Industrial Rivet & Fastener Co. Rivet King RK-7532-P3 User manual

Model# RK-7532-P3
Zero Gravity Pantograph
QuickRiveting® Tool

2
CONTENTS
Safety
Page 3
Specifications Page 3
Preparing the tool for service Page 4
Air supply Page 4
Maintenance
Daily Page 5
Weekly Page 5
Tail jaw cylinder Page 6
Hydraulic body Page 6
Intensifier Page 7
Pilot valve Page 7
Assembly Drawings & Components Page 8
Handle, Trigger & Nose Pages 9-11
Intensifier Pages 12-13
Linear Arm Page 14
Rotation Device Page 15
Troubleshooting Page 16
Warranty Page 17
MSDS Page 18-23

3
SAFETY
DO NOT USE EQUIPMENT WITH THIS TOOL THAT IS NOT RECOMMENDED OR SUPPLIED BY INDUSTRIAL RIVET &FASTENER CO.
ALWAYS DISCONNECT THE AIR SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE OR ADJUSTMENT/FITTING OF NOSE EQUIPMENT
DO NOT OPERATE A TOOL THAT IS DIRECTED TOWARDS ANY PERSON(S)
ALL MODIFICATIONS CARRIED OUT ON THE TOOL WITHOUT THE CONSENT OF INDUSTRIAL RIVET &FASTENER CO.SHALL BE
DONE SO AT THE CUSTOMERS’SOLE RESPONSIBILITY
REFER TO THIS MANUAL BEFORE ATTEMPTING ANY MAINTENANCE OPERATION
AVOID EXCESSIVE CONTACT WITH HYDRAULIC OIL (Velocite No 10),AS SOON AS POSSIBLE WASH HANDS THOROUGHLY
DO NOT EXCEED 7BAR /100 PSI INLET PRESSURE,THE USE OF A PRESSURE REGULATOR IS HIGHLY RECOMMENDED
INSPECT THE MANDREL REGULARLY.WHILE SOME MARKING THROUGH USE IS NORMAL EXCESSIVE PITTING AND DISTORTION
MAY CAUSE A MANDREL TO FAIL.AMANDREL THAT FAILS MAY FORCIBLY EJECT FROM THE TOOL.MANDRELS SHOULD BE
INSPECTED BEFORE THE RECOMMENDED NUMBER OF PLACINGS BASED UPON THE BROACH LOAD OF THE PARTICULAR
APPLICATION.IF YOU ARE UNSURE OF THE BROACH LOAD CONATCT YOUR INDUSTRIAL RIVET &FASTENER CO.REPRESENTATIVE
WHO WILL HELP YOU DETERMINE WHAT THIS IS AND THE SAFE NUMBER OF PLACINGS TO EXPECT FROM THE MANDREL
SPECIFICATIONS
The specifications and information contained in this manual are applicable only to the tool with which it was
supplied. Industrial Rivet & Fastener Co reserve the right to make any changes without notice as part of
Industrial Rivet & Fastener Co policy of continuous improvement.
SPECIFICATIONS FOR RK-753™ INTENSIFIER /BOOSTER
Air Pressure Min/Max □5 – 7 bar □70 – 100 psi
Intensification Ratio □30 : 1 □
SPECIFICATIONS FOR RK-753™ RIVET TOOL
Air Pressure Min/Max □5 – 7 bar □70 – 100 psi
Free Air Volume Required @5.1 bar/75psi □2.6 liters □.09 ft
Stroke Minimum □30 mm □
Pull Force @5.5 bar/80psi □3.89kN □
Cycle Time Approximately □1-1.5 seconds □
Noise Level Less than □70 dB(A) □
Weight □1.2kg □2.64 lb
Vibration Less Than □2.5 m/s □8
ft/s

