Infineon PSoC 62S4 User manual

1 KitProg3 status LED (D10)
2 KitProg3 USB connector (J10)
3 PSoC 5LP programming header (J7)*
4 2.5 V selection jumper (J14)
5 PSoC 6 MCU power selection jumper (J12)
6 PSoC 5LP based KitProg3 programmer
and debugger (CY8C5868LTI-LP039, U7)
7 PSoC 6 MCU current measurement jumper (J13)
8 KitProg3 programming mode selection button (SW3)
9 Power LED (D14)
10 PSoC 6 MCU reset button (SW1)
11 Arduino™ UNO R3 compatible power header (J1)
12 PSoC 6 MCU 10-pin SWD/JTAG program and debug header (J8)
13 User LEDs (D12 and D13)
14 Arduino UNO R3 compatible I/O headers (J2, J3 and J4)
15 PSoC 6 MCU user button/hibernate wakeup (SW2)
16 PSoC 6 MCU (CY8C6244LQI-S4D92, U8)
17 CapSense™ buttons and slider (CSB1, CSB2 and CSS1)
18 Thermistor (TH1)
19 Ambient light sensor (Q8)
20 QSPI NOR flash (S25FL512SAGMFIR10, U9)
21 PSoC 6 MCU USB connector (J5)
22 PSoC 6 MCU extended I/O header (J11)*
23 External power supply connector (J9)*
* Footprint only, not populated on the board
PSoC 62S4 pioneer board details
PSoC 62S4 pioneer board pinout details
www.cypress.com/CY8CKIT-062S4
Quick start guide
PSoC™ 62S4 pioneer kit
CY8CKIT-062S4
The PSoCTM 62S4 pioneer kit (CY8CKIT-062S4) is a low-cost hardware
platform that enables you to design and debug applications using
the PSoC 62 MCU.
Kit contents
PSoC 62S4 pioneer board
USB type-A to micro-B cable
Six jumper wires (five inches each)
Quick start guide (this document)
›
›
›
›
1
2
3
4
5
6
7
8
9
10 11 12 14
13 15 16
17
18
1921 20142223
P6_4/SCL
P6_5/SDA
VREF/AREF
GND/GND
P2_2/D13
P2_1/D12
P2_0/D11
P2_3/D10
P2_6/D9
P2_4/D8
P6_3/D7
P6_2/D6
P5_7/D5
P5_6/D4
P5_1/D3
P5_0/D2
P0_3/D1
P0_2/D0
P8_1
P8_0
P7_3
P7_2
P7_1
P7_0
P2_7
P2_5
P0_4
P0_5
Arduino Uno R3 I/Os
LEGEND
PSoC 6 MCU I/Os
NC
VTARG/IOREF
XRES/RESET
V 3.3/3.3 V
V 5.0/5 V
GND/GND
GND/GND
VIN/Vin
P10_0/A0
P10_1/A1
P10_2/A2
P10_3/A3
P10_4/A4
P10_5/A5
P10_6
P10_7
P9_0
P9_1
NC
NC
P9_2
P9_3
P3_0
P3_1

Date: 03/2021 All rights reserved. ©2021 Infineon Technologies AG
Before you start
› Ensure that you have the following:
• PC with USB port
• UART terminal soware such as Tera Term
or Minicom
› Visit the kit website to download and install the
required soware.
› Ensure the jumper J12 is at position 2-3 to select 3.3 V.
› Connect the KitProg3 USB connector (J10) to your PC.
› Wait for the driver installation to complete.
Step 1: Connect the kit with UART terminal soware
› Open the UART terminal soware and connect to
the kit’s USB-UART COM port with the following settings:
• Baud rate: 115200 bps
• Data: 8 bit
• Parity: None
• Stop bit: 1 bit
• Flow control: None
› Press the XRES switch (SW1) to reset the device.
Step 2: Run the pre-programmed code example
› Follow the instructions displayed on the UART
terminal to use the pre-programmed
code example.
Step 3: Observe the user LED (D13) brightness variation
› Observe the state of the user LED (D13) with the variation
of ambient light intensity. The LED turns ON when the
ambient light intensity is lower than 45% and turns OFF
when higher than 55%.
Quick start guide
PSoC 62S4 pioneer board
USB-UART COM port setup
Instructions displayed on the UART terminal
Observe the brightness in LED (D13)
Document Number: 002-30749 Rev. *C