iNels eLAN-RF-Wi-003St User manual

15.11.2019 Page 1of 17
eLAN-RF-Wi-003
02-32/2017 / rev.7
15.11.2019

15.11.2019 Page 2of 17
eLAN-RF-Wi-003
02-32/2017 / rev.7
15.11.2019
1. Introduction..................................................................................................................................... 4
2. Installing the application ................................................................................................................. 5
3. Logging in to the web interface eLAN-RF-Wi-003 ........................................................................... 6
4. Settings............................................................................................................................................ 7
Description of functions ...................................................................................................................... 8
Adding RF actuators to the floorplan ................................................................................................ 16
RF control actuators .......................................................................................................................... 17
Starting up scenes ............................................................................................................................. 17

15.11.2019 Page 3of 17
eLAN-RF-Wi-003
02-32/2017 / rev.7
15.11.2019
Before you begin
The instruction manual provides information on installing and operating the device. The instruction manual is
always a part of the supply. Only perform installation after becoming thoroughly familiar with this User Guide and
device functions. Problem-free function of the device also depends on the way it was shipped, stored and
handled. If you notice any signs of damage, deformation, malfunction or a missing part, do not install this product
and return it to the point of sale. At the end of its service life, the product and its parts must be treated as
electronic waste. Before starting the installation, make sure that all wires and connected parts are not under
voltage. When assembling and performing maintenance, you must uphold safety regulations, standards,
directives and special provisions for working with electrical equipment.

15.11.2019 Page 4of 17
eLAN-RF-Wi-003
02-32/2017 / rev.7
15.11.2019
1. Introduction
Congratulations on purchasing the Smart RF box eLAN-RF-Wi-003 control unit, an element of the RF
Control wireless system.
• The smart RF box Enables you to control your electrical installation by smartphone,
tablet, Samsung smart-watch Gear S2 or SMART TV.
• It transmits and receives commands of up to 40 units, and it processes set programs for automatic
control, (you can gradually expand installation from 1 unit iNELS RF Control).
• Thanks to bi-directional communication, it visualizes the current status of individual units.
• The RF Smart box eLAN-RF-Wi003 is connected to the home network (router) using a network LAN
cable. After the initial connection a WiFi network can then be used to communicate with
a smartphone. The defaults are set on the DHCP Server, for connection to a home network, you
must first configure it using a PC. WiFi module functions only if you do not have your own WiFi
network and you want to connect directly to an eLAN application.
• The intuitive application environment offers central control from one place.
• Function of application iHC-MAIRF / iHC-MIIRF / iHC-WTRF:
- control of hot water or electric underfloor heating
- measuring temperature by wireless sensors
- switching appliances (garage door, blinds, fan, sprinklers, sockets, etc.)
- dimming lights (LED, energy-saving, halogen or classic lamps)
- time switching (delayed switching off of light when leaving room)
- video camera integration
- scenes (make multiple commands at once with a single press).
• Power is supplied to the Smart RF box via adapter 10-27V DC (included in the supply) or PoE by
power source (router) 24V DC.
• By connecting two Smart RF boxes by LAN cable, you avoid the problem of lack of signal range.
• Option of setting via web interface or directly in the application iHC-MAIRF (Android) / iHC-MIIRF
(iPhone).
• The package includes an internal antenna AN-I, in case the Smart RF box is located in a metal
switchboard, you can use the external antenna AN-E for better signal reception.*
• Range up to 100 m (in open space), if the signal is insufficient between the Smart RF box and unit,
use the signal repeater RFRP-20.
• Communication frequency with bidirectional protocol iNELS RF Control.
* Max Tightening Torque for antenna connector is 0.56 Nm.
Attention:
The minimum distance between the controller (system unit) and the actuator must not be less than
one centimeter.
Setting options:
• max. number of actuator - 40
• max. number of temperature zones - 16
• max. number of time schedules - 16
• max. number of central sources - 10
• max. number of heating and cooling devices in a heating zone - 10
• max. number of intervals in a time schedule – 8

15.11.2019 Page 5of 17
eLAN-RF-Wi-003
02-32/2017 / rev.7
15.11.2019
List of usable ports:
More detailed description of the port use:
https://en.wikipedia.org/wiki/List_of_TCP_and_UDP_port_numbers
2. Installing the application
Install the application in your smartphone:
for mobile telephone with OS Android: download the current version at Google Play (under the
name iHC-MAIRF).
https://play.google.com/store/apps/details?id=cz.elkoep.ihc_marf_us&hl=en
for mobile telephones with IOS: download the current version under the name iHC-MIIRF in the
app store.
https://itunes.apple.com/cz/app/inels-home-control-rf-for-iphone/id1189384684?mt=8

