uploaded after reconnect-
ing to the working station (only in offline mode).
4. By scanning the following barcode, the gross quantity of the
uploaded data entries will be summarised (only in offline
mode).
5. By scanning the following barcode, the device leaves the
offline mode, normal mode will be reinitialised.
Exit With save
Performance Characteristics
Light Source (Laser)
Decode Capability
Resolution
Nominal Working Distance
Decode Rate
Scan width
Decode mode
Scan mode
Print Contrast Minimum
Scan angles
Cylinder Horizontal Scan
Indication
Radio Range
Interfaces Supported
Processor
EEPROM
Wireless Communication
Battery
Bluetooth Operating Frequency
Bluetooth transmission Power
Laser LED 650+/-20nm
Codabar, Code 93, MSI, Code 128, UCC/ EAN-128, Code 39, EAN-8, EAN-13, UPC-A,
UPC-E, ISBN, Industrial 25, Interleaved 25, Standard 25, 2/5 Matrix, USPS, FedEx
3mil
6~30cm
100 decodes per second
30mm
Single-Line Aiming
Manual mode
30%
Roll 30° Pitch 75° Yaw65°
Diameter 35mm
Beeper, LED
10m Visual range
USB2.0
ARM 772MHz
256K, can store thousands of barcodes
2.4G Wireless transmission
1800mAh lithium battery
2402-2480MHz
4dBm
3Keyboard Language Setting
Read ‘Enter setup’ Barcode - ‘Select your keyboard language’
- Exit With save - Change your PC language as selected.
Read ‘Enter setup’ Barcode
Enter setup
Prefix Setting
Suffix Setting
Italian Keyboard
US Keyboard
German Keyboard
French Keyboard
Spainish Keyboard
Exit With save
Eg: Switching to German keyboard
Read ‘Enter setup’ Barcode German Keyboard
Exit With save

► USB wired + 2.4G wireless communication
► Built-in FLASH memory, supports breakpoint resume
► Can store 2600 pieces Code-128 codes under offline state
► Supports Windows XP, Win7/8/10, Wince, mobile OS PC
BCST-20 Barcode Scanner
Quick Start Guide
Packing list:
BCST-20*1unit
USB cable*1pce
Wireless Adapter*1pce
Quick Start Guide
Note: The device is not equipped with the charger, please charge the device
via USB output charging equipment.
BCST-20
Appearance:
BCST-20 Barcode Scanner Overview
BCST-20 integrates high-performance processor and decoding board, it has fast decoding, high-precision reading ability, and high anti-interference ability. It can easily read barcodes on
paper, goods and other media. The DOF has greatly improvement with similar products, also it has highly scanning speed, powerful reading ability with high accuracy.
1
Scan the“Enter Setup”
barcode
2.4G Wireless mode USB Wired mode
USB Port
Power
You can change your
scanner setting by scan
a certain barcode.
Scan the “Exit with Save”
barcode to finish the
setting.
Functions Setup:
BCST-20 Barcode Scanner change all the default functions setup through reading the setup
barcodes.
Buffer data purge
Manual data upload
Summarising of uploaded data entry quantity
Quit offline mode
2Offline Mode
If you are heading for a working area which lies outside the
Bluetooth signal range, you may activate the offline mode
of the scanner, following the steps described below. Under
this enhanced offline mode, all scanned data will be stored
directly into the buffer memory of the device. Furthermore,
the data entries will be permanently saved in the buffer
memory prior to the manual upload into the working
station, so that you may upload them time and again to
your liking.
Due to the fact that the data entries will be automatically
wiped from the buffer memory during upload, a data loss is
possible when malfunctions occur during upload, e.g. if the
working station suffers a unanticipated system shut down.
An operation in offline mode is strongly recommended
under the following scenarios:
1) During the scanning process, the device often leaves
the Bluetooth signal range;
2) Due to a high quantity of blocking objects, the Bluetooth
signal’s stability can’t be ensured.
1. By scanning the following barcode, the offline mode
will be activated.
4Prefix and Suffix Setting
1. Scan the “Enter Setup” barcode
2. Scan the “Prefix Setting” or “Suffix Setting” scanner
3. Scan certain barcodes sequentially to generate your
own prefix/suffix. Example: If you want to add “#” as
prefix or suffix, according to the barcode list provided on
our website, you need to scan the “3” barcode first and
then scan the “5” barcode.
(Please refer to www.inateck.com for the number and
symbol barcode list.)
4. Scan the “Exit with Save” barcode.
Offline mode activation
2. By scanning the following barcode, all data in the buffer
memory will be deleted (only in offline mode).
3. By scanning the following barcode, all data entries in the
buffer memory can be manually uploaded after reconnect-
ing to the working station (only in offline mode).
4. By scanning the following barcode, the gross quantity of the
uploaded data entries will be summarised (only in offline
mode).
5. By scanning the following barcode, the device leaves the
offline mode, normal mode will be reinitialised.
Exit With save
Performance Characteristics
Light Source (Laser)
Decode Capability
Resolution
Nominal Working Distance
Decode Rate
Scan width
Decode mode
Scan mode
Print Contrast Minimum
Scan angles
Cylinder Horizontal Scan
Indication
Radio Range
Interfaces Supported
Processor
EEPROM
Wireless Communication
Battery
Bluetooth Operating Frequency
Bluetooth transmission Power
Laser LED 650+/-20nm
Codabar, Code 93, MSI, Code 128, UCC/ EAN-128, Code 39, EAN-8, EAN-13, UPC-A,
UPC-E, ISBN, Industrial 25, Interleaved 25, Standard 25, 2/5 Matrix, USPS, FedEx
3mil
6~30cm
100 decodes per second
30mm
Single-Line Aiming
Manual mode
30%
Roll 30° Pitch 75° Yaw65°
Diameter 35mm
Beeper, LED
10m Visual range
USB2.0
ARM 772MHz
256K, can store thousands of barcodes
2.4G Wireless transmission
1800mAh lithium battery
2402-2480MHz
4dBm
3Keyboard Language Setting
Read ‘Enter setup’ Barcode - ‘Select your keyboard language’
- Exit With save - Change your PC language as selected.
Read ‘Enter setup’ Barcode
Enter setup
Prefix Setting
Suffix Setting
Italian Keyboard
US Keyboard
German Keyboard
French Keyboard
Spainish Keyboard
Exit With save
Eg: Switching to German keyboard
Read ‘Enter setup’ Barcode German Keyboard
Exit With save

7Features
1. Supports a wide range of barcode types. FedEx and USPS
barcodes are all supported.
2. Anti-crash and anti-shock design.
3. Ergonomic design.Up to 3 million keystroke life expectancy.
4. Unrivalled battery life.
5. Press to scan - powered by deep sleep mode.
6. USB mode: 64 bit barcodes. 2.4G wireless mode: 57 bit
barcodes.
7. Prefix and suffix are allowed to be added. Reset to factory
default settings by scanning the “Factory Reset” barcode.
9Support
8FAQ
1. Some barcodes cannot be read, why?
a. Dirty or unclear barcodes might not be read.
b. Digital barcodes displayed on phones, computers or
tablets cannot be read.
c. The possible reason is that the setting for some
barcode types are not commonly used is off by
default. You need to activate a specific barcode type
to get it to work. Please feel free to contact our
Customer Service Team for further assistance if you
don't know the exact type of barcode that you are
referring to.
2. Is there any barcodes for apply or remove Enter for
suffix?
Yes, you can refer to the Common Function Barcodes
to reverse the setting.
3. The data cannot be sent to my computer or cellphone.
Why?
Please make sure if you have turned on the offline
mode. Because it will store your scans internally
instead of instantly transmitting them to the connected
device. You need to scan the "Manual data upload"
barcode to send the scanned codes to your connected
device.
4. Is the device compatible with android devices?
Yes，For Android User: an OTG Adapter is needed for
devices without standard USB.
5. How to solve the messy code problem encountered while
using other foreign languages?
The default language is English. Please refer to
“Language Setting” chapter to change the setting.
6. How to delete the extra charater in the prefix or suffix?
a. Scan code Prefix or Suffix Setting,
b. Scan code“1”“2”“7” sequentially, then scan code "Exit
with Save"
Note
If you receive an error of unable to transfer data via the
wireless connection (Not applicable for the Offline Mode),
please re-pair the scanner using the following steps. Please
bear in mind that this process may take 3-15 seconds.
