Infomir MAG420 User manual

Instruction Manual
Linux based
Set-Top Box
MAG420
MAG420w1

Regulatory information
EU
This equipment has been tested and found to comply
with the essential requirements of the following
Directives: 2014/30/EU, 2014/35/EU, 2014/53/EU,
2009/125/EC, 2011/65/EU. This product is in
accordance with Directive WEEE (2012/19/EU).
Hereby, Telecommunication Technology LLC declares
that MAG420w1 with the radio equipment type
802.11b/g/n is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is
available at the following internet address:
www.infomir.eu/eng/support/declarations
FCC Compliance Statement
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment to an outlet on a circuit dierent from
that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician
for help.
FCC Caution:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received, including
interference that may cause undesired operation.
CAUTION:
Unauthorized antennas, modications, or attachments
could damage the device and violate FCC regulations.
Changes or modications not expressly approved by
responsible party could void the user’s authority to operate
the equipment.

FCC Radiation Exposure Compliance
(only for MAG420w1):
This equipment complies with radio frequency (RF)
exposure limits set forth by the Federal Communications
Commission for an uncontrolled environment. This
equipment should be installed and operated with a
minimum distance of 20 centimeters between the
radiator and your body. This transmitter must not be
co-located or operating in conjunction with any other
antenna or transmitter.
Note: Specications are subject to change without
notice. Infomir reserves the right to revise this publication
and to make changes in its content from time to time
by posting new specications and other content at
www.infomir.eu.
Regulatory information

Warranty term:
Europe, MEASA and Oceania:
2 years from date of sale (but not more than
2,5 years from manufacture date).
The USA, Americas, Russia, Ukraine and other
regions:
1 year from date of sale (but not more than
1,5 years from manufacture date).
See the date of manufacture at «Product
Information» section. By virtue of the present
Coupon, the absence of defects in manufacturing
of the product and its compounds is warranted for
a year-term counted since date of sale. If during the
mentioned warranty term the defects of materials
or operation of product will be found, the product
would be repaired or its defective parts would be
replaced free of charge in the warranty processing
center with compliance with warranty conditions.
Warranty
Warranty Service Coupon
(to be lled in by a shop-assistant)
Date of Sale:
Company-Seller:
Address of Company-Seller:
Place of Stamp
I have no claims as to appearance and
package contents. I accept the conditions
of warranty service.
Signature of Customer:
Manufacturer:
Telecommunication Technologies LLC
1 Mytna Square, Odesa, 65026, Ukraine

Warranty Processing Centers List:
Europe:
ZLS Services GmbH
Hamburger Allee 56
60486, Frankfurt am Main, Germany
Tel: [phone]
e-mail: [email protected]om
The USA, Canada and Latin America:
Infomir USA
174 Bay 49th Street
Brooklyn, NY 11214 USA
Tel: [phone]
e-mail: [email protected]
MEASA and Oceania:
PROGRESSIVE TECHNOLOGY F.Z.E
Warehouse B1-40
Sheikh Rashid Bin Saeed Al Maktoum Street
Ajman Free Zone
45573, Ajman, UAE
Tel: [phone]
e-mail: [email protected]om
Russia, Belarus:
Tel.: [phone]
e-mail: [email protected]om
Ukraine:
Telecommunication Technologies LLC
4/D, Nebesnoi Sotni Avenue
Odesa, 65121, Ukraine
Tel: [phone]
e-mail: [email protected]om
Warranty processing centers

