Infomir MAG324 User manual

Instruction Manual
SET-TOP BOX
MAG324
MAG324w2

Set-Top Box MAG324, MAG324w2 Instruction Manual
Regulatory information
EU
This equipment has been tested and found to comply
with the essential requirements of the following
Directives: 2014/30/EU, 2014/35/EU, 2014/53/EU,
2009/125/EC, 2011/65/EU. This product is in accordance
with Directive 2012/19/EU.
The present Tlecommunication TechnologiesLLC declares
that the type of radio equipment 802.11a/b/g/n/ac
corresponds to the Technical regulations
of radio equipment. The full text of the Declaration of
Conformity is available on the website at the following
address: www.infomir.eu
This device is certied for indoor deployment only in the
5150-5350 MHz band. Do not install or use this device
outdoors in that frequency in the Europian Union.
FCC Compliance Statement
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment
and receiver.
•Connect the equipment to an outlet on a circuit
dierent from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV
technician for help.
FCC Caution:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received, including
interference that may cause undesired operation.
CAUTION:
Unauthorized antennas, modications, or attachments could
damage the device and violate FCC regulations. Changes or
modications not expressly approved by responsible party
could void the user’s authority to operate the equipment.

Set-Top Box MAG324, MAG324w2 Instruction Manual
FCC Radiation Exposure Compliance
(only for MAG324w2):
This equipment complies with radio frequency (RF)
exposure limits set forth by the Federal Communications
Commission for an uncontrolled environment. This
equipment should be installed and operated with a
minimum distance of 20 centimeters between the
radiator and your body. This transmitter must not be
co-located or operating in conjunction with any other
antenna or transmitter.
Deployment Statement (only for MAG324w2):
This device is certied for indoor deployment only in the
5150-5250 MHz band. Do not install or use this device
outdoors in that frequency in the United States.
The models MAG324w2 contains FCC ID: 2AATL-8223A-SR
Note: Specications are subject to change without
notice. Infomir reserves the right to revise this publication
and to make changes in its content from time to time by
posting new specications and other content at www.
infomir.com
Warranty term:
Europe, MEASA and Oceania:
2 years from date of sale (but not more than 2,5
years from manufacture date).
The USA, Americas, Russia, Ukraine and other
regions:
1 year from date of sale (but not more than 1,5
years from manufacture date).
See the date of manufacture at «Product
Information» section. By virtue of the present
Coupon, the absence of defects in manufacturing
of the product and its compounds is warranted for
a year-term counted since date of sale. If during the
mentioned warranty term the defects of materials
or operation of product will be found, the product
would be repaired or its defective parts would be
replaced free of charge in the warranty processing
center with compliance with warranty conditions.
WarrantyInstruction Manual

Warranty Processing Centers List:
Europe:
ZLS Services GmbH
Hamburger Allee 56. 60486, Frankfurt am Main, Germany
Tel: [phone]
e-mail: [email protected]om
The USA, Canada and Latin America:
Infomir USA
174 Bay 49th Street. Brooklyn, NY 11214 USA
Tel: [phone]
e-mail: [email protected]
Russia, Belarus:
Tel.: [phone]
e-mail: [email protected]om
MEASA and Oceania:
PROGRESSIVE TECHNOLOGY F.Z.E
Warehouse B1-40. Sheikh Rashid Bin Saeed Al Maktoum
Street
Ajman Free Zone
45573, Ajman, UAE
Tel: [phone]
e-mail: [email protected]om
Ukraine:
Telecommunication Technologies LLC
4/D, Nebesnoi Sotni Avenue. Odesa, 65121, Ukraine
Tel: [phone]
e-mail: [email protected]om
Warranty Service Coupon
(to be lled in by a shop-assistant)
Date of Sale:
Company-Seller:
Address of Company-Seller:
Place of Stamp
I have no claims as to appearance and
package contents. I accept the conditions of
warranty service.
Signature of Customer:
Manufacturer:
Telecommunication Technologies LLC
1 Mytna Square, Odessa, 65026, Ukraine
Warranty processing centersWarranty

