InHand InRouter202 User manual

InRouter202 Industrial Router
User Manual
Issue: V1.0—August, 2021

Declaration
Thank you for choosing our product. Before using the product, read this manual carefully.
The contents of this manual cannot be copied or reproduced in any form without the written
permission of InHand.
Due to continuous updating, InHand cannot promise that the contents are consistent with the
actual product information, and does not assume any disputes caused by the inconsistency of
technical parameters. The information in this document is subject to change without notice.
InHand reserves the right of final change and interpretation.
© 2020 InHand Networks. All rights reserved.
Conventions
Symbol
Indication
< >
Content in angle brackets “<>” indicates a button name. For example, the <OK> button.
""
'''' indicates a window name or menu name. For example, the pop-up window "New
User."
>
A multi-level menu is separated by the double brackets ">". For example, the
multi-level menu File > New > Folder indicates the menu item [Folder] under the
sub-menu [New], which is under the menu [File].
Cautions
Means reader be careful. Improper action may result in loss of data or device damage.
Note
Notes contain detailed descriptions and helpful suggestions.
Contact Us
Add: 3900 Jermantown Rd., Suite 150, Fairfax, VA 22030 USA
E-mail: [e-mail]
T: [phone]
URL: www.inhandnetworks.com

UL MARKINGS:
1.UL File：E364742、E509340.
2.Electrical ratings：Input: 9-36 Vdc, 0.1-0.2A. (Optional)
3.Model number：IR202
5.Ambient temperature range：-20 C to +70 C
6. Temperature class：T-5
7.Class I, Division 2, Groups A, B, C and D Hazardous Locations
UL INSTALLATION AND OPERATING INSTRUCTIONS:
1.These devices are open-type devices that are to be installed in an enclosure suitable for
the environment and where the internal compartment is only accessible by the use of tool.
2.“Suitable foruse in class 1, division 2, groupsA, B, C and D hazerdous locations, or
nonhazardous locations only.”
3.Warning - explosion hazard - do not disconnect equipment while the circuit is live or
unless the area is known to be free of ignitable concentrations.
4.The unit shall be powered by a ULlisted externalAC adapter, output rated 9-36 VDC,
MIN-MUM: 0.1-0.2A, marked LPS or CLASS 2

Contents
I. INTRODUCTION.................................................................................................................................1
1.1 OVERVIEW...................................................................................................................................1
1.2 PANELINTRODUCTION.............................................................................................................1
1.3 LED INDICATION ........................................................................................................................2
1.4 RESET TO DEFAULT FACTORY SETTING.............................................................................................3
II. INSTALLATION.................................................................................................................................4
2.1 PREPARATIPNS............................................................................................................................4
2.2 INSTALLATION............................................................................................................................5
2.2.1 SIM/UIM Card........................................................................................................................5
2.2.2 Antenna ...................................................................................................................................5
2.2.3 Power Supply..........................................................................................................................5
2.3 LOGIN ROUTER...........................................................................................................................5
III. WEB CONFIGURATION..................................................................................................................7
3. 1SYSTEM .......................................................................................................................................7
3.1.1 Basic Setup..............................................................................................................................7
3.1.2 System Time............................................................................................................................7
3.1.3 Admin Access..........................................................................................................................8
3.1.4 Configuration Management...................................................................................................10
3.1.5 Schedule................................................................................................................................11
3.1.6 Upgrade.................................................................................................................................11
3.1.8 Reboot...................................................................................................................................12
3.1.9 Logout...................................................................................................................................12
3.2 NETWORK..................................................................................................................................12
3.2.1 CELLULAR..........................................................................................................................12
3.2.2 WAN/LAN Switch ................................................................................................................14
3.2.3 WAN(STA)............................................................................................................................16
3.2.4 LAN ......................................................................................................................................16
3.2.5 WLAN Client (AP Mode) .....................................................................................................17

3.2.6 WLAN Client (STAMode) ...................................................................................................18
3.2.7 Static Route...........................................................................................................................19
3.3 SERVICE......................................................................................................................................19
3.3.1 DHCP service........................................................................................................................19
3.3.2 DNS.......................................................................................................................................20
3.3.3 DNS Relay ............................................................................................................................21
3.3.4 Device Manager ....................................................................................................................22
3.3.5 DTU RS232...........................................................................................................................22
3.3.6 Traffic Manager.....................................................................................................................23
3.3.7 Alarm Manager......................................................................................................................24
3.3.8 User Experience Plan............................................................................................................25
3.4 FIREWALL ..................................................................................................................................25
3.4.1 Basic......................................................................................................................................25
3.4.2 Filtering.................................................................................................................................26
3.4.3 Content Filtering ...................................................................................................................26
3.4.4 Port Mapping.........................................................................................................................27
3.4.5 Virtual IP Mapping................................................................................................................27
3.4.6 DMZ......................................................................................................................................28
3.4.7 MAC-IP Binding...................................................................................................................28
3.4.8 NAT.......................................................................................................................................29
3.5 VPN..............................................................................................................................................29
3.5.1 IPSec Settings........................................................................................................................30
3.5.2 IPSec Tunnels........................................................................................................................31
3.5.3 Certificate Management ........................................................................................................33
3.6 TOOLS.........................................................................................................................................33
3.6.1 PING Detection.....................................................................................................................33
3.6.2 Traceroute..............................................................................................................................34
3.7STATUS........................................................................................................................................34
3.7.1 System...................................................................................................................................34
3.7.2 Modem..................................................................................................................................34

