Infomir MAG520 User manual

Instruction Manual
Linux based
Set-Top Box
MAG520
MAG520w3

Regulatory information
UK
This equipment has been tested and found to comply with
the essential requirements of the following Regulations: The
Radio Equipment Regulations 2017, The Electrical Equipment
(Safety) Regulations 2016, Electromagnetic Compatibility
Regulations 2016. This product is in accordance with The
Waste Electrical and Electronic Equipment Regulations 2013.
Hereby, Telecommunication Technology LLC declares that
MAG520w3 with the radio equipment type 802.11a/b/g/n/ac
is in compliance with the Radio Equipment Regulations 2017.
The full text of the declaration of conformity is available at the
following internet address:
www.infomir.eu/eng/support/declarations
This device is certied for indoor deployment only in the
5150-5350 MHz band. Do not install or use this device
outdoors in that frequency in the UK.
EU
This equipment has been tested and found to comply with the
essential requirements of the following Directives: 2014/30/
EU, 2014/35/EU, 2014/53/EU, 2009/125/EC, 2011/65/EU. This
product is in accordance with Directive WEEE 2012/19/EU.
Hereby, Telecommunication Technology LLC declares that
MAG520w3 with the radio equipment type 802.11a/b/g/n/ac
is in compliance with the 2014/53/EU Directive. The full text of
the EU declaration of conformity is available at the following
internet address: www.infomir.eu/eng/support/declarations
This device is certied for indoor deployment only in the
5150–5350MHz band. Do not install or use this device
outdoors in that frequency in the European Union.
FCC
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules.These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a residential installation.This equipment generates,
uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause
harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment to an outlet on a circuit dierent
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
FCC Caution:
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received, including
interference that may cause undesired operation.

Warranty term:
Europe, MEASA and Oceania:
2years from date of sale (but not more than 2,5years from
manufacture date).
The USA, Americas, Russia, Ukraine and other regions:
1year from date of sale (but not more than 1,5years from
manufacture date).
See the date of manufacture at «Product Information» section.
By virtue of the present Coupon, the absence ofdefects
in manufacturing of the product and its compounds is
warranted for a year-term counted since date of sale. Ifduring
the mentioned warranty term the defects of materials or
operation of product will be found, the product would be
repaired or its defective parts would be replaced free of
charge in the warranty processing center with compliance
with warranty conditions.
Warranty
CAUTION:
Unauthorized antennas, modications, or attachments could
damage the device and violate FCC regulations. Changes or
modications not expressly approved by responsible party
could void the user’s authority to operate the equipment.
FCC Radiation Exposure Compliance
(only for MAG520w3):
This equipment complies with radio frequency (RF) exposure
limits set forth by the Federal Communications Commission
for an uncontrolled environment. This equipment should
be installed and operated with a minimum distance of
20 centimeters between the radiator and your body.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
This device is certied for indoor deployment only in the
5150–5250MHz band. Do not install or use this device
outdoors in that frequency in the United States.

Warranty processing centers
Europe:
ZLS Services GmbH
Hamburger Allee 56
60486, Frankfurt am Main, Germany
Tel.: [phone]
e-mail: [email protected]om
The USA, Canada and Latin America:
Infomir USA
174 Bay 49th Street
Brooklyn, NY 11214 USA
Tel: [phone]
e-mail: [email protected]
Russia, Belarus:
Tel.: [phone]
e-mail: [email protected]om
MEASA and Oceania:
PROGRESSIVE TECHNOLOGY F.Z.E
Warehouse B1-40
Sheikh Rashid Bin Saeed Al Maktoum Street
Ajman Free Zone, 45573, Ajman, UAE
Tel: [phone]
e-mail: [email protected]om
Ukraine:
Telecommunication Technologies LLC
4/D, Nebesnoi Sotni Avenue
Odesa, 65121, Ukraine
Tel: [phone]
e-mail: [email protected]om
Warranty
Warranty Service Coupon
(to be lled in by a shop-assistant)
Date of Sale:
Seller:
Address of Seller:
Place of Stamp
I have no claims as to appearance and
package contents. I accept the warranty
conditions.
Signature of Customer:
Manufacturer:
Telecommunication Technologies LLC,
1 Mytna Square, Odesa, 65026, Ukraine