Warranty conditions
1. The present warranty is only valid if the defective
product is provided with property lled in Warranty
Service Coupon. If date of sale is not pointed, the
warranty term is counted since date of the product
manufacturing which is dened under serial number.
Warranty processing center reserves the right to refuse
free warranty service and parts replacement in case the
mentioned above documents are not presented or the
lled in it information is not complete or unreadable.
2. The present warranty does not enable the right for
compensation and cover of loss received as a result of
rearrangement of the product.
3. The present guarantee is invalid if model or serial
number of the product is altered, erased, removed
or unreadable, or warranty seal is broken.
4. The present warranty does not cover the following:
4.1. Any adaptations and alterations with the aim of
perfection and widening of the common scope of the
product application specied in the Manual.
4.2. Devices and accessories not specied in the coupon.
4.3. Damage caused in result of:
a) Improper maintenance including but not limited by following:
(1) use of the product not according to its intended purpose
or Manual;
(2) mounting and maintenance of the product in conditions not
corresponding to safety standards and regulations valid in
the country of use;
(3) incorrect software installation provided by service operator.
b) Repair performed by not authorized service centers or dealers;
c) Accidents, lightning stroke, ood, re, incorrect ventilation;
d) Transporting excluding cases when it is carried out by ASC;
e) Faults of system in which the present product had been using.
5. These warranty conditions do not intend to restrict
or limit in any way statutory rights of customers
which may not be altered in some jurisdictions and
other customers’rights which may arise out of any
agreements with third parties, provided that nothing
contained in such agreements states or implies
that the manufacturer or manufacturer aliates
assume any obligations or liabilities other than those
expressly stipulated in this Warranty Service Coupon.
While maintaining warranty liabilities on product repair
or replacement, Manufacturer takes no responsibilities
for personal data safety, including logins, passwords,
paid or free subscriptions, settings, portals, media les,
content and software installed or set up by Customer or
other third parties.

Copyrights and Trademarks
Notice of Copyright
Telecommunication Technologies LLC. All rights
reserved. The Information contained herein is the
property of TelecommunicationTechnologies LLC (the
Company). Not any part hereof can be copied, reprinted,
transferred, retyped, saved in search engine, modied or
translated into any other language, including computer
one, nor sublicensed in any way, whether electronic,
mechanical, magnetic, optical, chemical, manual or other
one, without prior written consent by the Company
Manager responsible for the Product. Any Illegal use
of the materials contained herein, by any person, will
lead the person to the responsibility for the Company’s
damages.
Software Use Agreement
IMPORTANT - read carefully: when using the Software
with your device, you agree thereby with every
clauses of the Software Use Agreement. If you do not
agree with the terms and conditions of the Software
Use Agreement, you should immediately stop using
the device and return it to your services provider
completely.
License provision. Limitations
According to this Agreement, Telecommunication
Technologies LLC and your services provider are
jointly to provide you with non-exclusive and non-
transferrable license, without the right to sublicense, for
use of all software and documents with the product only.
You recognize and acknowledge that Telecommunication
Technologies LLC and your services’ provider may
regularly renew, change or extend the product software
abilities. You conrm that:
a) You will not take attempts to change, extend, or
decompile, disassembly, or redesign, nor otherwise get
access to the software source code.
b) You will not take attempts to delete or upload the
product software. Any sale or transfer of the product will
be ruled hereby.
Ownership
The Manufacturer and the Manufacturer’s own licensors
keep all the rights constituting ownership, Including
patent, copyright trademark, and other Intel factual
property for the Software; and any Improvement
and modication of the Software. You recognize and
acknowledge that the license according hereof does not
grant you ownership for the Software but only restricted
right of use It according to provisions of this Agreement.
Warranty for the Software
To the maximum extent according to applicable law, the
Company does not make any submission and declines
any and all warranties, whether express or implied,
as to the Software, including, with no limitations, any