Plug the 2.4G adapter
into your PC
Read “Enter Setup” Read “2.4G pairing”
For any inquiries or comments concerning our products, please
send an email to [email protected], and we will respond
to you as soon as possible.
www.inateck.com
5Common function Barcodes
Enter Setup Exit with Save
Exit without Save Factory Reset
Do not Apply Enter for suffix (*) Apply Enter for suffix
Apply Tab for suffix Exit Auto Power Off
Germany
Tel.: [phone] Fax.: [phone]
Phone hours: Weekdays 9 AM-5 PM (CET)
Email: [e-mail]
Web: http://www.inateck.com/de/
Addr.: F&M TECHNOLOGY GmbH, Montgolfierstraße 6,
04509 Wiedemar
Company of License Holder
Shenzhen Licheng Technology Co,.Ltd
Add: Warehouse B, 1F, Building B, Dezhong Industrial Park,
No.11 Shibei Road,
Bantian Street, Longgang District, Shenzhen, Guangdong,
518000, China Tel: [phone]
Manufacturer Information
Shenzhen Lixin Technology Co,.Ltd
Add: 1F, Building B , Dezhong Industrial Park, No.11 Shibei
Road, Bantian Street,
Longgang District, Shenzhen, Guangdong, 518000, China
Tel: [phone]
USA
Tel.: [phone]
Phone hours: Weekdays 9 AM to 5 PM (EST)
Email: [e-mail]
Web: www.inateck.com
Addr.: Inateck Technology Inc, 6045 Harrison Drive Suite 6，
Las Vegas, Nevada 89120
Contact Information
Enable Auto-induction Mode
2.4G pairing
2.4G pairing
Note:
1. If you want to setup the function of BCST-20. Read ‘Enter
Setup’ barcode, then ‘Function Setup’ barcode, and read ‘Exit
with Save’ at last.
2. Please remove the power and USB cable under thunderstorm
weather, to avoid damage from thunder and lightning.
3. Away heat source, keep ventilating.
4. Pay attention to waterproof during storage, transportation and
running.
LED lndicators
Indicator Colour Meaning
Blue LED on (1s) and off quickly
Green, Flashing (On/Off ratio 1:1)
Blue, Flashing (On/Off ratio 20ms:3s)
Red, Charging indicator
One short beep, high tone
One long beep, low tone
Two short beeps, high tone
Three short beeps, tone descending from high to low
Three short beeps, tone ascending from low to high
Read barcode, with blue LED on (1s) and off quickly
Configuration error, with purple flashing; Or transmit buffer full, with green LED
on and off quickly
Power off
Enter or Exit Setting mode, with green LED flashing
Configuration correct, with green LED flashing
Good Read, with one short beep (high tone)
Indicates the BCST-20 Scanner in Setting mode
Indicates the BCST-20 Scanner establish a wireless connection successfully
The red indicator will light during charging, and off when full charged.
Beeper
Beeping Meaning
Enter setup
6Function Setup Barcodes
(*) Enable Code bar
Enable Industral 25
(*) Enable Interleaved 25
Enable Matrix 25
(*) Enable Standard 25
Disable Interleaved 25
(*) Disable Industrial 25
Disable Code bar
(*) Disable Matrix 25
Disable Standard 25
(*) Enable Code 39 Disable Code 39
(*) Enable Code 93
Disable EAN-13
Disable EAN-8
Disable Code 128
(*) Enable Code 128
(*) Enable EAN-8
Disable Code 93
(*) Enable EAN-13
(*) Enable UPC-E Disable UPC-E
Enable MSI (*) Disable MSI
Exit with Save Enter Setup
(Note: the barcode with * is default setting of BCST-20)

7Features
1. Supports a wide range of barcode types. FedEx and USPS
barcodes are all supported.
2. Anti-crash and anti-shock design.
3. Ergonomic design.Up to 3 million keystroke life expectancy.
4. Unrivalled battery life.
5. Press to scan - powered by deep sleep mode.
6. USB mode: 64 bit barcodes. 2.4G wireless mode: 57 bit
barcodes.
7. Prefix and suffix are allowed to be added. Reset to factory
default settings by scanning the “Factory Reset” barcode.
9Support
8FAQ
1. Some barcodes cannot be read, why?
a. Dirty or unclear barcodes might not be read.
b. Digital barcodes displayed on phones, computers or
tablets cannot be read.
c. The possible reason is that the setting for some
barcode types are not commonly used is off by
default. You need to activate a specific barcode type
to get it to work. Please feel free to contact our
Customer Service Team for further assistance if you
don't know the exact type of barcode that you are
referring to.
2. Is there any barcodes for apply or remove Enter for
suffix?
Yes, you can refer to the Common Function Barcodes
to reverse the setting.
3. The data cannot be sent to my computer or cellphone.
Why?
Please make sure if you have turned on the offline
mode. Because it will store your scans internally
instead of instantly transmitting them to the connected
device. You need to scan the "Manual data upload"
barcode to send the scanned codes to your connected
device.
4. Is the device compatible with android devices?
Yes，For Android User: an OTG Adapter is needed for
devices without standard USB.
5. How to solve the messy code problem encountered while
using other foreign languages?
The default language is English. Please refer to
“Language Setting” chapter to change the setting.
6. How to delete the extra charater in the prefix or suffix?
a. Scan code Prefix or Suffix Setting,
b. Scan code“1”“2”“7” sequentially, then scan code "Exit
with Save"
Note
If you receive an error of unable to transfer data via the
wireless connection (Not applicable for the Offline Mode),
please re-pair the scanner using the following steps. Please
bear in mind that this process may take 3-15 seconds.
Plug the 2.4G adapter
into your PC
Read “Enter Setup” Read “2.4G pairing”
For any inquiries or comments concerning our products, please
send an email to [email protected], and we will respond
to you as soon as possible.
www.inateck.com
5Common function Barcodes
Enter Setup Exit with Save
Exit without Save Factory Reset
Do not Apply Enter for suffix (*) Apply Enter for suffix
Apply Tab for suffix Exit Auto Power Off
Germany
Tel.: [phone] Fax.: [phone]
Phone hours: Weekdays 9 AM-5 PM (CET)
Email: [e-mail]
Web: http://www.inateck.com/de/
Addr.: F&M TECHNOLOGY GmbH, Montgolfierstraße 6,
04509 Wiedemar
Company of License Holder
Shenzhen Licheng Technology Co,.Ltd
Add: Warehouse B, 1F, Building B, Dezhong Industrial Park,
No.11 Shibei Road,
Bantian Street, Longgang District, Shenzhen, Guangdong,
518000, China Tel: [phone]
Manufacturer Information
Shenzhen Lixin Technology Co,.Ltd
Add: 1F, Building B , Dezhong Industrial Park, No.11 Shibei
Road, Bantian Street,
Longgang District, Shenzhen, Guangdong, 518000, China
Tel: [phone]
USA
Tel.: [phone]
Phone hours: Weekdays 9 AM to 5 PM (EST)
Email: [e-mail]
Web: www.inateck.com
Addr.: Inateck Technology Inc, 6045 Harrison Drive Suite 6，
Las Vegas, Nevada 89120
Contact Information
Enable Auto-induction Mode
2.4G pairing
2.4G pairing
Note:
1. If you want to setup the function of BCST-20. Read ‘Enter
Setup’ barcode, then ‘Function Setup’ barcode, and read ‘Exit
with Save’ at last.
2. Please remove the power and USB cable under thunderstorm
weather, to avoid damage from thunder and lightning.
3. Away heat source, keep ventilating.
4. Pay attention to waterproof during storage, transportation and
running.
LED lndicators
Indicator Colour Meaning
Blue LED on (1s) and off quickly
Green, Flashing (On/Off ratio 1:1)
Blue, Flashing (On/Off ratio 20ms:3s)
Red, Charging indicator
One short beep, high tone
One long beep, low tone
Two short beeps, high tone
Three short beeps, tone descending from high to low
Three short beeps, tone ascending from low to high
Read barcode, with blue LED on (1s) and off quickly
Configuration error, with purple flashing; Or transmit buffer full, with green LED
on and off quickly
Power off
Enter or Exit Setting mode, with green LED flashing
Configuration correct, with green LED flashing
Good Read, with one short beep (high tone)
Indicates the BCST-20 Scanner in Setting mode
Indicates the BCST-20 Scanner establish a wireless connection successfully
The red indicator will light during charging, and off when full charged.