Warranty conditions
1. The present warranty is only valid if the defective
product is provided with property lled in Warranty
Service Coupon. If date of sale is not pointed, the
warranty term is counted since date of the product
manufacturing which is dened under serial number.
Warranty processing center reserves the right to
refuse free warranty service and parts replacement
in case the mentioned above documents are
not presented or the lled in it information is not
complete or unreadable.
2. The present warranty does not enable the right for
compensation and cover of loss received as a result
of rearrangement of the product.
3. The present guarantee is invalid if model or serial
number of the product is altered, erased, removed
or unreadable, or warranty seal is broken.
4. The present warranty does not cover the following:
4.1. Any adaptations and alterations with the aim of
perfection and widening of the common scope of
the product application specied in the Manual.
4.2. Devices and accessories not specied in the coupon.
4.3. Damage caused in result of:
a) Improper maintenance including but not limited by following:
(1) use of the product not according to its intended purpose
or Manual;
(2) mounting and maintenance of the product in conditions not
corresponding to safety standards and regulations valid in
the country of use;
(3) incorrect software installation provided by service operator.
b) Repair performed by not authorized service centers or dealers;
c) Accidents, lightning stroke, ood, re, incorrect ventilation;
d) Transporting excluding cases when it is carried out by ASC;
e) Faults of system in which the present product had been using.
5. These warranty conditions do not intend to restrict
or limit in any way statutory rights of customers
which may not be altered in some jurisdictions
and other customers’rights which may arise out
of any agreements with third parties, provided
that nothing contained in such agreements states
or implies that the manufacturer or manufacturer
aliates assume any obligations or liabilities other
than those expressly stipulated in this Warranty
Service Coupon.
While maintaining warranty liabilities on product
repair or replacement, Manufacturer takes no
responsibilities for personal data safety, including
logins, passwords, paid or free subscriptions, settings,
portals, media les, content and software installed or
set up by Customer or other third parties.

Copyrights and Trademarks
Notice of Copyright
Telecommunication Technologies LLC. All rights
reserved. The Information contained herein is the
property of Telecommunication Technologies LLC
(the Company). Not any part hereof can be copied,
reprinted, transferred, retyped, saved in search engine,
modied or translated into any other language,
including computer one, nor sublicensed in any way,
whether electronic, mechanical, magnetic, optical,
chemical, manual or other one, without prior written
consent by the Company Manager responsible for
the Product. Any Illegal use of the materials contained
herein, by any person, will lead the person to the
responsibility for the Company’s damages.
Software Use Agreement
IMPORTANT - read carefully: when using the Software
with your device, you agree thereby with every clauses of
the Software Use Agreement. If you do not agree with the
terms and conditions of the Software Use Agreement,
you should immediately stop using the device and return
it to your services provider completely.
License provision. Limitations
According to this Agreement, Telecommunication
Technologies LLC and your services provider are
jointly to provide you with non-exclusive and
non-transferrable license, without the right to
sublicense, for use of all software and documents with
the product only. You recognize and acknowledge
that Telecommunication Technologies LLC and your
services’ provider may regularly renew, change or
extend the product software abilities. You conrm that:
a) You will not take attempts to change, extend, or
decompile, disassembly, or redesign, nor otherwise get
access to the software source code.
b) You will not take attempts to delete or upload the
product software. Any sale or transfer of the product
will be ruled hereby.
Ownership
The Manufacturer and the Manufacturer’s own licensors
keep all the rights constituting ownership, Including
patent, copyright trademark, and other Intel factual
property for the Software; and any Improvement
and modication of the Software. You recognize and
acknowledge that the license according hereof does not
grant you ownership for the Software but only restricted
right of use It according to provisions of this Agreement.
Warranty for the Software
To the maximum extent according to applicable law, the
Company does not make any submission and declines
any and all warranties, whether express or implied, as

to the Software, including, with no limitations, any
implied demand warranties, correspondence to
target destination, abuse of rights of third parties,
neither those being result of interrelations or result
of commerce.The Company does not guarantee the
Software will be free of defects or errors; that any
defects or errors will be corrected, or any function
abilities of the Software will meet all your requirements.
Warranty
Warranty for your product is supplied via your
services’ provider. In the event your product
requires maintenance service, you should contact
the services’ supplier directly.
Trademarks
Инфомир, Infomir, MAG are the trademarks of Infomir
Group. Manufactured under license from Dolby
Laboratories. Dolby, Dolby Audio, and the double-D
symbol are trademarks of Dolby Laboratories.
DCP is the trademark of Digital Content Protection LLC.
Redesigning and disassembling is illegal.
Linux® is the registered trademark of Linus Torvalds in
the U.S. and other countries.
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI Logo are
Copyrights and Trademarks
trademarks or registered trademarks of HDMI
Licensing Administrator, Inc. in the United States
and other countries.
Infomir disclaims proprietary interest in the marks
and names of others.