Warranty conditions
1. The present warranty is only valid if the defective product
is provided with property lled in Warranty Service
Coupon. If date of sale is not pointed, the warranty term is
counted since date of the product manufacturing which is
dened under serial number. Warranty processing center
reserves the right to refuse free warranty service and parts
replacement in case the mentioned above documents are
not presented or the lled in it information is not complete
or unreadable.
2. The present warranty does not enable the right for
compensation and cover of loss received as a result of
rearrangement of the product.
3. The present warranty is invalid if model or serial number of
the product is altered, erased, removed or unreadable, or
warranty seal is broken.
4. The present warranty does not cover the following:
4.1. Any adaptations and alterations with the aim of perfection
and widening of the common scope of the product
application specied in the Manual.
4.2. Devices and accessories not specied in the“Product
Information”section.
4.3. The batteries for the remote control included with the Set-
Top Box.
4.4. Damage caused in result of:
a) Improper maintenance including but not limited by following:
(1) use of the product not according to its intended purpose or Manual;
(2) mounting and maintenance of the product in conditions not
corresponding to safety standards and regulations valid in
the country of use;
(3) incorrect software installation provided by service operator.
b) Repair performed by not authorized service centers or dealers;
c) Accidents, lightning stroke, ood, re, incorrect ventilation;
d) Transporting excluding cases when it is carried out by warranty
processing centers;
e) Faults of system in which the present product had been using.
5. These warranty conditions do not intend to restrict or limit
in any way statutory rights of customers which may not be
altered in some jurisdictions and other customers’rights
which may arise out of any agreements with third parties,
provided that nothing contained in such agreements states
or implies that the manufacturer or manufacturer aliates
assume any obligations or liabilities other than those
expressly stipulated in this Warranty Service Coupon.
While maintaining warranty liabilities on product repair
or replacement, Manufacturer takes no responsibilities for
personal data safety, including logins, passwords, paid or
free subscriptions, settings, portals, media les, content and
software installed or set up by Customer or other third parties.

Copyrights and Trademarks
Notice of Copyright
Telecommunication Technologies LLC. All rights reserved.
The Information contained herein is the property of
Telecommunication TechnologiesLLC (the Company). Not
any part hereof can be copied, reprinted, transferred, retyped,
saved in search engine, modied or translated into any other
language, including computer one, nor sublicensed in any
way, whether electronic, mechanical, magnetic, optical,
chemical, manual or other one, without prior written consent
by the Company Manager responsible for the Product. Any
Illegal use of the materials contained herein, by any person,
will lead the person to the responsibility for the Company’s
damages.
Software Use Agreement
IMPORTANT: READ CAREFULLY: WHEN USING THE SOFTWARE WITH
YOUR DEVICE, YOU AGREE THEREBY WITH EVERY CLAUSES OF THE
SOFTWARE USE AGREEMENT. IF YOU DO NOT AGREE WITH THE
TERMS AND CONDITIONS OF THE SOFTWARE USE AGREEMENT, YOU
SHOULD IMMEDIATELY STOP USING THE DEVICE AND RETURN IT TO
YOUR SERVICES PROVIDER COMPLETELY.
License provision. Limitations
According to this Agreement, Telecommunication
Technologies LLC and your services provider are jointly
to provide you with non-exclusive and non- transferrable
license, without the right to sublicense, for use of all software
and documents with the product only.You recognize and
acknowledge that Telecommunication Technologies LLC and
your services’provider may regularly renew, change or extend
the product software abilities. You conrm that:
a) You will not take attempts to change, extend, or decompile,
disassembly, or redesign, nor otherwise get access to the
software source code.
b) You will not take attempts to delete or upload the product
software. Any sale or transfer of the product will be ruled
hereby.
Ownership
The Manufacturer and the Manufacturer’s own licensors
keep all the rights constituting ownership, including patent,
copyright trademark, and other intellectual property for
the Software; and any improvement and modication of
the Software. You recognize and acknowledge that the
license according hereof does not grant you ownership for
the Software but only restricted right of use It according to
provisions of this Agreement.
Warranty for the Software
To the maximum extent according to applicable law, the
Company does not make any submission and declines
any and all warranties, whether express or implied, as to
the Software, including, with no limitations, any implied
demand warranties, correspondence to target destination,
abuse of rights of third parties, neither those being result of
interrelations or result of commerce. The Company does not
guarantee the Software will be free of defects or errors; that
any defects or errors will be corrected, or any function abilities
of the Software will meet all your requirements.