Beeper
Beeping Meaning
Enter setup
6Function Setup Barcodes
(*) Enable Code bar
Enable Industral 25
(*) Enable Interleaved 25
Enable Matrix 25
(*) Enable Standard 25
Disable Interleaved 25
(*) Disable Industrial 25
Disable Code bar
(*) Disable Matrix 25
Disable Standard 25
(*) Enable Code 39 Disable Code 39
(*) Enable Code 93
Disable EAN-13
Disable EAN-8
Disable Code 128
(*) Enable Code 128
(*) Enable EAN-8
Disable Code 93
(*) Enable EAN-13
(*) Enable UPC-E Disable UPC-E
Enable MSI (*) Disable MSI
Exit with Save Enter Setup
(Note: the barcode with * is default setting of BCST-20)

7Features
1. Supports a wide range of barcode types. FedEx and USPS
barcodes are all supported.
2. Anti-crash and anti-shock design.
3. Ergonomic design.Up to 3 million keystroke life expectancy.
4. Unrivalled battery life.
5. Press to scan - powered by deep sleep mode.
6. USB mode: 64 bit barcodes. 2.4G wireless mode: 57 bit
barcodes.
7. Prefix and suffix are allowed to be added. Reset to factory
default settings by scanning the “Factory Reset” barcode.
9Support
8FAQ
1. Some barcodes cannot be read, why?
a. Dirty or unclear barcodes might not be read.
b. Digital barcodes displayed on phones, computers or
tablets cannot be read.
c. The possible reason is that the setting for some
barcode types are not commonly used is off by
default. You need to activate a specific barcode type
to get it to work. Please feel free to contact our
Customer Service Team for further assistance if you
don't know the exact type of barcode that you are
referring to.
2. Is there any barcodes for apply or remove Enter for
suffix?
Yes, you can refer to the Common Function Barcodes
to reverse the setting.
3. The data cannot be sent to my computer or cellphone.
Why?
Please make sure if you have turned on the offline
mode. Because it will store your scans internally
instead of instantly transmitting them to the connected
device. You need to scan the "Manual data upload"
barcode to send the scanned codes to your connected
device.
4. Is the device compatible with android devices?
Yes，For Android User: an OTG Adapter is needed for
devices without standard USB.
5. How to solve the messy code problem encountered while
using other foreign languages?
The default language is English. Please refer to
“Language Setting” chapter to change the setting.
6. How to delete the extra charater in the prefix or suffix?
a. Scan code Prefix or Suffix Setting,
b. Scan code“1”“2”“7” sequentially, then scan code "Exit
with Save"
Note
If you receive an error of unable to transfer data via the
wireless connection (Not applicable for the Offline Mode),
please re-pair the scanner using the following steps. Please
bear in mind that this process may take 3-15 seconds.
Plug the 2.4G adapter
into your PC
Read “Enter Setup” Read “2.4G pairing”
For any inquiries or comments concerning our products, please
send an email to [email protected], and we will respond
to you as soon as possible.
www.inateck.com
5Common function Barcodes
Enter Setup Exit with Save
Exit without Save Factory Reset
Do not Apply Enter for suffix (*) Apply Enter for suffix
Apply Tab for suffix Exit Auto Power Off
Germany
Tel.: [phone] Fax.: [phone]
Phone hours: Weekdays 9 AM-5 PM (CET)
Email: [e-mail]
Web: http://www.inateck.com/de/
Addr.: F&M TECHNOLOGY GmbH, Montgolfierstraße 6,
04509 Wiedemar
Company of License Holder
Shenzhen Licheng Technology Co,.Ltd
Add: Warehouse B, 1F, Building B, Dezhong Industrial Park,
No.11 Shibei Road,
Bantian Street, Longgang District, Shenzhen, Guangdong,
518000, China Tel: [phone]
Manufacturer Information
Shenzhen Lixin Technology Co,.Ltd
Add: 1F, Building B , Dezhong Industrial Park, No.11 Shibei
Road, Bantian Street,
Longgang District, Shenzhen, Guangdong, 518000, China
Tel: [phone]
USA
Tel.: [phone]
Phone hours: Weekdays 9 AM to 5 PM (EST)
Email: [e-mail]
Web: www.inateck.com
Addr.: Inateck Technology Inc, 6045 Harrison Drive Suite 6，
Las Vegas, Nevada 89120
Contact Information
Enable Auto-induction Mode
2.4G pairing
2.4G pairing
Note:
1. If you want to setup the function of BCST-20. Read ‘Enter
Setup’ barcode, then ‘Function Setup’ barcode, and read ‘Exit
with Save’ at last.
2. Please remove the power and USB cable under thunderstorm
weather, to avoid damage from thunder and lightning.
3. Away heat source, keep ventilating.
4. Pay attention to waterproof during storage, transportation and
running.
LED lndicators
Indicator Colour Meaning
Blue LED on (1s) and off quickly
Green, Flashing (On/Off ratio 1:1)
Blue, Flashing (On/Off ratio 20ms:3s)
Red, Charging indicator
One short beep, high tone
One long beep, low tone
Two short beeps, high tone
Three short beeps, tone descending from high to low
Three short beeps, tone ascending from low to high
Read barcode, with blue LED on (1s) and off quickly
Configuration error, with purple flashing; Or transmit buffer full, with green LED
on and off quickly
Power off
Enter or Exit Setting mode, with green LED flashing
Configuration correct, with green LED flashing
Good Read, with one short beep (high tone)
Indicates the BCST-20 Scanner in Setting mode
Indicates the BCST-20 Scanner establish a wireless connection successfully
The red indicator will light during charging, and off when full charged.
Beeper
Beeping Meaning
Enter setup
6Function Setup Barcodes
(*) Enable Code bar
Enable Industral 25
(*) Enable Interleaved 25
Enable Matrix 25
(*) Enable Standard 25
Disable Interleaved 25
(*) Disable Industrial 25
Disable Code bar
(*) Disable Matrix 25
Disable Standard 25
(*) Enable Code 39 Disable Code 39
(*) Enable Code 93
Disable EAN-13
Disable EAN-8
Disable Code 128
(*) Enable Code 128
(*) Enable EAN-8
Disable Code 93
(*) Enable EAN-13
(*) Enable UPC-E Disable UPC-E
Enable MSI (*) Disable MSI
Exit with Save Enter Setup
(Note: the barcode with * is default setting of BCST-20)

7Features
1. Supports a wide range of barcode types. FedEx and USPS
barcodes are all supported.
2. Anti-crash and anti-shock design.
3. Ergonomic design.Up to 3 million keystroke life expectancy.
4. Unrivalled battery life.
5. Press to scan - powered by deep sleep mode.
6. USB mode: 64 bit barcodes. 2.4G wireless mode: 57 bit
barcodes.
7. Prefix and suffix are allowed to be added. Reset to factory
default settings by scanning the “Factory Reset” barcode.
9Support
8FAQ
1. Some barcodes cannot be read, why?
a. Dirty or unclear barcodes might not be read.
b. Digital barcodes displayed on phones, computers or
tablets cannot be read.
c. The possible reason is that the setting for some
barcode types are not commonly used is off by
default. You need to activate a specific barcode type
to get it to work. Please feel free to contact our
Customer Service Team for further assistance if you
don't know the exact type of barcode that you are
referring to.
2. Is there any barcodes for apply or remove Enter for
suffix?
Yes, you can refer to the Common Function Barcodes
to reverse the setting.
3. The data cannot be sent to my computer or cellphone.
Why?
Please make sure if you have turned on the offline
mode. Because it will store your scans internally
instead of instantly transmitting them to the connected
device. You need to scan the "Manual data upload"
barcode to send the scanned codes to your connected
device.
4. Is the device compatible with android devices?
Yes，For Android User: an OTG Adapter is needed for
devices without standard USB.
5. How to solve the messy code problem encountered while
using other foreign languages?
The default language is English. Please refer to
“Language Setting” chapter to change the setting.
6. How to delete the extra charater in the prefix or suffix?
a. Scan code Prefix or Suffix Setting,
b. Scan code“1”“2”“7” sequentially, then scan code "Exit
with Save"
Note
If you receive an error of unable to transfer data via the
wireless connection (Not applicable for the Offline Mode),
please re-pair the scanner using the following steps. Please
bear in mind that this process may take 3-15 seconds.