4
PREPARING THE TOOL FOR SERVICE
1
1
1.
.
.
Check to see if a cursor is present in the barrel, fit a cursor into the barrel (1) if not present
ensuring that the spring loaded plunger of the cursor is towards the front of the barrel
2
2
2.
.
.
Fit correct nose assembly for the rivet being placed
3
3
3.
.
.
Connect the hydraulic hose assembly from the tool to the intensifier
4
4
4.
.
.
Connect the trigger/tail jaw supply line into the quick release collet on the pilot valve bolted
to the intensifier
5
5
5.
.
.
Connect the main air supply to the rear of the intensifier
6
6
6.
.
.
Open the tail jaws (24) by switching off the sir supply through the trigger/tail jaw assembly
(38)
7
7
7.
.
.
Load rivets onto mandrel by inserting the mandrel through the tail of the rivets and remove
the paper strips
8
8
8.
.
.
Place follower spring onto the mandrel
9
9
9.
.
.
Open front jaw assembly and insert loaded mandrel through the nose assembly until a gap of
approximately 1.5mm (1/16”) – 3mm (1/8”) between the head of the first rivet and the nose
assembly is achieved
1
1
10
0
0.
.
.
Close tail jaws (24) to grip the mandrel, the tool is now loaded and ready for use
AIR SUPPLY
The rivet tool is powered by compressed air at an optimum pressure of 5.5 bar (80 psi)
The use of a pressure regulator filter/lubricator unit within 3 meters of the tool is highly
recommended to extend the life of the tool.
Dirt and/or water in the air supply can seriously impact the performance and durability of
the tool; damage to the tool caused by contaminated air supply is not covered under
warranty

5
MAINTENANCE
In order to maintain the tool in a safe working order it is important to carry out regular maintenance
as prescribed by the manufacturer. A thorough inspection replacement of all seals within the tool
should be carried out after 500,000 placings or annually, whichever is the sooner. Item numbers in
parentheses refer to assembly drawing part numbers
Daily
Check for air leaks, pay particular attention to the elbow connectors (21) supplying the tail
jaws. Any damaged hoses should be replaced
Lubricate the tool by pouring a few drops of light lubricating oil into the air inlet on the
intensifier
Inspect all mandrels for signs of wear or damage. Discard any mandrels that display signs of
excessive pitting or distortion
Remove front jaw nose assembly and inspect for cracks or other damage
Inspect and clean the cursor assembly, lubricate with light oil and replace with the spring
loaded end of the cursor toward the threaded end of the barrel. If the cursor is inserted the
wrong way round, the tool will not feed rivets. Carry out the following steps to reorient the
cursor
oLoosen screws (35) and remove end cover (20)
oRemove screw (18) seals (19) and cover (17) note there are two seals one either side
of the cover
oRemove circlip (15) rear plug (16) turret assembly (22) with jaws (24) spring (23)
and jaw housing (25)
oInsert a mandrel through the barrel nut (13) holding onto the bulb end and feed the
mandrel up and through the barrel. The mandrel will pull the cursor out of the barrel
to be inserted correctly.
Weekly
Carry out procedures as per daily maintenance instructions above
Clean and inspect the tail jaws for signs of damage or wear (groove running through the jaw
serrations). Follow the instructions above to re-orient the cursor to access the tail jaws in the
tail jaw cylinder. Reassemble the tail jaws with a light coating of grease on the outer face
that contacts the jaw housing. Do not allow grease to contaminate the grooved inner face of
the jaws as mandrel slippage may result.
Check the oil level in the reservoir, the oil should be approximately ½” below the plexiglass
cover plate fitted to the intensifier. If the tool requires topping up with oil on a regular basis
check for leaking seals or damaged hoses and couplings