Copyrights and Trademarks
Trademarks
Инфомир, Infomir, MAG are the trademarks of Infomir Group.
The terms HDMI and HDMI High-Denition Multimedia
Interface, and the HDMI Logo are trademarks or registered
trademarks of HDMI Licensing Administrator, Inc. in the United
States and other countries. Manufactured under license from
Dolby Laboratories. Dolby, Dolby Audio, and the double-D
symbol are trademarks of Dolby Laboratories. Linux® is the
registered trademark of Linus Torvalds in the U.S. and other
countries. Infomir disclaims proprietary interest in the marks
and names of others.
Terms of using
Safe and Ecient Using
Device does not contain harmful or hazardous substances.
Accessories
Use the accessories supplied with your arrangement or
recommended by the manufacturer only. Using of the
accessories which are not supplied or not sanctioned by the
manufacturer may be dangerous for the User or do harm to
the arrangement operation. Using of the not appropriate
accessories eliminates guarantees of the product therewith.
Water and Moisture
To avoid damage that can cause ignition of the present
product or lesion to the User with electrical current, the
product and its accessories should not be undergone with any
liquids, rain or high moisture. Do not use the present product
in the places where it may be exposed to the contact with
aliquid or vapor.

The Product Unpacking and Installation
After the product extraction out of the package it is necessary
to handle it with care, do not drop, shake it and aord other
inuence. The product is designed for horizontal allocation
onto at surface. The product is intended for use indoors.
• Do not place the product onto slippery surface, in place
where it may be exposed to vibration or hazard to drop and
other possible risks to the product to be damaged which
may cause invalidation the product warranty.
• Do not leave the product on soft surfaces such as rugs,
beds, etc. The absence of an air gap between the body of
the set-top box and the surface can lead to overheating and
void the warranty.
• Do not locate the product into the furniture in case of
vacant clearance around the product is not provided for the
sucient product ventilation.
• Do not place the product in place where it may be exposed
to inuence of direct sunlight, next to the sources of open
re and convectors.
• Do not dispose the product on surfaces which in operating
process may get warm, for instance, video record player
or intensier and do not put anything on the top of the
shell as well.
• Do not cover the product with anything.
• Containing liquids objects, such as vase, plant pot are not to
be placed next to or on the product.
• Do not touch or move the product during its operation.
• Switch o the product if you need to shift it.
The power supply cord is to be put to prevent its deformation
and jamming and touching it well. The power supply cord
is not to be laid under the carpets or blocked with anything
where any damage may not be noticed.
Power supply unit
The product should be used with power supply unit provided
by the manufacturer only. The power supply unit is tted
out with plug which is intended for connecting to socket in
your country usage. In case of the necessity in the product
connecting in other country or in the region with other data
of electric circuit the power supply unit adopted for use in
the specied area should be received from the manufacturer.
ForAC/DC Adapter, the socket outlet must be near the
equipment and shall be easily accessible.
Operation
The outer power supply unit of the product is getting warm in
operation. In case of outer power supply unit gets hot, switch
o promptly and get in touch with the equipment supplier for
its replacement.
Protection from atmospheric electricity or not using
for a long time
On coming the thunderstorm and also in case of the product
is intended to be in no use for a long time, disconnect the
power supply cord out of socket, switch o Ethernet, video
and audio cables. It is to protect the product from thunder
discharges and power surges in the circuit.
Usage with Plasma Displays
In the product usage for watching with plasma screens do not
pause the picture for more than 5 minutes, otherwise it with

other objects as may cause ‘burn-out’ pixels on the screen. It
is not considered as a defect of the product but peculiarity
of plasma screens structure. The producer does not bear the
responsibility for damages had been caused in such manner.
The Arrangement Designation
The product is intended to select digital audio & video
channels from transport streams, decode and display them on
TV. Any other use is prohibited. It means Telecommunication
Technologies LLC insists on the product usage in entirely
accordant to the law of copyright. The compliance with
the specied laws leaves on conscience of the user. The
unauthorized copying of the protected materials or spreading
of the specied copies under denite conditions may violate
the law of copyright and is to be previously adopted by
possessor of the rights for the further commercial use.
Updating Software
The product possesses the capability of automatic software
updating. The manufacturer and your services provider
reserve the right for automatic software updating to improve
the product functional capability. During the software
updating the product should not be used for watching and
switched o until the complete software updating. During the
software updating the product switching o is inadmissible.
The updating takes several minutes and since then you are
able to continue enjoy on all delights of digital television
services.
Product Care
Maintenance of Product
The product should not be disassembled. The tries of the
disassembling of the product may be dangerous for your
life and for serviceability of the product. The self-supporting
disassembling invalidates you the product guarantee. The
maintenance should be aected by qualied specialists in
the warranty processing centers only. The product possesses
protective sealing. Breaking or changing of the mentioned
sealing invalidates guarantee of the product.
Cleaning
The product and accessories should be rubbed with dry cloth
or tissue only. To ensure safety, before shell cleaning switch
the power supply o the alternative current socket. The shell
may be cleaned from persistent spots with a slightly wet
cloth or cleaning tissue. Do not use cleaner or polish, benzyl,
solvents, abrasive items, liquid or aerosol detergent means for
the product and accessories cleaning.