Plug the 2.4G adapter
into your PC
Read “Enter Setup” Read “2.4G pairing”
For any inquiries or comments concerning our products, please
send an email to [email protected], and we will respond
to you as soon as possible.
www.inateck.com
5Common function Barcodes
Enter Setup Exit with Save
Exit without Save Factory Reset
Do not Apply Enter for suffix (*) Apply Enter for suffix
Apply Tab for suffix Exit Auto Power Off
Germany
Tel.: [phone] Fax.: [phone]
Phone hours: Weekdays 9 AM-5 PM (CET)
Email: [e-mail]
Web: http://www.inateck.com/de/
Addr.: F&M TECHNOLOGY GmbH, Montgolfierstraße 6,
04509 Wiedemar
Company of License Holder
Shenzhen Licheng Technology Co,.Ltd
Add: Warehouse B, 1F, Building B, Dezhong Industrial Park,
No.11 Shibei Road,
Bantian Street, Longgang District, Shenzhen, Guangdong,
518000, China Tel: [phone]
Manufacturer Information
Shenzhen Lixin Technology Co,.Ltd
Add: 1F, Building B , Dezhong Industrial Park, No.11 Shibei
Road, Bantian Street,
Longgang District, Shenzhen, Guangdong, 518000, China
Tel: [phone]
USA
Tel.: [phone]
Phone hours: Weekdays 9 AM to 5 PM (EST)
Email: [e-mail]
Web: www.inateck.com
Addr.: Inateck Technology Inc, 6045 Harrison Drive Suite 6，
Las Vegas, Nevada 89120
Contact Information
Enable Auto-induction Mode
2.4G pairing
2.4G pairing
Note:
1. If you want to setup the function of BCST-20. Read ‘Enter
Setup’ barcode, then ‘Function Setup’ barcode, and read ‘Exit
with Save’ at last.
2. Please remove the power and USB cable under thunderstorm
weather, to avoid damage from thunder and lightning.
3. Away heat source, keep ventilating.
4. Pay attention to waterproof during storage, transportation and
running.
LED lndicators
Indicator Colour Meaning
Blue LED on (1s) and off quickly
Green, Flashing (On/Off ratio 1:1)
Blue, Flashing (On/Off ratio 20ms:3s)
Red, Charging indicator
One short beep, high tone
One long beep, low tone
Two short beeps, high tone
Three short beeps, tone descending from high to low
Three short beeps, tone ascending from low to high
Read barcode, with blue LED on (1s) and off quickly
Configuration error, with purple flashing; Or transmit buffer full, with green LED
on and off quickly
Power off
Enter or Exit Setting mode, with green LED flashing
Configuration correct, with green LED flashing
Good Read, with one short beep (high tone)
Indicates the BCST-20 Scanner in Setting mode
Indicates the BCST-20 Scanner establish a wireless connection successfully
The red indicator will light during charging, and off when full charged.
Beeper
Beeping Meaning
Enter setup
6Function Setup Barcodes
(*) Enable Code bar
Enable Industral 25
(*) Enable Interleaved 25
Enable Matrix 25
(*) Enable Standard 25
Disable Interleaved 25
(*) Disable Industrial 25
Disable Code bar
(*) Disable Matrix 25
Disable Standard 25
(*) Enable Code 39 Disable Code 39
(*) Enable Code 93
Disable EAN-13
Disable EAN-8
Disable Code 128
(*) Enable Code 128
(*) Enable EAN-8
Disable Code 93
(*) Enable EAN-13
(*) Enable UPC-E Disable UPC-E
Enable MSI (*) Disable MSI
Exit with Save Enter Setup
(Note: the barcode with * is default setting of BCST-20)

7Features
1. Supports a wide range of barcode types. FedEx and USPS
barcodes are all supported.
2. Anti-crash and anti-shock design.
3. Ergonomic design.Up to 3 million keystroke life expectancy.
4. Unrivalled battery life.
5. Press to scan - powered by deep sleep mode.
6. USB mode: 64 bit barcodes. 2.4G wireless mode: 57 bit
barcodes.
7. Prefix and suffix are allowed to be added. Reset to factory
default settings by scanning the “Factory Reset” barcode.
9Support
8FAQ
1. Some barcodes cannot be read, why?
a. Dirty or unclear barcodes might not be read.
b. Digital barcodes displayed on phones, computers or
tablets cannot be read.
c. The possible reason is that the setting for some
barcode types are not commonly used is off by
default. You need to activate a specific barcode type
to get it to work. Please feel free to contact our
Customer Service Team for further assistance if you
don't know the exact type of barcode that you are
referring to.
2. Is there any barcodes for apply or remove Enter for
suffix?
Yes, you can refer to the Common Function Barcodes
to reverse the setting.
3. The data cannot be sent to my computer or cellphone.
Why?
Please make sure if you have turned on the offline
mode. Because it will store your scans internally
instead of instantly transmitting them to the connected
device. You need to scan the "Manual data upload"
barcode to send the scanned codes to your connected
device.
4. Is the device compatible with android devices?
Yes，For Android User: an OTG Adapter is needed for
devices without standard USB.
5. How to solve the messy code problem encountered while
using other foreign languages?
The default language is English. Please refer to
“Language Setting” chapter to change the setting.
6. How to delete the extra charater in the prefix or suffix?
a. Scan code Prefix or Suffix Setting,
b. Scan code“1”“2”“7” sequentially, then scan code "Exit
with Save"
Note
If you receive an error of unable to transfer data via the
wireless connection (Not applicable for the Offline Mode),
please re-pair the scanner using the following steps. Please
bear in mind that this process may take 3-15 seconds.
Plug the 2.4G adapter
into your PC
Read “Enter Setup” Read “2.4G pairing”
For any inquiries or comments concerning our products, please
send an email to [email protected], and we will respond
to you as soon as possible.
www.inateck.com
5Common function Barcodes
Enter Setup Exit with Save
Exit without Save Factory Reset
Do not Apply Enter for suffix (*) Apply Enter for suffix
Apply Tab for suffix Exit Auto Power Off
Germany
Tel.: [phone] Fax.: [phone]
Phone hours: Weekdays 9 AM-5 PM (CET)
Email: [e-mail]
Web: http://www.inateck.com/de/
Addr.: F&M TECHNOLOGY GmbH, Montgolfierstraße 6,
04509 Wiedemar
Company of License Holder
Shenzhen Licheng Technology Co,.Ltd
Add: Warehouse B, 1F, Building B, Dezhong Industrial Park,
No.11 Shibei Road,
Bantian Street, Longgang District, Shenzhen, Guangdong,
518000, China Tel: [phone]
Manufacturer Information
Shenzhen Lixin Technology Co,.Ltd
Add: 1F, Building B , Dezhong Industrial Park, No.11 Shibei
Road, Bantian Street,
Longgang District, Shenzhen, Guangdong, 518000, China
Tel: [phone]
USA
Tel.: [phone]
Phone hours: Weekdays 9 AM to 5 PM (EST)
Email: [e-mail]
Web: www.inateck.com
Addr.: Inateck Technology Inc, 6045 Harrison Drive Suite 6，
Las Vegas, Nevada 89120
Contact Information
Enable Auto-induction Mode
2.4G pairing
2.4G pairing
Note:
1. If you want to setup the function of BCST-20. Read ‘Enter
Setup’ barcode, then ‘Function Setup’ barcode, and read ‘Exit
with Save’ at last.
2. Please remove the power and USB cable under thunderstorm
weather, to avoid damage from thunder and lightning.
3. Away heat source, keep ventilating.
4. Pay attention to waterproof during storage, transportation and
running.
LED lndicators
Indicator Colour Meaning
Blue LED on (1s) and off quickly
Green, Flashing (On/Off ratio 1:1)
Blue, Flashing (On/Off ratio 20ms:3s)
Red, Charging indicator
One short beep, high tone
One long beep, low tone
Two short beeps, high tone
Three short beeps, tone descending from high to low
Three short beeps, tone ascending from low to high
Read barcode, with blue LED on (1s) and off quickly
Configuration error, with purple flashing; Or transmit buffer full, with green LED
on and off quickly
Power off
Enter or Exit Setting mode, with green LED flashing
Configuration correct, with green LED flashing
Good Read, with one short beep (high tone)
Indicates the BCST-20 Scanner in Setting mode
Indicates the BCST-20 Scanner establish a wireless connection successfully
The red indicator will light during charging, and off when full charged.