6
MAINTENANCE
Follow the instructions below to perform annual service and replacement of seals, item numbers in
parentheses refer to assembly drawing part numbers on page 8.
Tail Jaw Cylinder
Disconnect tool from air supply
Disconnect rivet tool and hose assembly from intensifier
Loosen screws (35) and remove end cover (20)
Remove handle covers by removing (31,32) by removing retaining screws (33, 34)
Disconnect tail jaw supply tube from elbow connector or using a small flat screwdriver
remove the elbow connector complete taking care to retain the seals
Remove screw (18) seals (19) and cover (17) note there are two seals one either side of the
cover
Remove circlip (15) rear plug (16) turret assembly (22) with jaws (24) spring (23) and jaw
housing (25). Inspect all parts for signs of wear or damage and replace if necessary
Using an 18mm A/F open ended wrench on the flats machined onto the barrel (1) and a
13mm A/F socket wrench, remove the barrel plug (13)
Carefully slide tail jaw cylinder (10) with return spring (11) off the barrel. Clean and inspect
tail jaw cylinder and spring for signs of wear/damage
Replace all O ring seals and lubricate with a light coating of grease including the jaws as
described in the weekly maintenance instructions
Reassemble in reverse order
Hydraulic Body
Carry out instructions above to dismantle the tail jaw cylinder
Disconnect trigger supply line to the trigger assembly (38). Loosen screw securing the trigger
assembly in position on the barrel and slide toward the front end of the barrel and set aside
Remove the bleed plug assembly and seal (5, 6) a small amount of hydraulic fluid will run out
of the tool and care should be taken to avoid excessive contact with skin and should be
disposed of safely
Unscrew the hydraulic hose and set aside over a suitable container to catch any fluid that
may leak out
Grip stroke limiter (9) in a vise across the flats machined and using a 32mm A/F wrench
unscrew hydraulic body (8) from stroke limiter and remove piston (28)
Pry out seals (2, 7) taking care not to damage internal bore of hydraulic body
Clean all parts and check for signs of wear/damage, replace all seals lubricating with a light
coating of grease and reassemble in reverse order.
Tip: When inserting the barrel through the hydraulic piston and stroke limiter assembly place
the tail jaw cylinder against the back of the piston (28) in order to help keep the dynamic
seal in the correct orientation. If this is not done the seal can become dislodged and the tool
will leak requiring another strip down!

7
MAINTENANCE
Follow the instructions below to perform annual service and replacement of seals, item numbers in
parentheses refer to assembly drawing part numbers on page 9.
Intensifier Unit
Disconnect tool from air supply
Disconnect rivet tool and hose assembly from intensifier
Remove hydraulic coupler (1) and seals (2) holding unit over a suitable container to collect
the hydraulic fluid
Remove screw (18) together with cover plate (17), spacer (19) plate (16) and silencer (30)
Using a flat bladed screwdriver pry out and remove spiral retaining ring (15)
Screw item 18 back into end cap (20) and pull out the end cap (20), cylinder liner (10) and
piston assembly (22).
Using an intensifier spanner/wrench as detailed on page 10, unscrew and remove the seal
plug (23)
Carefully remove all seals (24, 28, 28), spacers (25, 29) and seal housing (27)
Remove cover plate (7) and gasket (6) by removing the four retaining screws (32) and
washers (33)
Using the other end of the intensifier spanner/wrench remove the valve assembly (5)
Clean and inspect all parts for signs of wear or damage
Replace all O ring seals
Reassemble in reverse order lubricating all seals with a light coating of grease
Pilot valve
Disconnect tool from air supply
Remove pilot valve from base of intensifier by removing three retaining screws being careful
to retain sealing rings
Unscrew and remove end caps
Remove pistons and valve spool, O rings & spacers, clean all items and check for damage
Reassemble pistons with a light coating of grease.
Lightly coat the spool with a small amount of light oil, wipe with a clean rag and replace into
valve assembly
If necessary; replace all o rings available as a service kit part number RK101-00010
Reassemble in reverse order

8
General Assembly & Components of RK7532
1) Handle and Trigger Assembly
2) Intensifier Assembly
3) Linear Arm Assembly
4) Rotation Device Assembly

