Ingersoll-Rand 650484-X User manual

E2011
(800) 495--0276 DFAX (800) 892--6276
INGERSOLL RAND COMPANY
209 NORTH MAIN STREET -- BRYAN, OHIO 43506
OPERATOR’S MANUAL 650484-X
RELEASED: 1-5-96
REVISED: 6-1-10
(REV. D)
TWO BALL PUMP SERIES
4-1/4” AIR MOTOR
22:1 RATIO
6” STROKE
INCLUDE MANUALS: 66301-X LOWER PUMP END (PN 97999-647) &
S-632 GENERAL INFORMATION MANUAL (PN 97999-624)
SPECIFICATIONS, SERVICE KITS, GENERAL INFORMATION, TROUBLESHOOTING
650484-XXX
300 SERIES STAINLESS STEEL
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
xUse only genuine ARORreplacement parts to assure compatible
pressure rating and longest service life.
x61268 for repair of Air Motor section.
Service Note: The Air Motor Service/Parts Manual is not shipped
with the pump but it is included with each Service Kit. If this Service /
Parts Information isneeded, request the Air Motor Operator’s Manu-
al from ARO. (Manual 6544X-X, PN 97999-64).
x637306-X43 for repair of Lower Pump section.
Refer to the chart on page 2 for description of -XXX options.
SPECIFICATIONS
Model Series (Refer to option chart) 650484-XXX........
Type Air Operated, Two Ball..........................
Ratio 22:1..........................
Air Motor 65465-B.......................
Motor Repair Kit 61268................
Motor Diameter 4-1/4” (10.8 cm).................
Stroke 6”........................
Air Inlet (female) 1/2 - 14 N.P.T.F. - 1................
Air Exhaust (female) 1-1/4 - 11-1/2 N.P.T.F. - 1.............
Lower Pump End Series 66301-XXX...........
Lower Pump Repair Kit 637306-X43...........
Material Inlet (female) 1 - 11-1/2 N.P.T.F. - 1 &............
(male) 2 - 11-1/2 P.T.F. (short).............
Material Outlet (female) 1 - 11-1/2 N.P.T.F. - 1...........
Weight 42.9 lbs (19.5 kgs).........................
PERFORMANCE
Air Inlet Pressure Range 30 - 150 p.s.i. (2 - 10.3 bar)..........
Fluid Pressure Range 660 - 3412 p.s.i. (46 - 235 bar)..........
Maximum Rec’d Cycles / Minute 60.....
Displacement In3Per Cycle 7.5.........
Volume / Cycle 4.1 oz. (121 ml)...................
Cycles Per Gallon 30.9................
Flow @ 60 Cycles / Minute 1.9 g.p.m. (7.2 l.p.m.)..........
Noise Level @ 60 p.s.i. - 40 c.p.m. 81.8 db(A) *....
*The pump sound pressure level has been updated to an Equivalent Continuous Sound
Level (LAeq) to meet the intent of ANSI S1. 13-1971, CAGI-PNEUROP S5.1 using four
microphone locations.
PUMP DATA
Air Motor 65465-B
(See Manual 6544X-X)
FIGURE 1
Material Outlet (female)
1 - 11 -1/2 N .P.T.F. - 1
Material Inlet
Lower Pump
66301-XXX
Air Inlet (female)
1/2 - 14 N.P.T.F. - 1
Spacer Section
12-11/16
(322 mm)
1 - 11 -1/2 N .P.T.F. - 1
(female inlet)
2 - 11 -1/2 P.T.F. SAE
SPEC. SHORT (male inlet)
32_FROM AIR EXHAUST
Accessories Available: 91790 Silencer, 66101 Wall Bracket.
NUT Y85-29-C (3)
SPACER ROD 94209 (3)
CONNECTOR
See Figure 2
(See Manual 66301-X)
MODEL 650484-XXX
39-3/4
(1009 mm)
18-15/16
(481 mm)
SPRING 94674
IMPORTANT
This is one of the four documents which support the pump. Re-
placement copies of these forms are available upon request.