Beeper
Beeping Meaning
Enter setup
6Function Setup Barcodes
(*) Enable Code bar
Enable Industral 25
(*) Enable Interleaved 25
Enable Matrix 25
(*) Enable Standard 25
Disable Interleaved 25
(*) Disable Industrial 25
Disable Code bar
(*) Disable Matrix 25
Disable Standard 25
(*) Enable Code 39 Disable Code 39
(*) Enable Code 93
Disable EAN-13
Disable EAN-8
Disable Code 128
(*) Enable Code 128
(*) Enable EAN-8
Disable Code 93
(*) Enable EAN-13
(*) Enable UPC-E Disable UPC-E
Enable MSI (*) Disable MSI
Exit with Save Enter Setup
(Note: the barcode with * is default setting of BCST-20)

7Features
1. Supports a wide range of barcode types. FedEx and USPS
barcodes are all supported.
2. Anti-crash and anti-shock design.
3. Ergonomic design.Up to 3 million keystroke life expectancy.
4. Unrivalled battery life.
5. Press to scan - powered by deep sleep mode.
6. USB mode: 64 bit barcodes. 2.4G wireless mode: 57 bit
barcodes.
7. Prefix and suffix are allowed to be added. Reset to factory
default settings by scanning the “Factory Reset” barcode.
9Support
8FAQ
1. Some barcodes cannot be read, why?
a. Dirty or unclear barcodes might not be read.
b. Digital barcodes displayed on phones, computers or
tablets cannot be read.
c. The possible reason is that the setting for some
barcode types are not commonly used is off by
default. You need to activate a specific barcode type
to get it to work. Please feel free to contact our
Customer Service Team for further assistance if you
don't know the exact type of barcode that you are
referring to.
2. Is there any barcodes for apply or remove Enter for
suffix?
Yes, you can refer to the Common Function Barcodes
to reverse the setting.
3. The data cannot be sent to my computer or cellphone.
Why?
Please make sure if you have turned on the offline
mode. Because it will store your scans internally
instead of instantly transmitting them to the connected
device. You need to scan the "Manual data upload"
barcode to send the scanned codes to your connected
device.
4. Is the device compatible with android devices?
Yes，For Android User: an OTG Adapter is needed for
devices without standard USB.
5. How to solve the messy code problem encountered while
using other foreign languages?
The default language is English. Please refer to
“Language Setting” chapter to change the setting.
6. How to delete the extra charater in the prefix or suffix?
a. Scan code Prefix or Suffix Setting,
b. Scan code“1”“2”“7” sequentially, then scan code "Exit
with Save"
Note
If you receive an error of unable to transfer data via the
wireless connection (Not applicable for the Offline Mode),
please re-pair the scanner using the following steps. Please
bear in mind that this process may take 3-15 seconds.
Plug the 2.4G adapter
into your PC
Read “Enter Setup” Read “2.4G pairing”
For any inquiries or comments concerning our products, please
send an email to [email protected], and we will respond
to you as soon as possible.
www.inateck.com
5Common function Barcodes
Enter Setup Exit with Save
Exit without Save Factory Reset
Do not Apply Enter for suffix (*) Apply Enter for suffix
Apply Tab for suffix Exit Auto Power Off
Germany
Tel.: [phone] Fax.: [phone]
Phone hours: Weekdays 9 AM-5 PM (CET)
Email: [e-mail]
Web: http://www.inateck.com/de/
Addr.: F&M TECHNOLOGY GmbH, Montgolfierstraße 6,
04509 Wiedemar
Company of License Holder
Shenzhen Licheng Technology Co,.Ltd
Add: Warehouse B, 1F, Building B, Dezhong Industrial Park,
No.11 Shibei Road,
Bantian Street, Longgang District, Shenzhen, Guangdong,
518000, China Tel: [phone]
Manufacturer Information
Shenzhen Lixin Technology Co,.Ltd
Add: 1F, Building B , Dezhong Industrial Park, No.11 Shibei
Road, Bantian Street,
Longgang District, Shenzhen, Guangdong, 518000, China
Tel: [phone]
USA
Tel.: [phone]
Phone hours: Weekdays 9 AM to 5 PM (EST)
Email: [e-mail]
Web: www.inateck.com
Addr.: Inateck Technology Inc, 6045 Harrison Drive Suite 6，
Las Vegas, Nevada 89120
Contact Information
Enable Auto-induction Mode
2.4G pairing
2.4G pairing
Note:
1. If you want to setup the function of BCST-20. Read ‘Enter
Setup’ barcode, then ‘Function Setup’ barcode, and read ‘Exit
with Save’ at last.
2. Please remove the power and USB cable under thunderstorm
weather, to avoid damage from thunder and lightning.
3. Away heat source, keep ventilating.
4. Pay attention to waterproof during storage, transportation and
running.
LED lndicators
Indicator Colour Meaning
Blue LED on (1s) and off quickly
Green, Flashing (On/Off ratio 1:1)
Blue, Flashing (On/Off ratio 20ms:3s)
Red, Charging indicator
One short beep, high tone
One long beep, low tone
Two short beeps, high tone
Three short beeps, tone descending from high to low
Three short beeps, tone ascending from low to high
Read barcode, with blue LED on (1s) and off quickly
Configuration error, with purple flashing; Or transmit buffer full, with green LED
on and off quickly
Power off
Enter or Exit Setting mode, with green LED flashing
Configuration correct, with green LED flashing
Good Read, with one short beep (high tone)
Indicates the BCST-20 Scanner in Setting mode
Indicates the BCST-20 Scanner establish a wireless connection successfully
The red indicator will light during charging, and off when full charged.
Beeper
Beeping Meaning
Enter setup
6Function Setup Barcodes
(*) Enable Code bar
Enable Industral 25
(*) Enable Interleaved 25
Enable Matrix 25
(*) Enable Standard 25
Disable Interleaved 25
(*) Disable Industrial 25
Disable Code bar
(*) Disable Matrix 25
Disable Standard 25
(*) Enable Code 39 Disable Code 39
(*) Enable Code 93
Disable EAN-13
Disable EAN-8
Disable Code 128
(*) Enable Code 128
(*) Enable EAN-8
Disable Code 93
(*) Enable EAN-13
(*) Enable UPC-E Disable UPC-E
Enable MSI (*) Disable MSI
Exit with Save Enter Setup
(Note: the barcode with * is default setting of BCST-20)

7Features
1. Supports a wide range of barcode types. FedEx and USPS
barcodes are all supported.
2. Anti-crash and anti-shock design.
3. Ergonomic design.Up to 3 million keystroke life expectancy.
4. Unrivalled battery life.
5. Press to scan - powered by deep sleep mode.
6. USB mode: 64 bit barcodes. 2.4G wireless mode: 57 bit
barcodes.
7. Prefix and suffix are allowed to be added. Reset to factory
default settings by scanning the “Factory Reset” barcode.
9Support
8FAQ
1. Some barcodes cannot be read, why?
a. Dirty or unclear barcodes might not be read.
b. Digital barcodes displayed on phones, computers or
tablets cannot be read.
c. The possible reason is that the setting for some
barcode types are not commonly used is off by
default. You need to activate a specific barcode type
to get it to work. Please feel free to contact our
Customer Service Team for further assistance if you
don't know the exact type of barcode that you are
referring to.
2. Is there any barcodes for apply or remove Enter for
suffix?
Yes, you can refer to the Common Function Barcodes
to reverse the setting.
3. The data cannot be sent to my computer or cellphone.
Why?
Please make sure if you have turned on the offline
mode. Because it will store your scans internally
instead of instantly transmitting them to the connected
device. You need to scan the "Manual data upload"
barcode to send the scanned codes to your connected
device.
4. Is the device compatible with android devices?
Yes，For Android User: an OTG Adapter is needed for
devices without standard USB.
5. How to solve the messy code problem encountered while
using other foreign languages?
The default language is English. Please refer to
“Language Setting” chapter to change the setting.
6. How to delete the extra charater in the prefix or suffix?
a. Scan code Prefix or Suffix Setting,
b. Scan code“1”“2”“7” sequentially, then scan code "Exit
with Save"
Note
If you receive an error of unable to transfer data via the
wireless connection (Not applicable for the Offline Mode),
please re-pair the scanner using the following steps. Please
bear in mind that this process may take 3-15 seconds.