9
RK7532-P3 Pantograph Handle/Hose Assembly

10
RK7532-P3 Pantograph Handle/Hose Assembly
Parts List
# Part# Description Qty
4 TP-RK7532-H004UY REAR PLUGE 1
5 TP-RK7532-H005Y TAIL JAW TUBE 1
6 NOT INCLUDED NOT INCLUDED
7 TP-RK7532-H007Y SPRING 1
8 TP-RK7532-H008Y TAIL JAW PISTON ASS'Y 1
8 TP-RK7532-H008-1 TAIL JAW PISTON 1
8 TP-RK7532-H008-2 TURRET PLUG 1
9 TP-RK7532-H009N RUBBING STRIP 1
10 TP-RK7532-H010N STROKE LIMITER 1
11 TP-RK7532-H011Y PISTON 1
12 TP-RK7532-H012N BODY 1
13 TP-RK7532-H013Y SEAL 3
14 TP-RK7532-H014Y 4MM AIR HOSE(2500MM) 1
15 TP-RK7532-H015Y CABLE TIES (4"BLACK) 9
16 TP-RK7532-H016Y HYDRAULIC HOSE ASS'Y 1
17 TP-RK7532-H017N HANDLE MOULDING(RIGHT) 1
18 TP-RK7532-H018UN VALVE AND TRIGGER ASS'Y 1
20 TP-RK7532-H020N TRIGGER HOUSING 1
25 TP-RK7532-H025-1N "O"RING (SEE KIT# TP-RK7532-H120U) 1
26 TP-RK7532-P3-26 PISTOL GRIP VALVE ASSEMBLY 1
27 TP-RK7532-P3-27 DELRIN PISTOL GRIP HANDLE 1
28 TP-RK7532-H028N SCREW 1
29 TP-RK7532-H029N "O"RING 1
30 TP-RK7532-H030N SEAL RETAINER 1
38 TP-RK7532-H038Y BARREL 1
39 TP-RK7532-H039Y SEAL 1
40 TP-RK7532-H040Y BLEED PLUGE ASSEMBLY 1
41 TP-RK7532-H041Y SEAL 1
42 TP-RK7532-H042Y SEAL 1
43 TP-RK7532-H043N SCREW 1
44 TP-RK7532-H044N PLUG 1
45U TP-RK7532-H045UN TAL JAW CYLILDER 1
46 TP-RK7532-H046N PLUGE 1

11
RK7532-P3 Pantograph Handle/Hose Assembly cont….
Parts List cont….
# Part# Description Qty
47 TP-RK7532-H047Y JAW HOUSING 1
48 ZRT-VJ TAIL JAWS 2
49 TP-RK7532-H049Y "O"RING 2
50U TP-RK7532-H050UY SCREW 2
51 TP-RK7532-H051N END CAP 1
52 TP-RK7532-H052Y NUT 7
53 TP-RK7532-H053N SCREW 2
54 TP-RK7532-H054Y SCREW 3
55 TP-RK7532-H055Y SCREW 2
56 TP-RK7532-H056Y LABEL 2
57 TP-RK7532-H057N HANDLE MOULDING(LEFT) 1
70 TP-RK7532-H070N QUICK RELEASE NIPPLE 1
74 TP-RK7532-H074N "O"RING 1
75 TP-RK7532-H075Y SEAL 1
77 TP-RK7532-H077Y BARREL RETURN SPRING 1
78 TP-RK7532-H078Y SPINDLE 1
78 TP-RK7532-H078N SPINDLE 1
79U TP-RK7532-H079UY ELBOW CONNECTOR 1
81 See Catalog MANDREL 1
82 ZRT-IC CURSOR 1
83 See Catalog M/F SPRING 1
84 See Catalog FRONT JAW (SEE CATALOG FOR P/N) 1
85U TP-RK7532-H085UY SCREW 2
86U TP-RK7532-H086UY NON-RETURN VALVE 1
87U TP-RK7532-H087UY Y-FITTING 1
120U TP-RK7532-H120U TRIGGER ASS'Y KIY, 26, 78, 25, 25-1, 24, 22 1

