Ingenico AXIUM DX8000-BASE-C User manual

AXIUM DX8000-BASE-C
User Guide
www.ingenico.com
13-17 rue Pagès, 92150 Suresnes – France
Banks and Acquirers International Holding, SAS / 814 767 216 RCS Nanterre
UYS01000524

2
Table of Contents
1. Product Introduction
1.1 What’s in the Box – subject to ordered product configuration
1.2 Device Layout
2. Product Specifications
2.1 Product Functions
2.2 Product Technology Specifications
2.3 Environmental Conditions
3. Product Installation Instructions
3.1 Installing the DX8000 and Base
3.2 Fixing of the base
4. Standards and Operating Information
4.1 Delivery and Storage
4.2 Power Adapter
4.3 Standards
THE PRODUCT
Contents
2
3
3
3
4
4
4
4
5
5
6
7
7
7
7
8
10/31
AXIUM DX8000-BASE-C Copyright© 2022 Ingenico –
Banks and Acquirers International Holding SAS
All rights reserved

1. Product Introduction
1.1 What’s in the Box – subject to ordered product configuration
Procedures：
1) Open the package
2) Check the following items(Subject to actual product configuration)
Base host
Product instruction
USB Type-C cable
5V 2A Power adapter
3) Inspect the terminal and accessories and remove any shipping tape or packaging items.
1.2 Device Layout
1. USB-TYPE C Power Interface 2. DX8000 Charging Contact
3
10/31
AXIUM DX8000-BASE-C Copyright© 2022 Ingenico –
Banks and Acquirers International Holding SAS
All rights reserved

2. Product Specifications
2.1 Product Functions
The base is designed to charge DX8000 terminals.
With an optional mount, the base can be used to fix the DX8000 to a counter or
other structure.
2.2 Product Technology Specifications
2.3 Environmental Conditions
Environmental conditions for running, storing and delivering the product：
Port
Power adapter
Size and Weight
• a USB type-C power port
• input 100-240V AC, 50/60Hz
• output 5.0V 2.0A DC
• Size：193.8mm x 89mm x 38.6mm / 7.63 in x 3.5 in x 1.5 in
• Net Weight：0.18kg
• Gross Weight：0.33kg
• 0℃～40℃ / 32°F ~ 104°F
• -20℃～70℃ / -4°F ~ 158°F
• 10％～90％
• 5％～90％（40℃）/ (104°F)
• 86kPa～106 kPa
• Below 2000 meters above sea level
Temperature
Humidity
Atmospheric pressure
Running
Storage and
Delivery
Running
Storage and
Delivery
4
10/31
AXIUM DX8000-BASE-C Copyright© 2022 Ingenico –
Banks and Acquirers International Holding SAS
All rights reserved

3. Product Installation Instructions
3.1 Installing the DX8000 and Base
Installation procedures as below:
Remove all packaging and tape used for shipping purposes.
Please base onto location where it will be used.
Connect power adapter to back of base and plug it into an appropriate power plug
Set the DX8000 terminal on top of the base.
Watch for charging indicator to ensure that the base it properly connected and
working.
5
10/31
AXIUM DX8000-BASE-C Copyright© 2022 Ingenico –
Banks and Acquirers International Holding SAS
All rights reserved

3.2 Fixing of the base
In some scenes, we want to fix the base and the DX8000 to the table. An optional mounting kit
is available for this purpose.
Installation procedures as below:
Mount the space block on the table with screws.
Fasten the Base structure on the space block with three screws.
Put the base on the structure to lock it.
Fasten the Base Fixing structure on the base with three screws.
Replace the battery cover of DX8000 and put DX8000 on the base to lock it.
If removal of the base and DX8000 is required, use screwdriver to push the area of
the structure to unfix them.
6
10/31
AXIUM DX8000-BASE-C Copyright© 2022 Ingenico –
Banks and Acquirers International Holding SAS
All rights reserved