Terms of using
Safe and Ecient Using
Device does not contain harmful or hazardous substances.
Accessories
Use the accessories supplied with your arrangement or
recommended by the manufacturer only. Using of the
accessories which are not supplied or not sanctioned by
the manufacturer may be dangerous for the User or do
harm to the arrangement operation. Using of the not
appropriate accessories eliminates guarantees of the
product therewith.
Water and Moisture
To avoid damage that can cause ignition of the present
product or lesion to the User with electrical current, the
product and its accessories should not be undergone
with any liquids, rain or high moisture.
Do not use the present product in the places where it
may be exposed to the contact with a liquid or vapor.
Product Care
Maintenance of Product
The product should not be disassembled. The tries of
the disassembling of the product may be dangerous
for your life and for serviceability of the product.
The self-supporting disassembling invalidates you
the product guarantee.
The maintenance should be aected by qualied
specialists in the warranty processing centers only.
The product possesses protective sealing.
Breaking or changing of the mentioned sealing
invalidates guarantee of the product.
Cleaning
The product and accessories should be rubbed with
dry cloth or tissue only.
To ensure safety, before shell cleaning switch the
power supply o the alternative current socket.
The shell may be cleaned from persistent spots with
a slightly wet cloth or cleaning tissue.
Do not use cleaner or polish, benzyl, solvents,
abrasive items, liquid or aerosol detergent means for
the product and accessories cleaning.

Specications
Physical Parameters
Model: MAG420, MAG420w1
Weight: 128 g
Dimensions (approximately): 132 mm width,
87 mm depth, 26 mm height
Operation temperature and Humidity
1C - 40; 5% ~ 93%RH
Ethernet Interface
Ethernet Connector: RJ-45
Cable: UTP and STP 5 categories
Speed: Auto-choice, 10/100 Mbit/s
Indicators: Green – Activity, Yellow – Connection
Wi-Fi Interface
Built-in Wi-Fi module: b/g/n (only MAG420w1)
Operating frequency bands: 2400-2483.5 MHz
Output power (E.I.R.P.): <20 dBm (100 mW)
Internal Antenna gain: 3,38 dBi
USB Interface
Type: USB 2.0  1 pcs., USB 3.0  1 pcs.
Supported Audio-Video Formats
Video codecs: MPEG1/2 MP@HL, MPEG4 part 2 (ASP),
H.265 Main/Main [email protected] High 2160p@60 fps (optional),
H.264 AVC [email protected] 2160p@30 fps, XviD,
3D video support
Video containers:TS, AVI, MPEG, MP4, MOV, MKV, M2TS, VOB
Audio Codecs: MPEG L1/L2/L3, AAC-LC, HE AAC V1/V2,
APE, FLAC
This product supports Dolby DigitalTM
Video modes: PAL, NTSC, 576p, 720p, 1080p, 1080i, 2160p
Subtitles: DVB, PGS, SRT, SSA/ASS, SUB, Teletext subs,
WebVtt, Closed captions
Audio-Video Interfaces
Audi Connectors: TRRS (On adapter cable:
White=Left channel, Red=Right channel)
Output: 2 V RMS nominal
Loading: 10KΩ
Composite Video Interface: TRRS (Yellow connector
on adapter cable)
Output: 1Vp-p
Power supply Interface
Connector: DC cylindrical 2.1 mm x 5.5 mm
Type: plug-and-socket, DC current, center plus
Input: 12V±10%
Power consumption: less than 7.5W in typical conditions

Specications
External Power Supply Unit
Type: Pulse with universal inlet
Input: 110-240 V AC, 50-60Hz, 0.5A max
Output: 12 V DC, 1A, 12 W
Average active eciency: 83% (min)
Eciency at low load (10%): 79.54% (min)
No-load power consumption: < 0.1W
Package
Type: cardboard box.
Dimensions (approx.): 225 mm width,
95 mm depth, 60 mm height
Shipping weight: 432 g