12
RK7532 Standard Intensifier Assembly

13
General Assembly RK7532 Standard Intensifier Assembly
Parts List
# Part# Description Qty
I001 TP-RK7532-B001N "O"RING (SEE KIT#TP-RK7532-K082) 1
I002 TP-RK7532-B002N SCREW (SEE KIT#TP-RK7532-K082) 1
I003 TP-RK7532-B003N COVER PLATE (SEE KIT#TP-RK7532-K082) 1
I004-U TP-RK7532-B004UY SEAL HOUSING 1
I005-U RP-RK7532-B005UY SEAL 2
I006-U TP-RK7532-B006UY PLUG 1
I007 TP-RK7532-B007Y BODY ASS'Y 1
I008 TP-RK7532-B008N PISTON ROD 1
I009 TP-RK7532-B009Y "O"RING 1
I010 TP-RK7532-B010N AIR PISTON 1
I011 TP-RK7532-B011N END COVER 1
I012 TP-RK7532-B012Y "O"RING 1
I013 TP-RK7532-B013Y RETAINING RING 1
I014 TP-RK7532-B014Y SILENCER 1
I015 TP-RK7532-B015Y SILENCER COVER 1
I016 TP-RK7532-B016N LOCK NUT 1
I017 TP-RK7532-B017Y SPACER 1
I018 TP-RK7532-B018N SCREW 1
I018-1 TP-RK7532-B018-1N WASHER 1
I019 TP-RK7532-B019Y RETAINING PLATE 1
I020 TP-RK7532-BN "O"RING 1
I025 TP-RK7532-B025Y SCREW 2
I026 TP-RK7532-B026Y "O"RING 1
I028 TP-RK7532-B028Y SLEEVE 1
I029 TP-RK7532-B028Y SEAL 1
I030 TP-RK7532-B030N "O"RING 2
I031U TP-RK7532-B031UN SEAL 1

14
RK7532-P3 Linear Arm Assembly
Parts List
# Part# Description Qty
1 TP-RK7532-P001 FOOT 1
2 TP-RK7532-P002 POLE 1
3 TP-RK7532-P003 NEEDLE BUSH 1
4 TP-RK7532-P004 BALANCER SUPPORT 1
5 RP-RK7532-P005 BALANCER, 2.5kg-5.0kg ZERO GRAVITY 1
6 TP-RK7532-P006 SETTING PLATE 1
7 TP-RK7532-P007 SLIDING BUSH 1
8 TP-RK7532-P008 CLAMP 1
9 TP-RK7532-P009 SET OF SLIDES 2
10 TP-RK7532-P010 CLAMP 1
11 TP-RK7532-P011 MAGNET 1
12 TP-RK7532-P012 INLINE CLAMP 1

15
RK7532-P3 Rotation Device Assembly
1
2
3
4
5
6
7
8
9
10
11
12
Parts List
# Part# Description Qty
1 TP-RK7532-R001 ARM MOUNT 1
2 TP-RK7532-R002 FEST VALVE 10748 WITH SMC #AS1200M5 SPEED CONTROL 1
3 TP-RK7532-R003* COVER PLATE & SCREWS *NOT INCL. WITH SOME VERSIONS 1
4 TP-RK7532-R004 DOWEL 1
5 RP-RK7532-R005 WASHER 1
6 TP-RK7532-R006 RETAINING RING 1
7 TP-RK7532-R007 CLEVIS PIN 1
8 TP-RK7532-R008 PIVOT BLOCK 1
9 TP-RK7532-R009 LOCK NUT 1
10 TP-RK7532-R010 PULL BUTTON 1
11 TP-RK7532-R011 TOOL MOUNT 1
12 TP-RK7532-R012 SCREW 1