Specications
Physical Parameters
Model: MAG520, MAG520w3
Weight: 110 g (3,88 oz). Dimensions (approximately): 78 mm
(3.07’’) depth, 120 mm (4,72’’) width, 21 mm (0.83’’) height
Operation temperature and Humidity
1°C - 40°С (33,8 F - 104 F); 5% ~ 93%RH
Ethernet Interface
Ethernet Connector: RJ-45
Cable: UTP and STP 5 categories
Speed: Auto-choice, 10/100 Mbit/s
Indicators: Green – Activity, Yellow – Connection
Wi-Fi Interface
Built-in Wi-Fi module: 2T2R ac (only MAG520w3)
Operating frequency bands:
802.11 b/g/n 2400 MHz ~ 2497 MHz,
802.11 a/n/ac 4900 MHz ~ 5845 MHz
Output power (E.I.R.P.):
IEEE 802.11 a/b/g/n/ac <20 dBm (100mW)
Internal Antenna gain (max): 3,11 dBi (5GHz), 2,69 dBi (2.4GHz)
HDMI Interface
Type: HDMI 2.1
USB Interface
Type: USB 2.0 х 1 pcs., USB 3.0 х 1 pcs.
Supported Audio-Video Formats
Video codecs: MPEG1/2 MP@HL, MPEG4 part 2 (ASP), H.265
Main/Main [email protected] High 2160p@60 fps (optional),
H.264 AVC H[email protected] 2160p@30 fps, XviD, 3D video support
Video containers: TS, AVI, MPEG, MP4, MOV, MKV, M2TS, VOB
Audio Codecs: MPEG L1/L2/L3, AAC-LC, HE AAC V1/V2, APE, FLAC
This product supports Dolby Digital PlusTM
Video modes: PAL, NTSC, 576p, 720p, 1080p, 1080i, 4K
Subtitles: DVB, PGS, SRT, SSA/ASS, SUB, Teletext subs, WebVtt,
Closed captions
Power supply Interface
Connector: DC cylindrical 1.35 mm x 3.5 mm
Type: center plus
Input: 5 V
Power Consumption: max 5W in typical conditions
External Power Supply Unit
Type: Pulse with universal inlet
Input: 90-264 V AC, 50-60Hz, 0.4A max
Output: 5 V DC, 2A, 10W
Package
Type: cardboard box.
Dimensions (approx.): 225 mm (8.86‘’) width, 95 mm (3.74’’)
depth, 60 mm (2.36’’) height
Shipping weight: 432 g (15.24 oz)
NOTE: SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
INFOMIR RESERVES THE RIGHT TO REVISE THIS PUBLICATION AND TO
MAKE CHANGES IN ITS CONTENT FROM TIME TO TIME BY POSTING
NEW SPECIFICATIONS AND OTHER CONTENT AT WWW.INFOMIR.EU

Step 1
Connect HDMI Cable
Step 2
Connect Power Supply Unit
Step 3
Connect to the Internet
(via Ethernet or Wi-Fi *)
Connecting to MAG520, MAG520w3
WARNING! SWITCH OFF ALL THE DEVICES (TV, AMPLIFIER, ETC.)
AND TAKE THE POWER SUPPLY UNIT OUT OF THE SOCKET BEFORE
CONNECTING OR DISCONNECTING ANY CABLE.
* ONLY IN MAG520W3
About your MAG520, MAG520w3
1. USB 2.0
2. USB 3.0
4. Fn – Reset to factory settings/ Load from the rst U-boot/
“Emergency” – Load the basic software from USB/DHCP
1. Power Supply 5V 2. HDMI 2.1 3. Ethernet LAN
port
Front Panel
Back Panel