Plug the 2.4G adapter
into your PC
Read “Enter Setup” Read “2.4G pairing”
For any inquiries or comments concerning our products, please
send an email to [email protected], and we will respond
to you as soon as possible.
www.inateck.com
5Common function Barcodes
Enter Setup Exit with Save
Exit without Save Factory Reset
Do not Apply Enter for suffix (*) Apply Enter for suffix
Apply Tab for suffix Exit Auto Power Off
Germany
Tel.: [phone] Fax.: [phone]
Phone hours: Weekdays 9 AM-5 PM (CET)
Email: [e-mail]
Web: http://www.inateck.com/de/
Addr.: F&M TECHNOLOGY GmbH, Montgolfierstraße 6,
04509 Wiedemar
Company of License Holder
Shenzhen Licheng Technology Co,.Ltd
Add: Warehouse B, 1F, Building B, Dezhong Industrial Park,
No.11 Shibei Road,
Bantian Street, Longgang District, Shenzhen, Guangdong,
518000, China Tel: [phone]
Manufacturer Information
Shenzhen Lixin Technology Co,.Ltd
Add: 1F, Building B , Dezhong Industrial Park, No.11 Shibei
Road, Bantian Street,
Longgang District, Shenzhen, Guangdong, 518000, China
Tel: [phone]
USA
Tel.: [phone]
Phone hours: Weekdays 9 AM to 5 PM (EST)
Email: [e-mail]
Web: www.inateck.com
Addr.: Inateck Technology Inc, 6045 Harrison Drive Suite 6，
Las Vegas, Nevada 89120
Contact Information
Enable Auto-induction Mode
2.4G pairing
2.4G pairing
Note:
1. If you want to setup the function of BCST-20. Read ‘Enter
Setup’ barcode, then ‘Function Setup’ barcode, and read ‘Exit
with Save’ at last.
2. Please remove the power and USB cable under thunderstorm
weather, to avoid damage from thunder and lightning.
3. Away heat source, keep ventilating.
4. Pay attention to waterproof during storage, transportation and
running.
LED lndicators
Indicator Colour Meaning
Blue LED on (1s) and off quickly
Green, Flashing (On/Off ratio 1:1)
Blue, Flashing (On/Off ratio 20ms:3s)
Red, Charging indicator
One short beep, high tone
One long beep, low tone
Two short beeps, high tone
Three short beeps, tone descending from high to low
Three short beeps, tone ascending from low to high
Read barcode, with blue LED on (1s) and off quickly
Configuration error, with purple flashing; Or transmit buffer full, with green LED
on and off quickly
Power off
Enter or Exit Setting mode, with green LED flashing
Configuration correct, with green LED flashing
Good Read, with one short beep (high tone)
Indicates the BCST-20 Scanner in Setting mode
Indicates the BCST-20 Scanner establish a wireless connection successfully
The red indicator will light during charging, and off when full charged.
Beeper
Beeping Meaning
Enter setup
6Function Setup Barcodes
(*) Enable Code bar
Enable Industral 25
(*) Enable Interleaved 25
Enable Matrix 25
(*) Enable Standard 25
Disable Interleaved 25
(*) Disable Industrial 25
Disable Code bar
(*) Disable Matrix 25
Disable Standard 25
(*) Enable Code 39 Disable Code 39
(*) Enable Code 93
Disable EAN-13
Disable EAN-8
Disable Code 128
(*) Enable Code 128
(*) Enable EAN-8
Disable Code 93
(*) Enable EAN-13
(*) Enable UPC-E Disable UPC-E
Enable MSI (*) Disable MSI
Exit with Save Enter Setup
(Note: the barcode with * is default setting of BCST-20)

7Features
1. Supports a wide range of barcode types. FedEx and USPS
barcodes are all supported.
2. Anti-crash and anti-shock design.
3. Ergonomic design.Up to 3 million keystroke life expectancy.
4. Unrivalled battery life.
5. Press to scan - powered by deep sleep mode.
6. USB mode: 64 bit barcodes. 2.4G wireless mode: 57 bit
barcodes.
7. Prefix and suffix are allowed to be added. Reset to factory
default settings by scanning the “Factory Reset” barcode.
9Support
8FAQ
1. Some barcodes cannot be read, why?
a. Dirty or unclear barcodes might not be read.
b. Digital barcodes displayed on phones, computers or
tablets cannot be read.
c. The possible reason is that the setting for some
barcode types are not commonly used is off by
default. You need to activate a specific barcode type
to get it to work. Please feel free to contact our
Customer Service Team for further assistance if you
don't know the exact type of barcode that you are
referring to.
2. Is there any barcodes for apply or remove Enter for
suffix?
Yes, you can refer to the Common Function Barcodes
to reverse the setting.
3. The data cannot be sent to my computer or cellphone.
Why?
Please make sure if you have turned on the offline
mode. Because it will store your scans internally
instead of instantly transmitting them to the connected
device. You need to scan the "Manual data upload"
barcode to send the scanned codes to your connected
device.
4. Is the device compatible with android devices?
Yes，For Android User: an OTG Adapter is needed for
devices without standard USB.
5. How to solve the messy code problem encountered while
using other foreign languages?
The default language is English. Please refer to
“Language Setting” chapter to change the setting.
6. How to delete the extra charater in the prefix or suffix?
a. Scan code Prefix or Suffix Setting,
b. Scan code“1”“2”“7” sequentially, then scan code "Exit
with Save"
Note
If you receive an error of unable to transfer data via the
wireless connection (Not applicable for the Offline Mode),
please re-pair the scanner using the following steps. Please
bear in mind that this process may take 3-15 seconds.
Plug the 2.4G adapter
into your PC
Read “Enter Setup” Read “2.4G pairing”
For any inquiries or comments concerning our products, please
send an email to [email protected], and we will respond
to you as soon as possible.
www.inateck.com
5Common function Barcodes
Enter Setup Exit with Save
Exit without Save Factory Reset
Do not Apply Enter for suffix (*) Apply Enter for suffix
Apply Tab for suffix Exit Auto Power Off
Germany
Tel.: [phone] Fax.: [phone]
Phone hours: Weekdays 9 AM-5 PM (CET)
Email: [e-mail]
Web: http://www.inateck.com/de/
Addr.: F&M TECHNOLOGY GmbH, Montgolfierstraße 6,
04509 Wiedemar
Company of License Holder
Shenzhen Licheng Technology Co,.Ltd
Add: Warehouse B, 1F, Building B, Dezhong Industrial Park,
No.11 Shibei Road,
Bantian Street, Longgang District, Shenzhen, Guangdong,
518000, China Tel: [phone]
Manufacturer Information
Shenzhen Lixin Technology Co,.Ltd
Add: 1F, Building B , Dezhong Industrial Park, No.11 Shibei
Road, Bantian Street,
Longgang District, Shenzhen, Guangdong, 518000, China
Tel: [phone]
USA
Tel.: [phone]
Phone hours: Weekdays 9 AM to 5 PM (EST)
Email: [e-mail]
Web: www.inateck.com
Addr.: Inateck Technology Inc, 6045 Harrison Drive Suite 6，
Las Vegas, Nevada 89120
Contact Information
Enable Auto-induction Mode
2.4G pairing
2.4G pairing
Note:
1. If you want to setup the function of BCST-20. Read ‘Enter
Setup’ barcode, then ‘Function Setup’ barcode, and read ‘Exit
with Save’ at last.
2. Please remove the power and USB cable under thunderstorm
weather, to avoid damage from thunder and lightning.
3. Away heat source, keep ventilating.
4. Pay attention to waterproof during storage, transportation and
running.
LED lndicators
Indicator Colour Meaning
Blue LED on (1s) and off quickly
Green, Flashing (On/Off ratio 1:1)
Blue, Flashing (On/Off ratio 20ms:3s)
Red, Charging indicator
One short beep, high tone
One long beep, low tone
Two short beeps, high tone
Three short beeps, tone descending from high to low
Three short beeps, tone ascending from low to high
Read barcode, with blue LED on (1s) and off quickly
Configuration error, with purple flashing; Or transmit buffer full, with green LED
on and off quickly
Power off
Enter or Exit Setting mode, with green LED flashing
Configuration correct, with green LED flashing
Good Read, with one short beep (high tone)
Indicates the BCST-20 Scanner in Setting mode
Indicates the BCST-20 Scanner establish a wireless connection successfully
The red indicator will light during charging, and off when full charged.
Beeper
Beeping Meaning
Enter setup
6Function Setup Barcodes
(*) Enable Code bar
Enable Industral 25
(*) Enable Interleaved 25
Enable Matrix 25
(*) Enable Standard 25
Disable Interleaved 25
(*) Disable Industrial 25
Disable Code bar
(*) Disable Matrix 25
Disable Standard 25
(*) Enable Code 39 Disable Code 39
(*) Enable Code 93
Disable EAN-13
Disable EAN-8
Disable Code 128
(*) Enable Code 128
(*) Enable EAN-8
Disable Code 93
(*) Enable EAN-13
(*) Enable UPC-E Disable UPC-E
Enable MSI (*) Disable MSI
Exit with Save Enter Setup
(Note: the barcode with * is default setting of BCST-20)

7Features
1. Supports a wide range of barcode types. FedEx and USPS
barcodes are all supported.