16
TROUBLESHOOTING
Problem Possible Cause Remedy
Tool will not cycle when
connected to air supply
Low air pressure
Pilot valve sticking
Check air pressure and increase
if necessary
Remove pilot valve spool, clean
and lubricate as detailed on
page 7
Tool will not place fastener High broach load
Worn/dirty tail jaws
Low air pressure
Jaws not gripping mandrel
Air in hydraulic system
Check hole size, fastener and
grip length to ensure correct
fastener is being used in the
application. Check for correct
mandrel
Clean/replace tail jaws
Check air pressure and increase
if necessary
Mandrel worn or broken, replace
with a new mandrel
Re-prime tool
Tool feeds more than one
rivet
Incorrect gap set between head of rivet
and nose jaw
Worn/dirty tail jaws
Worn mandrel
Re-set gap as to 1.5-3mm
Clean/replace tail jaws
Check/replace mandrel
Mandrel will not release
Mandrel Releases too slow
Inadequate SMC Speed Control
Adjustment
Festo Roller Lever Valve R-002 is out of
position
Faulty Fest Roller Lever Valve
Adjust SMC speed Valve on Fest
Valve R002 (Increase flow)
Adjust position using two
screws.
Check Festo Valve Position &
Operation, Replace if neccesary
Mandrel falling out on tool
rotation
Inadequate SMC Speed Control
Adjustment
Adjust SMC speed Valve on Fest
Valve R002 (Decrease flow)
INTENSIFIER SPANNER
Industrial Rivet & Fasteners Co. offers a comprehensive tool service and repair program, for details
contact your local area sales representative or call direct:
200 Paris Avenue
Northvale, NJ 07647
Tel: [phone]
Fax: [phone]

17
Warranty Statement:
Industrial Rivet & Fastener Co. Inc. (hereinafter “IRF”), hereby warrants to the initial retail customer or original
authorized distributor (“Warrantee”) only that its products will be free from defects in material and
workmanship for a period of 1 year from the purchase date provided that the products are used in accordance
with “IRF’s” instructions as to maintenance, operation and use.
The said warranty does not extend to goods subjected to misuse, neglect, accidental/improper installation,
improper maintenance or which have been altered/repaired by anyone other than the seller or its certifiably
authorized agents. The said warranty does not extend to consumable components or wear components as
listed in schedule A.
The warrantee’s only remedy and IRF’s only obligation in the event of a defect or failure in the products, is that
IRF, at its sole option, repair, replace or re work the products, but in no case shall the cost of the foregoing
exceed the invoice price of the products.
This warranty shall be void if any person seeking to make a claim for defective products fails to notify IRF within
30 days, or, if distributor fails to provide evidence that the product failed within 30 days of the failure. Proof
and date of purchase, maintenance records as well as details regarding failure must be sent via e-mail, and a
sample of the failed products sent via postal service is required for warranty evaluation.
This warranty is in lieu of all other warranties, expressed or implied, including merchantability, or
fitness provided for herein. Under no circumstance shall IRF be liable for incidental or
consequential damages arising from the defect or failure in its products.
Seller’s sole obligation under the foregoing warranty will be limited to, at Seller’s option, repair or replacement
of the tool (and shipping to the buyer with transportation charges paid to any place within the contiguous 48
states). Returned goods will be evaluated by our warranty repair department and a conclusion will be
determined and classified as:
a) Warranty Repair (free of charge)
b) Non-Warranty repair or Abuse/Neglect (Hourly rate, Schedule B)
c) Maintenance (Flat Fee, Schedule B)
Schedule A – Limited Warranty
The following are considered consumable or wear parts and are not covered under the warranty.
Consumables: Jaws, Nosepieces, Mandrels, Cursor, Spring
Wear Parts: Mandrel Catcher, O-Rings, Pneumatic Seals, Hydraulic Seals*
*Hydraulic seals have a limited warranty (6 months) and the replacement is at the sole discretion of the
manufacturer.
Schedule B – Maintenance/Repair
Price Schedule as of 1/1/2011
Bench Fee: $ 60.00 (up to one hour)
Hourly Rate: $ 60.00 per hour
Flat Fee: Level 1 - Adjustments, cleaning and light repair $45.00 + parts
Level 2 – Maintenance, Oil Change (Velocite No 10), plus Level 1 service $65.00 + parts
Level 3 – Complete disassembly, change all seals, plus level 2 service $120.00 + parts
If inspection by the seller of returned goods shows no breach of the forgoing warranty, Seller’s regular
conditioning charges (Schedule B) apply. Upon this conclusion we will either repair the tool at no cost to you
and return it postage paid, or call you to inform you of the repair cost. The repair will need to be approved in
writing before any work is performed.
A comprehensive tool service and repair program, for details contact your local area sales representative or call:
Industrial Rivet & Fastener Co.
200 Paris Ave
Northvale, NJ 07647
1-800-BUY-RIVET