15.11.2019 Page 6of 17
eLAN-RF-Wi-003
02-32/2017 / rev.7
15.11.2019
3. Logging in to the web interface eLAN-RF-Wi-003
After connecting the eLAN-RF-Wi-003 to the power source, after around 1 minute you will see
displayed in the list of available WiFi networks the name: ELAN-RF-WI
Connect to the network by entering the password: 00000000
Write into the panel Address (in the Internet browser) the set IP address of the product eLAN-
RF-Wi-003. (Upon the first configuration, enter the factory-assigned default IP address:
192.168.1.1)
After confirming the entered IP address, the web server's login page will come up.
The factory settings for signing in as administrator are:
Login: admin
Password: elkoep
Login options:
It is possible to log into the eLAN-RF-Wi-003 web interface either as the administrator
(admin) with full access to controls and settings, or as the user (user), for whom only the
panel itself is displayed.
The user thus only has the option of controlling the device (the factory setting of the password
for logging in as admin and user is: elkoep).
Both users log into the same dialog field (Login, Password), but each uses his/her own name
and password.
Confirm the log in by pressing: Login.
Note:
Perform RESET of the eLAN-RF-Wi-003 by a long press of the button on the front panel of the device until the
yellow LED begins flashing. eLAN is restarted at the moment the LED stops flashing. The IP address and login
data return to factory settings.

15.11.2019 Page 7of 17
eLAN-RF-Wi-003
02-32/2017 / rev.7
15.11.2019
4. Settings
After logging in your browser opens a window where you can see the devices associated to the room.
If you set multiple rooms, you can switch between them by arrows, located in the upper right corner.
Clicking on the Settings icon displays the menu

15.11.2019 Page 8of 17
eLAN-RF-Wi-003
02-32/2017 / rev.7
15.11.2019
Description of functions
By clicking on the Setting elan the basic menu settings are displayed.
By pressing Log out, you will log out of the web interface
eLAN-RF-Wi-003.
By pressing the button Accounts, you will display a window
for changing login data.
By pressing the button Load settings, you can restore your stored settings, which you have
already stored in your PC (the file has the extension .bin).

15.11.2019 Page 9of 17
eLAN-RF-Wi-003
02-32/2017 / rev.7
15.11.2019
By pressing the button Save settings, you can save the current settings of your eLAN-RF-Wi-003
including network settings.
The button Settings is to configure network settings that you can change any time based on your
network.
If you leave DHCP enabled selected by default, the eLAN-RF-Wi-003 always assigns you an IP
address in the range set by default (192.168.1.x).
The IP address of eLAN-RF-Wi-003 can be changed, but in the same range.
If you have your own home Wi-Fi network, switch to Static IP and set the IP of the eLAN-RF in the
same subnet mask as you have at home. Set the default gateway the same as your network.
Press Save to store the settings. If you can connect the eLAN-RF-Wi-003 by ethernet cable into
your home network.
Note: If you change the IP address, to log into the eLAN-RF-Wi-003 you must use the new IP address.
If the new IP address that you entered is not in the same subnetwork, the connection will not work if
settings are not changed in the connected device (PC, iMM Client) to the same subnetwork.
The button Update firmware is used to update the firmware (FW).
When updating the eLAN-RF-Wi-003, proceed according to the following instructions:
1 Download the latest firmware version from the website: http://www.elkoep.com/products/inels-rf-
control/system-units/smart-rf-box-elan-rf-wi-003-8487/
2 Click on the button Update firmware, select the downloaded file (the update file must always
include the extension *.bin ), and click on it. After confirming by pressing OK, the update of your
firmware in your eLAN-RF-Wi-003 automatically starts.
Note: do not turn off device or use the Reset button when updating the firmware. the eLAN-RF-Wi-003 restarts
after updating. After the firmware update, all settings will remain preserved. This means that the set IP, login data,
visualization panel will remain the same as with the SW version prior to the update. Perform the FW update if you
are connected to the application in the local network. Using a public address, the upgrade may not always
succeed (this also applies to VPN connections).

15.11.2019 Page 10 of 17
eLAN-RF-Wi-003
02-32/2017 / rev.7
15.11.2019
The button RF mode is used to switch the mode of your eLAN-RF-Wi-003.
Repeater
The Repeater function is an independent function of eLAN-RF-Wi-003 and is used to increase range
between RF controllers (system elements) and RF elements.
Use: an eLAN-RF-Wi-003 device configured for a repeater can only be connected to the supply
voltage, and it will then function just the same as the RFRP-20. This means if it receives a command
from the RF controller or RF detector, it resends it to a designated RF element and vice-versa.
Oasis Compatible
Enables the repeater function to serve unidirectionally communicating units (RF Key, RFWB, RFIM,
detectors, etc.).
RF Touch compatible
Enables the repeater function to serve bidirectionally communicating units (RF Touch, RF Pilot, etc.).
List of addresses

