Infineon Traveo II CPU board User manual

www.infineon.com
Please note that Cypress is an Infineon Technologies Company.
The document following this cover page is marked as “Cypress” document as this is the
company that originally developed the product. Please note that Infineon will continue
to offer the product to new and existing customers as part of the Infineon product
The fact that Infineon offers the following product as part of the Infineon product
portfolio.
Continuity of document content
portfolio does not lead to any changes to this document. Future revisions will occur
when appropriate, and any changes will be set out on the document history page.
Continuity of ordering part numbers
Infineon continues to support existing part numbers. Please continue to use the
ordering part numbers listed in the datasheet for ordering.

CYTVII-B-E-100-SO board quick start guide
Traveo™ II CPU board
Kit contents:
1. Traveo™ II CPU board (CYTVII-B-E-100-SO)
2. Mini-B USB cable
3. 12-V universal power adapter
4. Quick start guide (this document)
5. Screws and spacers

Traveo™ II CPU board
• Ensure that jumpers J23 (pins 1 & 2), J5, J6, J7, J9, J10
are shorted. Connect the 12-V adapter to the power jack (J3).
CYTVII-B-E-100-SO board quick start guide
•Insert the Traveo™ II device into the IC socket (U3).
Align Pin 1 with the arrow mark near C16 and close
the socket cover.
•Connect an appropriate progamming tool (IAR/GHS)
to one of the debug interface (J17, J18, J19, J20).
• Toggle switch SW1 to the upper position to turn ON
the board. The PWR LED should glow.
• Use an appropriate IDE on a PC to load a rmware SREC le into the device ash. The LED blink rmware is available in
the release package.
12
4
3

CYTVII-B-E-100-SO board quick start guide
Traveo™ II CPU board
Instructions:
Use the board in conjunction with the body controller baseboard (CYTVII-B-E-BB) to evaluate all features of the
Traveo™ II MCU. In standalone mode, only limited features of the MCU are available.
See the CPU board user guide for details.
• User guide
•Schematic
• Sample driver library (SDL)
• Software examples
Go to the customer support portal (cypress.com/support) to know more about the baseboard and
compatibility, and for the following resources:
CYTVII-B-E-BB
CYTVII-B-E-100-SO

CYTVII-B-E-100-SO board quick start guide
Traveo™ II CPU board
Traveo™ II CPU board details
1. Jumper for GND probe – J2
2. Power connector 12V – J3
3. Jumper to switch PMIC/LDO mode – J23
4. PMIC controller (S6BP201A) – U1
5. CPU board power switch – SW1
6. CPU board power LEDs – LD2
7. USB-UART Tx LED – LD3
8. USB-UART Rx LED – LD4
9. USB serial controller (CY7C65213) – U5
10. Mini-B USB connector – J12
11. Jumper for USB-UART Rx – J13
12. Jumper for USB-UART Tx – J11
13. User LED – LD5
14. Jumper for user LED – J15
15. MCU reset LED – LD6
16. GND test probe point – TP8
17. IDC Arm®standard JTAG 20-pin connector – J20
18. Arm®Cortex®debug MIPI-10 connector – J19
19. Arm®Cortex®debug ETM MIPI-20 connector – J18
20. Arm®ETM Mictor-38 connector – J17
21. Jumper for GND probe – J16
22. User switch – SW3
23. Jumper for user switch – J14
24. Traveo™ II TVII-B-E-100 device (CYT2Bx5) – U3
25. MCU reset switch – SW2
26. MCU reset LED – LD1
27. MCU reset controller jumper – J9
28. External clock input SMA connector – J7
29. MCU power jumpers – J6, J8, J10
30. Jumper for GND probe – J1
1
2
3
4
5
6
7
8
9
10
11
12
15
13
14
16
17
18
19
20
21
22
23
24
25
26
27
28
30
29
© 2018-2021 Cypress Semiconductor Corporation, an Inneon Technologies
Company. All rights reserved. All trademarks or registered trademarks referenced
herein are the property of their respective owners. 002-25012 Rev.*C