Product Name: MOBIL VELOCITE OIL NO. 10
Revision Date: 01Nov2006
Page 3 of 8
_________________________________________________________________________________________________________
_____________
Water Spill: Stop leak if you can do it without risk. Confine the spill immediately with booms. Warn other
shipping. Remove from the surface by skimming or with suitable absorbents. Seek the advice of a
specialist
before using dispersants.
Water spill and land spill recommendations are based on the most likely spill scenario for this material;
however, geographic conditions, wind, temperature, (and in the case of a water spill) wave and current
direction
and speed may greatly influence the appropriate action to be taken. For this reason, local experts should
be
consulted. Note: Local regulations may prescribe or limit action to be taken.
ENVIRONMENTAL PRECAUTIONS
Large Spills: Dike far ahead of liquid spill for later recovery and disposal. Prevent entry into waterways,
sewers, basements or confined areas.
SECTION 7 HANDLING AND STORAGE
HANDLING
Prevent small spills and leakage to avoid slip hazard.
Static Accumulator: This material is a static accumulator.
STORAGE
Do not store in open or unlabeled containers.
SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION
Exposure limits/standards for materials that can be formed when handling this product: When
mists / aerosols
can occur, the following are recommended: 5 mg/m³ - ACGIH TLV, 10 mg/m³ - ACGIH STEL, 5 mg/m³ -
OSHA PEL.
NOTE: Limits/standards shown for guidance only. Follow applicable regulations.
ENGINEERING CONTROLS
The level of protection and types of controls necessary will vary depending upon potential exposure
conditions.
Control measures to consider:
No special requirements under ordinary conditions of use and with adequate ventilation.
PERSONAL PROTECTION
Personal protective equipment selections vary based on potential exposure conditions such as
applications,
handling practices, concentration and ventilation. Information on the selection of protective equipment for
use
with this material, as provided below, is based upon intended, normal usage.
Respiratory Protection: If engineering controls do not maintain airborne contaminant concentrations at a
level which is adequate to protect worker health, an approved respirator may be appropriate. Respirator
selection, use, and maintenance must be in accordance with regulatory requirements, if applicable. Types
of
Product Name: MOBIL VELOCITE OIL NO. 10
Revision Date: 01Nov2006
Page 4 of 8
_________________________________________________________________________________________________________
_____________
respirators to be considered for this material include:
No special requirements under ordinary conditions of use and with adequate ventilation.
For high airborne concentrations, use an approved supplied-air respirator, operated in positive pressure
mode.
Supplied air respirators with an escape bottle may be appropriate when oxygen levels are inadequate,
gas/vapor warning properties are poor, or if air purifying filter capacity/rating may be exceeded.
Hand Protection: Any specific glove information provided is based on published literature and glove