implied demand warranties, correspondence to
target destination, abuse of rights of third parties,
neither those being result of interrelations or result
of commerce. The Company does not guarantee
the Software will be free of defects or errors; that
any defects or errors will be corrected, or any
function abilities of the Software will meet all your
requirements.
Warranty
Warranty for your product is supplied via your
services’ provider. In the event your product requires
maintenance service, you should contact the services’
supplier directly.
Trademarks
, Infomir, MAG are the trademarks of Infomir
Group. HDMI is the trademark of HDMI Licensing,
LLC. Manufactured under license from Dolby
Laboratories. Dolby, Dolby Audio, and the double-D
symbol are trademarks of Dolby Laboratories. DCP
is the trademark of Digital Content Protection LLC.
Redesigning and disassembling is illegal. Infomir
disclaims proprietary interest in the marks and names
of others.
Terms of usingCopyrights and Trademarks
Safe and Ecient Using
Device does not contain harmful or hazardous substances.
Accessories
Use the accessories supplied with your arrangement or
recommended by the manufacturer only. Using of the
accessories which are not supplied or not sanctioned by the
manufacturer may be dangerous for the User or do harm to
the arrangement operation. Using of the not appropriate
accessories eliminates guarantees of the product therewith.
Water and Moisture
To avoid damage that can cause ignition of the present
product or lesion to the User with electrical current, the
product and its accessories should not be undergone with
any liquids, rain or high moisture.
Do not use the present product in the places where it may
be exposed to the contact with a liquid or vapor.
Impact of Electrostatic Discharges ( ESD)
The device is exposed to ESD, which leads to IPTV set-top
box reboot, caused by the impact of ESD, and a temporary
appearance the black screen on the display during the reboot.
After a reboot an automatic restoration of the operating mode
of the IPTV set-top box is provided.
The duration of the reboot depends on the parameters of
the local network and is about 30 ... 40 seconds or more.
In such situation, the user must wait for the device to
automatically restart.

Product Care
Maintenance of Product
The product should not be disassembled. The tries of
the disassembling of the product may be dangerous for
your life and for serviceability of the product.
The self-supporting disassembling invalidates you the
product guarantee.
The maintenance should be aected by qualied
specialists in the warranty processing centers only.
The product possesses protective sealing.
Breaking or changing of the mentioned sealing
invalidates guarantee of the product.
Cleaning
The product and accessories should be rubbed with dry
cloth or tissue only.
To ensure safety, before shell cleaning switch the power
supply o the alternative current socket.
The shell may be cleaned from persistent spots with a
slightly wet cloth or cleaning tissue.
Do not use cleaner or polish, benzyl, solvents, abrasive
items, liquid or aerosol detergent means
for the product and accessories cleaning.

Specications
Physical Parameters
Model MAG324, MAG324w2
Weight: 170 g
Dimensions (approximately): 115 mm depth,
115 mm width, 28 mm height
Operation temperature and Humidity
1C - 40; 5% ~ 93%RH
Ethernet Interface
Ethernet Connector: RJ-45 shielded
Cable: UTP and STP 5 categories
Speed: Auto-choice, 10/100 Mbit/s
Indicators: Green – Activity, Yellow – Connection
Wi-Fi Interface
Built-in Wi-Fi module: 802.11 b/g/n/ac (only MAG324w2)
Operating frequency bands:
802.11 b/g/n 2400-2483.5 MHz,
802.11 a/n/ac 5150- 5825 MHz
Output power:
802.11 b/g/n <20 dBm, 802.11 a/n/ac <23 dBm
USB Interface
Type: USB2.02 pcs.
Supported Audio-Video Formats
Video odecs: MPEG-1/2, MPEG-4, H.264/AVC [email protected],
H.265/HEVC Main and Main10 prole up to 1080p at 60
fps, Xvid, 3D video supporting
Audio odecs: MPEG-1 layer I/II/III, WMA, AAC-LC,
HE-AAC v1, HE-AAC v2
This product supports Dolby DigitalTM
Video modes: 1080i, 1080p, 720p, 576p, PAL, NTSC
Subtitles: DVB, PGS, SRT, SSA/ASS, SUB,Teletext subs, WebVtt
Audio-Video Interfaces
Audi Connectors: TRRS (On adapter cable:
White=Left channel, Red=Right channel)
Output: 2 V RMS nominal, Loading: 10KΩ
Composite Video Interface, Type: TRRS
(Yellow connector on adapter cable)
Output: 1Vp-p
Power supply Interface
Connector: DC cylindrical 2.5 mm x 5.5 mm
Type: plug-and-socket, DC current, center plus
Input 12V±10%
Power Less than 7.5W in typical conditions
Outer Power Supply Unit
Type: Pulse with universal inlet
Input: 110-240 VAC, 50-60 Hz. 0,5A max
Output: 12V DC 1A
Package
Type: cardboard box
Dimensions (approx.):
57 mm height, 214 mm width, 119 mm depth
Shipping weight: 512 g

