Infineon PSoC 62S2 User manual

-
QUICK START GUIDE
PSoC™ 62S2 Evaluation Kit
CY8CEVAL-062S2
www.infineon.com/CY8CEVAL-062S2
Kit contents
1. PSoC™ 62S2 Evaluation Board
2. USB Type-A to Micro-B cable
3. Four jumper wires (four inches each)
4. Two jumper wires (five inches each)
5. Quick start guide (this document)

Quick Start Guide
Before you start
1. Ensure that you have the following:
–PC with USB port
–UART terminal soware such as Tera Term
or Minicom
2. Visit the kit webpage to download and install the
required soware.
Connect and power up the board
1. Ensure that jumper J18 is at position 3–5 to select 3.3 V.
2. Connect the KitProg3 USB connector (J9) to your PC.
3. Wait for the driver installation to complete.
Next steps
Visit the kit webpage for information on code examples supported for this kit and kit documentation.
Page 2 of 4
1
Connect the kit with the UART terminal soware
1. Open the UART terminal soware and connect
to the kit’s USB-to-UART COM port with the
following settings:
–Baud rate: 115200, Data: 8 bit, Parity: None,
Stop bit: 1 bit, Flow control: None
2. Press the XRES button (SW1) to reset the device.
USB cable connected to the
KitProg3 USB connector
2USB-to-UART COM port setup
Run the pre-programmed code example
1. Observe the “Hello World!!!” message on the serial
terminal and confirm that the user LED blinks at 1 Hz.
2. Press the Enter key to pause or resume blinking the user
LED.

Quick Start Guide Page 3 of 4
PSoC™ 62S2 Evaluation Board details
1 KitProg3 USB connector (J9)
2 KitProg3 status LED (D4)
3 KitProg3 (PSoC™ 5LP) programmer and
debugger (CY8C5868LTI-LP039, U2)
4 PSoC™ 6 MCU (CY8C624ABZI-S2D44, U1)
5 QSPI F-RAM (CY15B104QSN, U4)
6 KitProg3 programming mode selection button (SW3)
7 OPTIGA™ Trust M security controller (SLS32AIA, U5)
8 512-Mbit serial NOR flash memory (S25FL512S, U3)
9 PSoC™ 6 MCU USB device connector (J14)
10 System power (VTARG) selection jumper (J18)
11 Headers compatible with mikroBUS by Mikroelektronika
(J19, J23)
12 PSoC™ 6 MCU user buttons (SW2, SW4)
13 Potentiometer (R57)
14 Potentiometer connection jumper (J21)
15 PSoC™ 6 MCU reset button (SW1)
16 PSoC™ 6 MCU VDDIO0 current measurement jumper (J20)*
17 PSoC™ 6 MCU 10-pin SWD/JTAG program and
debug header (J24)
18 PSoC™ 6 MCU debug and trace header (J22)*
19 Power LED (D6)
20 CAPSENSE™ slider (CSS1) and buttons (CSB1, CSB2)
21 PSoC™ 6 MCU VDDIO2 current measurement jumper (J17)
22 PSoC™ 6 MCU VDDIO2 power selection jumper (J16)
23 PSoC™ 6 MCU VTARG current measurement jumper (J15)
24 Power header compatible with Arduino Uno R3 (J1)
25 I/O headers compatible with Arduino Uno R3 (J2, J3, J4)
26 M.2 interface connector (J13)
27 Custom M.2 interface selection jumper (J12)
28 VBAT current measurement jumper (J11)
29 VBAT power selection jumper (J10)
30 PSoC™ 6 MCU user LEDs (D1, D2)
31 RGB LED (D3)
32 GPIO header (J5) for AIROC™ Wi-Fi & Bluetooth®
combo chips*
33 PSoC™ 6 MCU I/O headers (J6, J7)*
34 External power supply VIN connector (J8)
35 microSD card holder (J27)**
* Footprint only, not populated on the board
** Component is located at the bottom side of the board
1
34 3325
2
3
4
5
6
7
8
9
11
12
13 14 15 35 17 20
21
22
23
25
24
26
27
28
29
30
31
32
18 19
16
10

Quick Start Guide Page 4 of 4
PSoC™ 62S2 Evaluation Board pinout details
I/Os compatible with Arduino Uno R3 PSoC™ 6 MCU I/Os
Note: *Not connected
Interface compatible with mikroBUS by Mikroelektronika
LEGEND
AN/P_
RST/P_
CS/P_
SCK/P_
MISO/P_
MOSI/P_
.V
GND
P_/SCL
P_/SDA
VREF/AREF
GND/GND
P_/D
P_/D
P_/D
P_/D
P_/D
P_/D
.V
GND
BT_IS_CLK
BT_IS_WS
BT_IS_DO
BT_IS_DI
BT_GPIO_
BT_GPIO_
BT_GPIO_
BT_GPIO_
BT_GPIO_
M_SCL
M_SDA
V
VCC_VDDIO
BT_UART_RXD
BT_UART_TXD
BT_UART_CTS
BT_UART_RTS
WL_UART_RX
WL_UART_TX
GPIO/WL_UART_RTS
WL_REG_ON_ALT
BT_GPIO_
GND
GND
P_/D
P_/D
P_/D
P_/D
P_/D
P_/D
P_/D
P_/D
P_
P_
P_*
P_*
P_*
P_*
P_*
P_*
P_*
P_
P_*
P_
P_
P_
P_
P_
P_
P_
P_
P_*
NC
VTRAG/IOREF
XRES/RESET
V./V.
V./V.
GND/GND
GND/GND
VIN/VIN
P_/A
P_/A
P_/A
P_/A
P_/A
P_/A
P_/A*
P_/A*
P_/A
P_/A
P_/A
P_/A
P_/A
P_/A
P_/A*
P_/A*
PWM/P_
INT/P_
RX/P_
TX/P_
SCL/P_
SDA/P_
V
GND
Date: 06 / 2023
All rights reserved. © 2023
Infineon Technologies AG
Document number: 002-33159 Rev. *E
For additional details, see the kit guide available on the Infineon kit webpage.