manufacturer data. Work conditions can greatly effect glove durability; inspect and replace worn or
damaged
gloves. The types of gloves to be considered for this material include:
No protection is ordinarily required under normal conditions of use.
Eye Protection: If contact is likely, safety glasses with side shields are recommended.
Skin and Body Protection: Any specific clothing information provided is based on published literature or
manufacturer data. The types of clothing to be considered for this material include:
No skin protection is ordinarily required under normal conditions of use. In accordance with good
industrial hygiene practices, precautions should be taken to avoid skin contact.
Specific Hygiene Measures: Always observe good personal hygiene measures, such as washing after
handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and
protective
equipment to remove contaminants. Discard contaminated clothing and footwear that cannot be cleaned.
Practice good housekeeping.
ENVIRONMENTAL CONTROLS
See Sections 6, 7, 12, 13.
SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES
Typical physical and chemical properties are given below. Consult the Supplier in Section 1 for
additional
data.
GENERAL INFORMATION
Physical State: Liquid
Color: Amber
Odor: Characteristic
Odor Threshold: N/D
IMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATION
Relative Density (at 15 C ): 0.861
Flash Point [Method]: >174C (345F) [ ASTM D-92]
Flammable Limits (Approximate volume % in air): LEL: 0.9 UEL: 7.0
Autoignition Temperature: N/D
Boiling Point / Range: > 316C (600F)
Vapor Density (Air = 1): > 2 at 101 kPa
Vapor Pressure: < 0.013 kPa (0.1 mm Hg) at 20 C
Evaporation Rate (n-butyl acetate = 1): N/D
pH: N/A
Log Pow (n-Octanol/Water Partition Coefficient): > 3.5
Solubility in Water: Negligible
Viscosity: 22 cSt (22 mm2/sec ) at 40 C | 4 cSt (4 mm2/sec) at 100C
Product Name: MOBIL VELOCITE OIL NO. 10
Revision Date: 01Nov2006
Page 5 of 8
_________________________________________________________________________________________________________
_____________
Oxidizing Properties: See Sections 3, 15, 16.
OTHER INFORMATION
Freezing Point: N/D
Melting Point: N/A
Pour Point: -21°C (-6°F)
DMSO Extract (mineral oil only), IP-346: < 3 %wt
SECTION 10 STABILITY AND REACTIVITY
STABILITY: Material is stable under normal conditions.
CONDITIONS TO AVOID: Excessive heat. High energy sources of ignition.
MATERIALS TO AVOID: Strong oxidizers
HAZARDOUS DECOMPOSITION PRODUCTS: Material does not decompose at ambient temperatures.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION 11 TOXICOLOGICAL INFORMATION

ACUTE TOXICITY
Route of Exposure Conclusion / Remarks
Inhalation
Toxicity (Rat): LC50 > 5000 mg/m3 Minimally Toxic. Based on test data for structurally similar
materials.
Irritation: No end point data. Negligible hazard at ambient/normal handling temperatures.
Based on assessment of the components.
Ingestion
Toxicity (Rat): LD50 > 2000 mg/kg Minimally Toxic. Based on test data for structurally similar
materials.
Skin
Toxicity (Rabbit): LD50 > 2000 mg/kg Minimally Toxic. Based on test data for structurally similar
materials.
Irritation (Rabbit): Data available. Negligible irritation to skin at ambient temperatures. Based on test
data for structurally similar materials.
Eye
Irritation (Rabbit): Data available. May cause mild, short-lasting discomfort to eyes. Based on test
data for structurally similar materials.
CHRONIC/OTHER EFFECTS
Contains:
Base oil severely refined: Not carcinogenic in animal studies. Representative material passes IP-346,
Modified
Ames test, and/or other screening tests. Dermal and inhalation studies showed minimal effects; lung
nonspecific
infiltration of immune cells, oil deposition and minimal granuloma formation. Not sensitizing in test
animals.
Additional information is available by request.
Product Name: MOBIL VELOCITE OIL NO. 10
Revision Date: 01Nov2006
Page 6 of 8
_________________________________________________________________________________________________________
_____________
The following ingredients are cited on the lists below: None.
--REGULATORY LISTS SEARCHED--
1 = NTP CARC 3 = IARC 1 5 = IARC 2B
2 = NTP SUS 4 = IARC 2A 6 = OSHA CARC
SECTION 12 ECOLOGICAL INFORMATION
The information given is based on data available for the material, the components of the material, and
similar materials.
ECOTOXICITY
Material -- Not expected to be harmful to aquatic organisms.
MOBILITY
Base oil component -- Low solubility and floats and is expected to migrate from water to the land.
Expected to
partition to sediment and wastewater solids.
PERSISTENCE AND DEGRADABILITY
Biodegradation:
Base oil component -- Expected to be inherently biodegradable
BIOACCUMULATION POTENTIAL
Base oil component -- Has the potential to bioaccumulate, however metabolism or physical properties
may
reduce the bioconcentration or limit bioavailability.
SECTION 13 DISPOSAL CONSIDERATIONS
Disposal recommendations based on material as supplied. Disposal must be in accordance with current
applicable
laws and regulations, and material characteristics at time of disposal.
DISPOSAL RECOMMENDATIONS
Product is suitable for burning in an enclosed controlled burner for fuel value or disposal by supervised