The Product Unpacking and Installation
After the product extraction out of the package it is
necessary to handle it with care, do not drop, shake
it and aord other inuence. The product is designed
for horizontal allocation onto at surface.
Do not place the product onto slippery surface, in place
where it may be exposed to vibration or hazard to drop
and other possible risks to the product to be damaged
which may cause invalidation the product guarantee.
Do not dispose the product onto soft surface like on
the carpet, bed, etc., for such surfaces cease access to
the ventilation openings and complicate air ow that
may cause the product overheating and invalidate
guarantee in result.
Do not locate the product into the furniture in
case of vacant clearance around the product is not
provided for the sucient product ventilation.
Do not place the product in place where it may be
exposed to inuence of direct sunlight, next to the
sources of open re and convectors.
Do not dispose the product on surfaces which in
operating process may get warm, for instance, video
record player or intensier and do not put anything
on the top of the shell as well. Do not cover the
product with anything.
Containing liquids objects, such as vase, plant pot
are not to be placed next to or on the product. Do
not touch or move the product during its operation.
Switch o the product if you need to shift it.
The product is intended for use indoors.
The power supply cord is to be put to prevent its
deformation and jamming and touching it well. The
power supply cord is not to be laid under the carpets
or blocked with anything where any damage may
not be noticed.
For AC/DC Adapter, the socket outlet must be near
the equipment and shall be easily accessible.
Power supply unit
The product should be used with power supply unit
provided by the manufacturer only.
The power supply unit is tted out with plug which
is intended for connecting to socket in your country
usage. In case of the necessity in the product
connecting in other country or in the region with
other data of electric circuit the power supply unit
adopted for use in the specied area should be
received from the manufacturer.
Operation
The outer power supply unit of the product is getting
warm in operation. In case of outer power supply unit
gets hot, switch o promptly and get in touch with the
equipment supplier for its replacement.

Protection from atmospheric electricity or not
using for a long time
On coming the thunderstorm and also in case of the
product is intended to be in no use for a long time,
disconnect the power supply cord out of socket,
switch o Ethernet, video and audio cables. It is to
protect the product from thunder discharges and
power surges in the circuit.
Usage with Plasma Displays
In the product usage for watching with plasma
screens do not pause the picture for more than 5
minutes, otherwise it with other objects as may cause
‘burn-out’ pixels on the screen. It is not considered
as a defect of the product but peculiarity of plasma
screens structure. The producer does not bear the
responsibility for damages had been caused in such
manner.
The Arrangement Designation
The product is intended to select digital audio &
video channels from transport streams, decode and
display them on TV. Any other use is prohibited. It
means Telecommunication Technologies LLC insists
on the product usage in entirely accordant to the law
of copyright. The compliance with the specied laws
leaves on conscience of the user. The unauthorized
copying of the protected materials or spreading of
the specied copies under denite conditions may
violate the law of copyright and is to be previously
adopted by possessor of the rights for the further
commercial use.
Updating Software
The product possesses the capability of automatic
software updating. The manufacturer and your
services provider reserve the right for automatic
software updating to improve the product functional
capability.
During the software updating the product should
not be used for watching and switched o until the
complete software updating. During the software
updating the product switching o is inadmissible.
The updating takes several minutes and since then
you are able to continue enjoy on all delights of
digital television services.