Using Remote Control to control the Device
Remote Control SRC-4015
This section explains how to unpack Remote Control (RC)
and prepare it for work. Your service provider can supply the
product with an alternative RC. In that case please refer to the
manual supplied by your service provider. Remote Control
requires two batteries type AAA, UM-4.
Code page alteration
The SRC-4015 remote control is designed with the ability to
switch over three dierent Infra-Red systems or Code Pages
(CP). The need to change the code page may arise if the STB
remote control interferes with other devices, a TV for example.
Initially, the RC and STB are both set to the default CP #14.
How to change the SRC-4015 code page
Step1
Changing the CP on the RC. Simultaneously press and hold
the «App» and «TV» buttons for 3+ seconds to change
the current CP to the next one. By doing this, you can switch it
to 2 alternative CPs or return to the default CP option. For each
CP option, the RC LED ashes in dierent ways:
• First time pressing «App+TV» - the second CP option #11 is
selected. The LED blinks once.
• Second time pressing «App+TV» - the third CP option #24 is
selected. The LED blinks twice.
• Third time pressing «App+TV» - it returns back to the
(default) CP option #14. The LED blinks three times.
Step2
Changing the STB CP. Point the RC directly at the STB and
press the following 3 keys in the following order:
«Rewind» , «Num 0» , «Forward» . The STB’s LED
should blink once. If you followed these instructions, the STB
should react accordingly.
Important information about using batteries
Do not mix dierent types of battery or old and new batteries.
Do not use rechargeable batteries with the remote control.
Remove the batteries from the remote control if you are not
going to use it for several weeks, to avoid the risk of leakage.
Please respect your environment and any local regulations
and dispose of old batteries in a responsible manner.
CAUTION! DO NOT ATTEMPT TO RECHARGE THE BATTERIES.
IMMEDIATELY REMOVE ANY LEAKING BATTERIES. TAKE CARE WHEN
HANDLING LEAKING BATTERIES AS THEY MAY CAUSE BURNS TO THE
SKIN OR EYES, OR OTHER PHYSICAL INJURIES.

Remote control SRC-4015
STB Power
Favorites
Search
APP
Menu
Back
Volume
Rewind
Play/Pause
Forward
Stop
Up
Down
Conrm
Right
Left
To select a TV channel
Keyboard
Info
Home
TV
Mute
Switch channels
Additional functions
Resize
PIP

Using Remote Control to control the Device
Introduction to the Programmable Remote Control
Unit (optional)
If MAG520, MAG520w3 package includes a remote control
with a block of ve programmable buttons (marked with blue
print colour), then you may want to choose these buttons for
controlling other devices (TV set, amplier).
To program the buttons do the following:
1. Press the «On/O» and «A/V» buttons at the same
time and hold it for 2 seconds. When the green light of
the «On/O» button will stop blinking and will light
steadily, it means the RC is ready to learn.
2. Press the button you want to «teach» — the green light will
start blinking.
3. Place the infrared lamps of two RCs opposite each other and
press the button on the RC of the other device, the function
of which you wish to copy on device RC. Hold for 2 seconds.
4. After the green light two quick blinks you may continue
programming other buttons.
5. Repeat the procedure described above for all buttons you
want to program for controlling external devices.
6. Press the the «On/O» and «A/V» buttons to save
the programmed data; the green light should fade o.
Reset
Press «SETUP» and «OK» buttons at same time and
hold for 2seconds red LED will ash 5 times. Reset is done.

Turn the Media Player On/O
Change audio mode
Setup menu
TV Guide
Virtual keyboard
Back
Info
Switch channels
Rewind
Fast forward
Skip backwards
Skip forward
To select a TV channel
*BUTTONS ALLOWED TO STORE COPIED DATA
Programmable section*
Sound On/O*
A/V*
Context menu
Quick TV access
Exit
Menu
Volume*
Play / Pause
Stop
Change aspect ratio
Update
Additional functions
Up
Down
Conrm
Right
Left
Programmable Remote Control SRC-4513 (optional)

Product information
Product:
Serial Number:
MAC:
The set includes the following:
Set-Top Box
External Power Supply 5V
IR Remote Control
AAA batteries
Instruction manual
Package box
- 1 pcs.
- 1 pcs.
- 1 pcs.
- 2 pcs.
- 1 pcs.
- 1 pcs.
Optionally the set may include the following:
HDMI cable length less than 3 m
LAN network cable
- 1 pcs.
- 1 pcs.