The Product Unpacking and Installation
After the product extraction out of the package it is
necessary to handle it with care, do not drop, shake
it and aord other inuence. The product is designed
for horizontal allocation onto at surface.
Do not place the product onto slippery surface, in place
where it may be exposed to vibration or hazard to drop
and other possible risks to the product to be damaged
which may cause invalidation the product guarantee.
Do not dispose the product onto soft surface like on
the carpet, bed, etc., for such surfaces cease access to
the ventilation openings and complicate air ow that
may cause the product overheating and invalidate
guarantee in result.
Do not locate the product into the furniture in
case of vacant clearance around the product is not
provided for the sucient product ventilation.
Do not place the product in place where it may be
exposed to inuence of direct sunlight, next to the
sources of open re and convectors.
Do not dispose the product on surfaces which in
operating process may get warm, for instance, video
record player or intensier and do not put anything
on the top of the shell as well. Do not cover the
product with anything.
Containing liquids objects, such as vase, plant pot
are not to be placed next to or on the product.
Do not touch or move the product during its
operation. Switch o the product if you need
to shift it.
The product is intended for use indoors.
The power supply cord is to be put to prevent its
deformation and jamming and touching it well. The
power supply cord is not to be laid under the carpets
or blocked with anything where any damage may
not be noticed.
For AC/DC Adapter, the socket outlet must be near
the equipment and shall be easily accessible.
Power supply unit
The product should be used with power supply unit
provided by the manufacturer only.
The power supply unit is tted out with plug which
is intended for connecting to socket in your country
usage. Model: TAA0121200100HV. Manufacturer:
HUIZHOU TECHLONG CO. LTD. Address: Room
829, HONGFA CENTER BUILDING BAOAN CENTER
SHENZHEN CHINA. Commercial registration number:
91440300777167379F. In case of the necessity in the
product connecting in other country or in the region
with other data of electric circuit the power supply
unit adopted for use in the specied area should be
received from the manufacturer.

Operation
The outer power supply unit of the product is getting
warm in operation. In case of outer power supply unit
gets hot, switch o promptly and get in touch with the
equipment supplier for its replacement.
Protection from atmospheric electricity or not
using for a long time
On coming the thunderstorm and also in case of the
product is intended to be in no use for a long time,
disconnect the power supply cord out of socket,
switch o Ethernet, video and audio cables. It is to
protect the product from thunder discharges and
power surges in the circuit.
Usage with Plasma Displays
In the product usage for watching with plasma
screens do not pause the picture for more than 5
minutes, otherwise it with other objects as may cause
‘burn-out’ pixels on the screen. It is not considered
as a defect of the product but peculiarity of plasma
screens structure. The producer does not bear the
responsibility for damages had been caused in such
manner.
The Arrangement Designation
The product is intended to select digital audio & video
channels from transport streams, decode and display
them on TV. Any other use is prohibited. It means
Telecommunication Technologies LLC insists on the
product usage in entirely accordant to the law of
copyright. The compliance with the specied laws
leaves on conscience of the user. The unauthorized
copying of the protected materials or spreading of
the specied copies under denite conditions may
violate the law of copyright and is to be previously
adopted by possessor of the rights for the further
commercial use.
Updating Software
The product possesses the capability of automatic
software updating. The manufacturer and your
services provider reserve the right for automatic
software updating to improve the product functional
capability.
During the software updating the product should
not be used for watching and switched o until the
complete software updating. During the software
updating the product switching o is inadmissible.
The updating takes several minutes and since then
you are able to continue enjoy on all delights of
digital television services.

About your MAG420, MAG420w1
1. USB
2. IR-receiver
3. Indicator of stand-by mode/
Indicator of the Remote Unit
Buttons pushed
1. Power Supply
2. S/PDIF*
3. 4-pin 3,5 mm jack, Composite
video output, Stereo line output
4. HDMI
5. Ethernet LAN port
6. USB
7. Fn – Reset to factory settings/
Load from the rst U-boot/
Select alternative NAND/
“Emergency” – Load the basic
software from USB/DHCP* Optional, may not be available on your device
Front Panel
Back Panel
*

Connecting to MAG420, MAG420w1
Warning! Switch o all the devices (TV, amplier, etc.) and take the power supply unit out of the socket
before connecting or disconnecting any cable. If the amplier is not connected leave digital audio
outputs disconnected.
Connecting with HDMI – best quality
Connecting with AUDIO/VIDEO Input – good quality
* Optional, may not be available on your device
*
*
1. Red
2. White
3. Yellow