1. Fn - Reset to factory settings/
select the boot mode
2. USB 2.0
3. LED
4. Power On/O
1. Power Supply
2. RCA 3,5 mm jack
3. HDMI
4. Ethernet
Front Panel
Back Panel
About your MAG324, MAG324w2

Warning! Switch o all the devices(TV, amplier, etc.) and take the power supply unit out of the socket
before connecting or disconnecting any cable. If the amplier is not connected leave digital audio outputs
disconnected.
Connecting with HDMI – best quality
Connecting with AUDIO/VIDEO Input – good quality
1. Red
2. White
3. Yellow
Connecting to MAG324, MAG324w2

Using Remote Control to control the Device
This section explains how to unpack Remote Control
(RC) and prepare it for work. Your service provider can
supply the product with an alternative RC. In that case
please refer to the manual supplied by your service
provider. Remote Control requires two batteries type
AAA, R03, LR03, UM-4, 286. Important information about
using batteries. Do not mix dierent types of battery or
old and new batteries.Do not use rechargeable batteries
with the remote control. Remove the batteries from the
remote control if you are not going to use it for several
weeks, to avoid the risk of leakage. Please respect your
environment and any local regulations and dispose of
old batteries in a responsible manner.
Caution! Do not attempt to recharge the
batteries.Immediately remove any leaking
batteries. Take care when handling leaking
batteries as they may cause burns to the skin
or eyes, or other physical injuries.
Introduction to the Programmable
Remote Control Unit (optional)
The MAG324, MAG324w2 package includes a remote
control with a block of ve programmable buttons
(marked with blue print colour). You may want to choose
these buttons for controlling other devices (your TV set or
amplier). To program the buttons, do the following:
• Place infrared LEDs of both Remote Controls (STB RC and TV
RC) opposite each other at a maximum distance of 5 cm.
• On the STB RC, press the‘Red’and ‘Blue’buttons of
‘Additional functions’at the same time and hold them
together for 3 seconds. Access to the setup is conrmed
when the visual LEDs under‘TV power’ button (Green) and
‘STB power’ button (Red) turn ON and remain ON.
• On the STB RC, press the button that will store the copied
data, the LED under‘STB power’ button will blink once and
remains ON, to indicate selection of allowed button.
• On the TV RC, press the button, whose function you wish to
copy to the STB remote. Hold the button until the LED under
the‘TV Power’button (Green) on STB RC blinks twice to
indicate successful operation. Both visual LEDs remain ON.
• The STB R will continue in the copying setup mode and
will wait for the user’s input to other STB remote buttons
according to steps 3 and 4.
• To nish the copying process, press the‘OK’ button on the
STB RC. Both LEDs will double blink and turn OFF.
Reset
Make sure RC is in idle mode (no IR-transmission or visual
activity). Press‘SETUP’and ‘OK’buttons at the same time and
hold up (about 2 seconds) until the visual LEDs under‘TV
Power’button (Green) and‘STB Power’button (Red) turn ON.
Then, release both pressed buttons – the LEDs will turn OFF
in 1 second. Reset is done.

RCU
Home
TV Power*
Quick access to‘IPTV
channels’ section
Mute*
A/VTV
TV
APP
789
456
123
0
PIP
OK
EPG
AV*
V P
STB Power
Refresh
Rewing
Electronic Program
Guide
Fast Forward
Keyboard
TV
V
APP
OK
EPG
P
PIP
Resize
Volume*
* buttons allowed to store copied data

Product information
Product:
Serial Number:
MAC:
The set includes the following:
Set-Top Box
External Power Supply 12V
IR Remote Control
AAA batteries
Instruction manual
Package box
- 1 pcs.
- 1 pcs.
- 1 pcs.
- 2 pcs.
- 1 pcs.
- 1 pcs.
Optionally the set may include the following:
3,5 mm Jack to 3 RCA cable
LAN network cable
HDMI cable length less than 3 m
- 1 pcs.
- 1 pcs.
- 1 pcs.