4. Standards and Operating Information
Prevent the terminal from sun exposure, high temperature, moister and other mean conditions.
Cut off the power before cleaning the device and wipe the main body with dry cloth.
When the following abnormal phenomena occur, stop running the device immediately, cut off
the power supply, and report to the service provider as soon as possible:
harsh noise heard during operation.
impurities or water found in the machine.
Unpleasant smell found during operation.
4.1 Delivery and Storage
Deliver the device in normal way, avoiding rain and snow, sun exposure and mechanical impact.
The product should be stored in the original box. The box should be at least 15cm away from the
floor, at least 50cm from the wall, heat source, cold source, window or air inlet.
4.2 Power Adapter
The base can only be connected to the adapter which is provided with DX8000. Other power
adapters may damage the base on DX unit.
WARNING
The power adapter provided is specially designed for Ingenico DX8000-BASE-C. Do not use
any other power supply. The use of a power supply with apparently similar voltage/current
characteristics may damage your terminal.
RF exposure
The antenna of the product, under normal use conditions, should be kept at least 20cm
away from the body of the user. Warning statement to the user for keeping 20cm
separation distance and the prohibition of operating to a person has been printed on the user
manual. So, this product under normal use is l0cated on electromagnetic far field between the
human body.
4.3 Standards
CE Marking
The CE marking indicates DX8000-BASE-C complies with the requirements of European
Directive2014/53/EU on Radio equipment for the protection of the health and the safety of the
user and any other person.
The protection requirements with respect to electromagnetic compatibility. And complies
with harmonized standards.
Environment (WEEE, Batteries and packaging)
This product is labeled in accordance with European Directives 2012/19/EU concerning Waste
Electrical and Electronic Equipment (WEEE) and 2013/56/EC concerning Batteries and
Accumulators. Those provisions are requiring producers and manufacturers to become
liable for take-back, treatment and recycling upon end of life of equipment and batteries.
7
10/31
AXIUM DX8000-BASE-C Copyright© 2022 Ingenico –
Banks and Acquirers International Holding SAS
All rights reserved

The crossed-out waste bin stuck on the product or its accessories means that the
product belongs to the family of electrical and electronic equipment, and waste
batteries must not be thrown away but collected separately and recycles.
Please contact your retailers for more detailed information about the compliance
solution in place for disposing of your old productand used batteries.
THE PRODUCT
Packaging waste must also be collected separately to assure a proper disposal and recycling.
In this way you can participate in the re-use and upgrading of Electrical and Electronic Equipment
Waste, which can have an effect on the environment and human health.
It stands for DC Voltage.
This Document is Copyright © 2022 by Ingenico Group. Ingenico retains full copyright
ownership, rights and protection in all material contained in this document. The recipient can
receive this document on the condition that he will keep the document confidential and will
not use its contents in any form or by any means, except as agreed beforehand, without
the prior written permission of Ingenico. Moreover, nobody is authorized to place this
document at the disposal of any third party without the prior written permission of Ingenico.
If such permission is granted, it will be subject to the condition that the recipient ensures that
any other recipient of this document, or information contained therein, is held responsible to
Ingenico for the confidentiality of that information.
Care has been taken to ensure that the content of this document is as accurate as
possible. Ingenico however declines any responsibility for inaccurate, incomplete or outdated
information. The contents of this document may change from time to time without prior
notice, and do not create, specify, modify or replace any new or prior contractual obligations
agreed upon in writing between Ingenico and the user.
Ingenico is not responsible for any use of this device, which would be non-consistent with the
present document.
All trademarks used in this document remain the property of their rightful owners.
8
10/31
AXIUM DX8000-BASE-C Copyright© 2022 Ingenico –
Banks and Acquirers International Holding SAS
All rights reserved
www.ingenico.com
13-17 rue Pagès, 92150 Suresnes – France
Banks and Acquirers International Holding, SAS / 814 767 216 RCS Nanterre