15.11.2019 Page 11 of 17
eLAN-RF-Wi-003
02-32/2017 / rev.7
15.11.2019
Repeated address settings - write into the list of addresses those elements with which you want the
eLAN RF. If you set the eLANs to the router mode, the same addresses must be set for both eLANs…
After setting the function Repeater, eLAN restarts.
Router
The Router function is used to extend the distance and control of RF elements by connecting two
eLANs into the LAN network.
The first eLAN (so-called Master ) must be set during configuration in the Router function, it
receives all RF commands of controllers via an RF signal. It assess the limitations and
permissions of addresses.
The second eLAN (so-called Slave) assess all commands from the eLAN Master determined
for sending by RF signal. It sends valid messages by RF signal to controlled elements. If a
response comes from an element, it sends it to the eLAN Master.
It is necessary to enter into the settings the LAN parameters of the second eLAN - Slave (IP
address, login data).
The second eLAN Slave can be configured in two ways.
Active function Repeater – this receives commands via the Ethernet network and via the
RF network.
Example: eLAN Slave catches the RF signal of the RF controller, saves it as Repeater
(signal repeater), and sends the RF signal further along.
Active function Router – eLAN is in its basic setting. eLAN only receives commands from
the Ethernet network, and ignores all RF signals.
Oasis Compatible
The sames as with the Repeater function.
RF Touch Compatible
The sames as with the Repeater function.
List of addresses
The sames as with the Repeater function. The same addresses must be set for both eLANs.
After setting the function Router, eLAN restarts.

15.11.2019 Page 12 of 17
eLAN-RF-Wi-003
02-32/2017 / rev.7
15.11.2019
Button Reboot –to restart the device eLAN-RF-Wi-003.
Button Date & Time
Here the IP address of the NTP server is set by default, which determines for the eLAN the precise
time via the Internet. You can also set the time zone in which the eLAN is located. By selecting
Daylight Saving Time, you can manually set the daylight saving time.
Time of eLAN-RF-Wi-003 is automatically set from NTP server.
If your eLAN-RF-Wi-003 is not connected to internet network, then time is always set to 12:00 AM, the
current day is set manually with button Manual.
During power failure, time information is erased from eLAN memory.
Button Wifi settings –used to change the name of the WiFi network and password for the
connection.

15.11.2019 Page 13 of 17
eLAN-RF-Wi-003
02-32/2017 / rev.7
15.11.2019
Button Devices is used for adding RF actuators to the eLAN-RF-Wi-003.
Button (+) - add a new RF element:
1. Product Type –select RF element
2. Address –enter the address of the RF element that is listed right on the box of the added
EF element (six-character code).
3. Label - any naming of the element, e.g. "Kitchen light".
4. Type - select the type of icon (e.g. light), which will be displayed on the floorplan.
Create, you will store the RF actuator in the eLAN-RF-Wi-003.
Button - remove all elements.

15.11.2019 Page 14 of 17
eLAN-RF-Wi-003
02-32/2017 / rev.7
15.11.2019
Button Rooms displays created rooms.
By pressing the button (+).
If you click on the button (+), a table is displayed in which you fill in:
1. Label gives an arbitrary name to the room (you can use diacritical marks, gaps and others...)
2. Type –here you select the type of room or type of icon that you will then display after entering
the floorplan on the desktop.
3. Floorplan –here select the floorplan (image) that you added before in the tab Floorplans.
By pressing you can remove all added rooms.
Name of room

15.11.2019 Page 15 of 17
eLAN-RF-Wi-003
02-32/2017 / rev.7
15.11.2019
Buttonl Scenes –Here any scenes are created based on user requirements.
It is possible to create scenes only after you add rooms and actuators.
Button (+) - add a new scene:
1. Label - enter any name of the scene (you can use diacritical marks and spaces in
between…).
2. Actions - (+) –add an RF element.
When adding an actuator, its function-action is set switching, dimming, etc.).
If for an actuator, you select the function ON, you must still confirm this function by its precise status in
the table Choose value, e.g. true –for switching on or false –switching off.
After adding all actuators and their required functions, click on Create, thereby saving the entire
scene.

15.11.2019 Page 16 of 17
eLAN-RF-Wi-003
02-32/2017 / rev.7
15.11.2019
Button Floorplans here you can add floorplans (images, layouts….).
Button (+) - add a new floorplan:
1. Select the required image for the floorplan (stored in your PC).
2. ID –enter the name of the floorplan. Confirm by pressing OK.
The number of floorplans is limited by the memory size of the eLAN-RF-Wi-003.
Memory Status, see the icon on the top toolbar.
Adding RF actuators to the floorplan
Click on Rooms in the room panel, where you want to add the required RF components. On the
desktop menu the room appears (there any correction can be made).
Click the Continue button to display a list components associated with the eLAN. Click on individual
elements to add to the room.
- If a floor plan is assigned to a room, you can move the components in the room freely.
- If a floor plan is not assigned to a room, the components are ranked next to each other and
you cannot assign them to move over the area freely.
Save by clicking on the Create button.
Deleting components from the room is carried out using the Help
application.

15.11.2019 Page 17 of 17
eLAN-RF-Wi-003
02-32/2017 / rev.7
15.11.2019
RF control actuators
-Mobile phone help application
-Clicking on the component icon (1) to start the function settings (switch-off delay ...).
-Click on the name of the component (2) to display all its functions, where you can select which
function is performed (delayed closing - including setup time, brightness adjustment ...).
Thermal components can only be controlled by the application on your phone; on the web interface
only the information about the measured / set temperature is displayed.
Starting up scenes
- Clicking on the icon Scenes (3) displays a list of pre-set scenes.
- Click on the scene you want to start setting the scene (turn off all-delay ...).