=650484-X MODEL OPERATOR’S MANUAL
-GENERAL INFORMATION - INDUSTRIAL PISTON PUMPS
-66301-X LOWER PUMP END OPERATOR’S MANUAL
-6544X-X AIR MOTOR OPERATOR’S MANUAL
www.ingersollrandproducts.com
CCN 99434656
5-19-11
F )
Tested with 91790 silencer installed .
*

Page 2of 2 650484-X
PUMP OPTION DESCRIPTION CHART
650484-X
PACKING MATERIAL
PLUNGER TYPE
SPRING ARRANGEMENT
(PACKINGS ARE UPPER AND LOWER UNLESS NOTED)
PACKING MATERIAL
SPRING ARRANGEMENT
4 Multiple Wave Spring w/
316 Stainless Steel Balls
7 Multiple Wave Spring w/
440 Stainless Steel Balls
PLUNGER TYPE
3 Hardened Stainless Steel w/
Hard Chrome Plating
B Hardened Stainless Steel w/
Ceramic Coating
3 Glass filled PTFE P UHMW-PE / PTFE staggered (upper)
C UHMW-PE UHMW-PE (lower)
G UHMW-PE / Leather staggered R PTFE / UHMW-PE staggered (upper)
PTFE (lower)
XX
GENERAL DESCRIPTION
WARNING HAZARDOUS PRESSURE. Do not exceed maxi-
mum operating pressure of 3300 p.s.i. (228 bar) at 150 p.s.i.
(10.3 bar) inlet air pressure.
PUMP RATIO X
INLET PRESSURE TO PUMP MOTOR =MAXIMUM PUMP FLUID PRESSURE
Pump ratio is an expression of the relationship between the pump motor area and
the lower pump end area. EXAMPLE: When 150 p.s.i. (10.3 bar) inlet pressure is
supplied to the motor of a 6:1 ratio pump it will develop a maximum of 750 p.s.i. (52
bar) fluid pressure (at no flow) - as the fluid control is opened, the flow rate will in-
crease as the motor cycle rate increases to keep up with the demand.
WARNING Refer to general information sheet for additional
safety precautions and important information.
xThe Two-Ball pumps are primarily designed for the pumping of me-
dium viscosity fluids, Stainless Steel construction offers compatibili-
ty with a wide range of fluids. The two-ball design provides better
priming of the lower foot valve. The double acting feature is standard
in all ARO industrial pumps, material is delivered to the pump dis-
charge outlet on both the up and down stroke.
xThe motor is connected to the lower pump end by a spacer section.
This allows for lubrication of the upper packing gland and prevents
motor contamination because of normal wear and eventual leakage
through the material packing gland. Be sure the solvent cup is ade-
quately filled with lubricant to protect the upper packings and insure
longest service life.
TROUBLE SHOOTING
Pump problems can occur in either the Air Motor Section or the Lower
Pump End Section, use these basic guidelines to help determine which
section is affected.
If the pump will not cycle.
xBe certain to first check for non-pump problems including kinked, re-
strictive or plugged inlet / outlet hose or dispensing device. Depres-
surize the pump system and clean out any obstructions in the inlet /
outlet material lines.
xRefer to the motor manual for trouble shooting if the pump does not
cycle and / or air leaks from the air motor.
If the pump cycles but does not deliver material.
xRefer to the lower pump end manual for further trouble shooting.
PUMP CONNECTION -- UPPER / LOWER
NOTE: All threads are right hand.
1. Lay the pump assembly on a workbench.
2. Remove the three nuts from the three spacer rods. (Fig. 1)
3. Pull the air motor from the lower pump end until motor piston rod is in
the “down” position and lower pump end rod is in “up” position.
4. Using e-ring pliers, slide the retaining ring up far enough to allow the
sleeve to move upward and release the two connectors. (Fig. 2)
Lower Pump
Piston Rod
Pump Motor
Piston Rod RETAINING RING
90102
SLEEVE
90109
CONNECTOR
90096 (2)
PUMP CONNECTOR DETAIL
FIGURE 2
REASSEMBLY
1. Align the pump motor with the lower pump end.
2. Install the two connectors and retain with the sleeve, slide the retain-
ing ring back into position.
3. Reinstall the spacer rods to the pump motor.
4. Bring the motor and lower pump together and retain with the three
nuts.
PN 97999-653