2. Anti-crash and anti-shock design.
3. Ergonomic design.Up to 3 million keystroke life expectancy.
4. Unrivalled battery life.
5. Press to scan - powered by deep sleep mode.
6. USB mode: 64 bit barcodes. 2.4G wireless mode: 57 bit
barcodes.
7. Prefix and suffix are allowed to be added. Reset to factory
default settings by scanning the “Factory Reset” barcode.
9Support
8FAQ
1. Some barcodes cannot be read, why?
a. Dirty or unclear barcodes might not be read.
b. Digital barcodes displayed on phones, computers or
tablets cannot be read.
c. The possible reason is that the setting for some
barcode types are not commonly used is off by
default. You need to activate a specific barcode type
to get it to work. Please feel free to contact our
Customer Service Team for further assistance if you
don't know the exact type of barcode that you are
referring to.
2. Is there any barcodes for apply or remove Enter for
suffix?
Yes, you can refer to the Common Function Barcodes
to reverse the setting.
3. The data cannot be sent to my computer or cellphone.
Why?
Please make sure if you have turned on the offline
mode. Because it will store your scans internally
instead of instantly transmitting them to the connected
device. You need to scan the "Manual data upload"
barcode to send the scanned codes to your connected
device.
4. Is the device compatible with android devices?
Yes，For Android User: an OTG Adapter is needed for
devices without standard USB.
5. How to solve the messy code problem encountered while
using other foreign languages?
The default language is English. Please refer to
“Language Setting” chapter to change the setting.
6. How to delete the extra charater in the prefix or suffix?
a. Scan code Prefix or Suffix Setting,
b. Scan code“1”“2”“7” sequentially, then scan code "Exit
with Save"
Note
If you receive an error of unable to transfer data via the
wireless connection (Not applicable for the Offline Mode),
please re-pair the scanner using the following steps. Please
bear in mind that this process may take 3-15 seconds.
Plug the 2.4G adapter
into your PC
Read “Enter Setup” Read “2.4G pairing”
For any inquiries or comments concerning our products, please
send an email to [email protected], and we will respond
to you as soon as possible.
www.inateck.com
5Common function Barcodes
Enter Setup Exit with Save
Exit without Save Factory Reset
Do not Apply Enter for suffix (*) Apply Enter for suffix
Apply Tab for suffix Exit Auto Power Off
Germany
Tel.: [phone] Fax.: [phone]
Phone hours: Weekdays 9 AM-5 PM (CET)
Email: [e-mail]
Web: http://www.inateck.com/de/
Addr.: F&M TECHNOLOGY GmbH, Montgolfierstraße 6,
04509 Wiedemar
Company of License Holder
Shenzhen Licheng Technology Co,.Ltd
Add: Warehouse B, 1F, Building B, Dezhong Industrial Park,
No.11 Shibei Road,
Bantian Street, Longgang District, Shenzhen, Guangdong,
518000, China Tel: [phone]
Manufacturer Information
Shenzhen Lixin Technology Co,.Ltd
Add: 1F, Building B , Dezhong Industrial Park, No.11 Shibei
Road, Bantian Street,
Longgang District, Shenzhen, Guangdong, 518000, China
Tel: [phone]
USA
Tel.: [phone]
Phone hours: Weekdays 9 AM to 5 PM (EST)
Email: [e-mail]
Web: www.inateck.com
Addr.: Inateck Technology Inc, 6045 Harrison Drive Suite 6，
Las Vegas, Nevada 89120
Contact Information
Enable Auto-induction Mode
2.4G pairing
2.4G pairing
Note:
1. If you want to setup the function of BCST-20. Read ‘Enter
Setup’ barcode, then ‘Function Setup’ barcode, and read ‘Exit
with Save’ at last.
2. Please remove the power and USB cable under thunderstorm
weather, to avoid damage from thunder and lightning.
3. Away heat source, keep ventilating.
4. Pay attention to waterproof during storage, transportation and
running.
LED lndicators
Indicator Colour Meaning
Blue LED on (1s) and off quickly
Green, Flashing (On/Off ratio 1:1)
Blue, Flashing (On/Off ratio 20ms:3s)
Red, Charging indicator
One short beep, high tone
One long beep, low tone
Two short beeps, high tone
Three short beeps, tone descending from high to low
Three short beeps, tone ascending from low to high
Read barcode, with blue LED on (1s) and off quickly
Configuration error, with purple flashing; Or transmit buffer full, with green LED
on and off quickly
Power off
Enter or Exit Setting mode, with green LED flashing
Configuration correct, with green LED flashing
Good Read, with one short beep (high tone)
Indicates the BCST-20 Scanner in Setting mode
Indicates the BCST-20 Scanner establish a wireless connection successfully
The red indicator will light during charging, and off when full charged.
Beeper
Beeping Meaning
Enter setup
6Function Setup Barcodes
(*) Enable Code bar
Enable Industral 25
(*) Enable Interleaved 25
Enable Matrix 25
(*) Enable Standard 25
Disable Interleaved 25
(*) Disable Industrial 25
Disable Code bar
(*) Disable Matrix 25
Disable Standard 25
(*) Enable Code 39 Disable Code 39
(*) Enable Code 93
Disable EAN-13
Disable EAN-8
Disable Code 128
(*) Enable Code 128
(*) Enable EAN-8
Disable Code 93
(*) Enable EAN-13
(*) Enable UPC-E Disable UPC-E
Enable MSI (*) Disable MSI
Exit with Save Enter Setup
(Note: the barcode with * is default setting of BCST-20)

7Features
1. Supports a wide range of barcode types. FedEx and USPS
barcodes are all supported.
2. Anti-crash and anti-shock design.
3. Ergonomic design.Up to 3 million keystroke life expectancy.
4. Unrivalled battery life.
5. Press to scan - powered by deep sleep mode.
6. USB mode: 64 bit barcodes. 2.4G wireless mode: 57 bit
barcodes.
7. Prefix and suffix are allowed to be added. Reset to factory
default settings by scanning the “Factory Reset” barcode.
9Support
8FAQ
1. Some barcodes cannot be read, why?
a. Dirty or unclear barcodes might not be read.
b. Digital barcodes displayed on phones, computers or
tablets cannot be read.
c. The possible reason is that the setting for some
barcode types are not commonly used is off by
default. You need to activate a specific barcode type
to get it to work. Please feel free to contact our
Customer Service Team for further assistance if you
don't know the exact type of barcode that you are
referring to.
2. Is there any barcodes for apply or remove Enter for
suffix?
Yes, you can refer to the Common Function Barcodes
to reverse the setting.
3. The data cannot be sent to my computer or cellphone.
Why?
Please make sure if you have turned on the offline
mode. Because it will store your scans internally
instead of instantly transmitting them to the connected
device. You need to scan the "Manual data upload"
barcode to send the scanned codes to your connected
device.
4. Is the device compatible with android devices?
Yes，For Android User: an OTG Adapter is needed for
devices without standard USB.
5. How to solve the messy code problem encountered while
using other foreign languages?
The default language is English. Please refer to
“Language Setting” chapter to change the setting.
6. How to delete the extra charater in the prefix or suffix?
a. Scan code Prefix or Suffix Setting,
b. Scan code“1”“2”“7” sequentially, then scan code "Exit
with Save"
Note
If you receive an error of unable to transfer data via the
wireless connection (Not applicable for the Offline Mode),
please re-pair the scanner using the following steps. Please
bear in mind that this process may take 3-15 seconds.