Using Remote Control to control the Device
This section explains how to unpack Remote Control
(RC) and prepare it for work. Your service provider
can supply the product with an alternative RC.
In that case please refer to the manual supplied
by your service provider. Remote Control requires
two batteries type AAA, UM-4.
Important information about using batteries.
Do not mix dierent types of battery or old and
new batteries.Do not use rechargeable batteries
with the remote control. Remove the batteries from
the remote control if you are not going to use it for
several weeks, to avoid the risk of leakage. Please
respect your environment and any local regulations and
dispose of old batteries in a responsible manner.
Caution! Do not attempt to recharge the
batteries. Immediately remove any leaking
batteries. Take care when handling leaking
batteries as they may cause burns to the skin
or eyes, or other physical injuries.
Code page alteration
The SRC-4015 remote control is designed with the ability
to switch over three dierent Infra-Red systems or Code
Pages (CP). The need to change the code page may arise
if the STB remote control interferes with other devices, a
TV for example. Initially, the RC and STB are both set to
the default CP #14
How to change the SRC-4015 code page
Step1. Changing the CP on the RC. Simultaneously press
and hold the «App» and «TV» buttons for 3+ seconds to
change the current CP to the next one. By doing this, you
can switch it to 2 alternative CPs or return to the default
CP option. For each CP option, the RC LED ashes in
dierent ways:
• First time pressing «App+TV»- the second CP option #11
is selected. The LED blinks once.
• Second time pressing «App+TV»- the third CP option #24
is selected. The LED blinks twice.
• Third time pressing «App+TV»- it returns back to the
(default) CP option #14. The LED blinks three times.
Step2. Changing the STB CP. Point the RC directly at the
STB and press the following 3 keys in the following order:
«Rewind», «Num 0», «Forward». The STB’s LED should blink
once. If you followed these instructions, the STB should
react accordingly.

Remote control SRC-4015
STB Power
Favorites
Search
APP
Menu
Back
Volume
Rewind
Play/Pause
Forward
Stop
Up
Down
Conrm
Right
Left
To select a TV channel
Keyboard
Info
Home
TV
Mute
Switch channels
Additional functions
Resize
PIP

Using Remote Control to control the Device
Introduction to the Programmable
Remote Control Unit (optional)
If MAG420, MAG420w1 package includes a remote
control with a block of ve programmable buttons
(marked with blue print colour), then you may want
to choose these buttons for controlling other devices
(TV set, amplier).
To program the buttons do the following:
• Press the «On/O» and «A/V» buttons at the same
time and hold it for 2 seconds. When the green
light of the «On/O» button will stop blinking and
willlight steadily, it means the RC is ready to learn.
• Press the button you want to «teach» — the green
light will start blinking.
• Place the infrared lamps of two RCs opposite each
other and press the button on the RC of the other
device, the function of which you wish to copy on
device RC. Hold for 2 seconds.
• After the green light two quick blinks you may
continue programming other buttons.
• Repeat the procedure described above for all
buttons you want to program for controlling
external devices.
• Press the the «On/O» and «A/V» buttons to save the
programmed data; the green light should fade o.
Reset
Press «SETUP» and «OK» buttons at same time and hold
for 2 seconds red LED will ash 5 times. Reset is done.

Turn the Media Player On / O
Change audio mode
Setup menu
TV Guide
Virtual keybord
Back
Info
Switch channels
Rewind
Fast forward
Skip backwards
Skip forward
To select a TV channel
*buttons allowed to store copied data
Programmable section*
Sound On/O*
AV*
Context menu
Quick TV access
Exit
Menu
Volume*
Play / Pause
Stop
Change aspect ratio
Update
Additionan functions
Up
Down
Conrm
Right
Left
Programmable Remote Control SRC-4513 (optional)

Product information
Product:
Serial Number:
MAC:
The set includes the following:
Set-Top Box
External Power Supply 12V
IR Remote Control
AAA batteries
Instruction manual
Package box
- 1 pcs.
- 1 pcs.
- 1 pcs.
- 2 pcs.
- 1 pcs.
- 1 pcs.
Optionally the set may include the following:
3,5 mm Jack to 3 RCA cable
LAN network cable
HDMI cable length less than 3 m
- 1 pcs.
- 1 pcs.
- 1 pcs.