Plug the 2.4G adapter
into your PC
Read “Enter Setup” Read “2.4G pairing”
For any inquiries or comments concerning our products, please
send an email to [email protected], and we will respond
to you as soon as possible.
www.inateck.com
5Common function Barcodes
Enter Setup Exit with Save
Exit without Save Factory Reset
Do not Apply Enter for suffix (*) Apply Enter for suffix
Apply Tab for suffix Exit Auto Power Off
Germany
Tel.: [phone] Fax.: [phone]
Phone hours: Weekdays 9 AM-5 PM (CET)
Email: [e-mail]
Web: http://www.inateck.com/de/
Addr.: F&M TECHNOLOGY GmbH, Montgolfierstraße 6,
04509 Wiedemar
Company of License Holder
Shenzhen Licheng Technology Co,.Ltd
Add: Warehouse B, 1F, Building B, Dezhong Industrial Park,
No.11 Shibei Road,
Bantian Street, Longgang District, Shenzhen, Guangdong,
518000, China Tel: [phone]
Manufacturer Information
Shenzhen Lixin Technology Co,.Ltd
Add: 1F, Building B , Dezhong Industrial Park, No.11 Shibei
Road, Bantian Street,
Longgang District, Shenzhen, Guangdong, 518000, China
Tel: [phone]
USA
Tel.: [phone]
Phone hours: Weekdays 9 AM to 5 PM (EST)
Email: [e-mail]
Web: www.inateck.com
Addr.: Inateck Technology Inc, 6045 Harrison Drive Suite 6，
Las Vegas, Nevada 89120
Contact Information
Enable Auto-induction Mode
2.4G pairing
2.4G pairing
Note:
1. If you want to setup the function of BCST-20. Read ‘Enter
Setup’ barcode, then ‘Function Setup’ barcode, and read ‘Exit
with Save’ at last.
2. Please remove the power and USB cable under thunderstorm
weather, to avoid damage from thunder and lightning.
3. Away heat source, keep ventilating.
4. Pay attention to waterproof during storage, transportation and
running.
LED lndicators
Indicator Colour Meaning
Blue LED on (1s) and off quickly
Green, Flashing (On/Off ratio 1:1)
Blue, Flashing (On/Off ratio 20ms:3s)
Red, Charging indicator
One short beep, high tone
One long beep, low tone
Two short beeps, high tone
Three short beeps, tone descending from high to low
Three short beeps, tone ascending from low to high
Read barcode, with blue LED on (1s) and off quickly
Configuration error, with purple flashing; Or transmit buffer full, with green LED
on and off quickly
Power off
Enter or Exit Setting mode, with green LED flashing
Configuration correct, with green LED flashing
Good Read, with one short beep (high tone)
Indicates the BCST-20 Scanner in Setting mode
Indicates the BCST-20 Scanner establish a wireless connection successfully
The red indicator will light during charging, and off when full charged.
Beeper
Beeping Meaning
Enter setup
6Function Setup Barcodes
(*) Enable Code bar
Enable Industral 25
(*) Enable Interleaved 25
Enable Matrix 25
(*) Enable Standard 25
Disable Interleaved 25
(*) Disable Industrial 25
Disable Code bar
(*) Disable Matrix 25
Disable Standard 25
(*) Enable Code 39 Disable Code 39
(*) Enable Code 93
Disable EAN-13
Disable EAN-8
Disable Code 128
(*) Enable Code 128
(*) Enable EAN-8
Disable Code 93
(*) Enable EAN-13
(*) Enable UPC-E Disable UPC-E
Enable MSI (*) Disable MSI
Exit with Save Enter Setup
(Note: the barcode with * is default setting of BCST-20)

7Features
1. Supports a wide range of barcode types. FedEx and USPS
barcodes are all supported.
2. Anti-crash and anti-shock design.
3. Ergonomic design.Up to 3 million keystroke life expectancy.
4. Unrivalled battery life.
5. Press to scan - powered by deep sleep mode.
6. USB mode: 64 bit barcodes. 2.4G wireless mode: 57 bit
barcodes.
7. Prefix and suffix are allowed to be added. Reset to factory
default settings by scanning the “Factory Reset” barcode.
9Support
8FAQ
1. Some barcodes cannot be read, why?
a. Dirty or unclear barcodes might not be read.
b. Digital barcodes displayed on phones, computers or
tablets cannot be read.
c. The possible reason is that the setting for some
barcode types are not commonly used is off by
default. You need to activate a specific barcode type
to get it to work. Please feel free to contact our
Customer Service Team for further assistance if you
don't know the exact type of barcode that you are
referring to.
2. Is there any barcodes for apply or remove Enter for
suffix?
Yes, you can refer to the Common Function Barcodes
to reverse the setting.
3. The data cannot be sent to my computer or cellphone.
Why?
Please make sure if you have turned on the offline
mode. Because it will store your scans internally
instead of instantly transmitting them to the connected
device. You need to scan the "Manual data upload"
barcode to send the scanned codes to your connected
device.
4. Is the device compatible with android devices?
Yes，For Android User: an OTG Adapter is needed for
devices without standard USB.
5. How to solve the messy code problem encountered while
using other foreign languages?
The default language is English. Please refer to
“Language Setting” chapter to change the setting.
6. How to delete the extra charater in the prefix or suffix?
a. Scan code Prefix or Suffix Setting,
b. Scan code“1”“2”“7” sequentially, then scan code "Exit
with Save"
Note
If you receive an error of unable to transfer data via the
wireless connection (Not applicable for the Offline Mode),
please re-pair the scanner using the following steps. Please
bear in mind that this process may take 3-15 seconds.
Plug the 2.4G adapter
into your PC
Read “Enter Setup” Read “2.4G pairing”
For any inquiries or comments concerning our products, please
send an email to [email protected], and we will respond
to you as soon as possible.
www.inateck.com
5Common function Barcodes
Enter Setup Exit with Save
Exit without Save Factory Reset
Do not Apply Enter for suffix (*) Apply Enter for suffix
Apply Tab for suffix Exit Auto Power Off
Germany
Tel.: [phone] Fax.: [phone]
Phone hours: Weekdays 9 AM-5 PM (CET)
Email: [e-mail]
Web: http://www.inateck.com/de/
Addr.: F&M TECHNOLOGY GmbH, Montgolfierstraße 6,
04509 Wiedemar
Company of License Holder
Shenzhen Licheng Technology Co,.Ltd
Add: Warehouse B, 1F, Building B, Dezhong Industrial Park,
No.11 Shibei Road,
Bantian Street, Longgang District, Shenzhen, Guangdong,
518000, China Tel: [phone]
Manufacturer Information
Shenzhen Lixin Technology Co,.Ltd
Add: 1F, Building B , Dezhong Industrial Park, No.11 Shibei
Road, Bantian Street,
Longgang District, Shenzhen, Guangdong, 518000, China
Tel: [phone]
USA
Tel.: [phone]
Phone hours: Weekdays 9 AM to 5 PM (EST)
Email: [e-mail]
Web: www.inateck.com
Addr.: Inateck Technology Inc, 6045 Harrison Drive Suite 6，
Las Vegas, Nevada 89120
Contact Information
Enable Auto-induction Mode
2.4G pairing
2.4G pairing
Note:
1. If you want to setup the function of BCST-20. Read ‘Enter
Setup’ barcode, then ‘Function Setup’ barcode, and read ‘Exit
with Save’ at last.
2. Please remove the power and USB cable under thunderstorm
weather, to avoid damage from thunder and lightning.
3. Away heat source, keep ventilating.
4. Pay attention to waterproof during storage, transportation and
running.
LED lndicators
Indicator Colour Meaning
Blue LED on (1s) and off quickly
Green, Flashing (On/Off ratio 1:1)
Blue, Flashing (On/Off ratio 20ms:3s)
Red, Charging indicator
One short beep, high tone
One long beep, low tone
Two short beeps, high tone
Three short beeps, tone descending from high to low
Three short beeps, tone ascending from low to high
Read barcode, with blue LED on (1s) and off quickly
Configuration error, with purple flashing; Or transmit buffer full, with green LED
on and off quickly
Power off
Enter or Exit Setting mode, with green LED flashing
Configuration correct, with green LED flashing
Good Read, with one short beep (high tone)
Indicates the BCST-20 Scanner in Setting mode
Indicates the BCST-20 Scanner establish a wireless connection successfully
The red indicator will light during charging, and off when full charged.
Beeper
Beeping Meaning
Enter setup
6Function Setup Barcodes
(*) Enable Code bar
Enable Industral 25
(*) Enable Interleaved 25
Enable Matrix 25
(*) Enable Standard 25
Disable Interleaved 25
(*) Disable Industrial 25
Disable Code bar
(*) Disable Matrix 25
Disable Standard 25
(*) Enable Code 39 Disable Code 39
(*) Enable Code 93
Disable EAN-13
Disable EAN-8
Disable Code 128
(*) Enable Code 128
(*) Enable EAN-8
Disable Code 93
(*) Enable EAN-13
(*) Enable UPC-E Disable UPC-E
Enable MSI (*) Disable MSI
Exit with Save Enter Setup
(Note: the barcode with * is default setting of BCST-20)