3.7.3 Traffic Statistics.....................................................................................................................35
3.7.4 Alarm.....................................................................................................................................35
3.7.5 WLAN...................................................................................................................................35
3.7.6 Network Connections............................................................................................................36
3.7.7 Device Manager ....................................................................................................................36
3.7.8 Route Table ...........................................................................................................................36
3.7.9 Device List............................................................................................................................36
3.7.10 Log......................................................................................................................................37
3.7.11 Third Party Software Notices..............................................................................................37
APPENDIX A FAQ................................................................................................................................38
APPENDIX B INSTRUCTION OF COMMAND LINE.......................................................................40

1
I. INTRODUCTION
1.1 OVERVIEW
The InRouter202 (IR202) is an IoT cellular router that integrates 4G LTE, Wi-Fi, and VPN
technology to provide an easy, reliable, and secure Internet connectivity. With technologies such
as 4G wireless wide area network and Wi-Fi wireless local area network, it provides uninterrupted
multiple network access capabilities, and with its comprehensive security and wireless services, it
realizes up to 10 thousands equipments networking and provides high-speed data access for
equipment networking.
This product is suitable for the networking of unattended devices and sites. It is embedded with
watch dog and multi-layer link detection mechanisms to ensure reliable and stable
communications. The router can be deployed easily to build large scale networks scaling up to
tens of thousands of devices. Using our InHand Device Manager cloud platform, users can
manage their network efficiently.
IR202 can be used in a wide range of industrial and commercial IoT applications, providing an
option of good balance between cost and performance.
1.2 PANEL INTRODUCTION

2
1.3 LED INDICATION
ER202 LED
STATUS
SYS
Off --- Power off
Blink in red --- Device starting
Steady in red --- Device working
CELL
Off --- Cellular disable
Blink in green --- Cellular connecting
Steady in green --- Cellular connected
Wi-Fi
Off --- Wi-Fi disable
Blink in green --- Wi-Fi working / Data transferring

3
1.4 Reset to default factory setting
1. When the device is powered on, press the Reset button immediately and keep it for 10 seconds
until the SYS is steady on
2. Loosen the Reset button, SYS will be off.
3. Press and hold Reset button again, then SYS flashes. Loosen the Reset button and device will
restore to factory setting successfully.

4
II. INSTALLATION
2.1 PREPARATIPNS
Precautions:
Please make sure there is 4G network coverage and there is no shield on site. 220V AC or 9~36V
DC shall be provided on site. First installation shall be done under direction of the engineer
recognized by InHand Networks.
1 PC
OS: Windows XP, Windows 7, Windows 10
CPU: PII 233 higher
Memory: 32M higher
Hard disk: 6.4G higher
Serial port:At least one
Ethernet port:At least one (10M/100M)
IE version: 10.0 higher
Resolution: 640*480 higher
1 SIM card:
Ensure the card is enabled with data service and its service is not suspended
because of an overdue charge.
Power supply:
220VAC: can be used with DC power of the device
9~36V DC: Ripple voltage < 100 mV
Fixation:
Please place InRouter on flat level and have it installed in an environment with
small vibrational frequency.
The device shall be installed and operated in powered-off status!

5
2.2 INSTALLATION
2.2.1 SIM/UIM Card
Insert SIM card into SIM card slot according to the icon on InRouter202. Press the SIM card to
pop up it.
2.2.2 Antenna
Slightly rotate the movable part of metal SMA-J interface until it cannot be rotated (at this time,
external thread of antenna cable cannot be seen). Do not forcibly screw the antenna by holding
black rubber lining.
2.2.3 Power Supply
Upon installation of the antenna, connect the device to 9~36V DC power and see if the Power
LED on the panel of the device is on. If not, please contact technical support of InHand Networks
immediately.
2.3 LOGIN ROUTER
Upon installation of hardware, be sure the Ethernet card has been mounted in the supervisory PC
prior to logging in the page of Web settings of the router.
I. Automatic Acquisition of IPAddress (Recommended)
Please set the supervisory computer to "automatic acquisition of IP address" and "automatic
acquisition of DNS server address" (default configuration of computer system) to let the device
automatically assign IP address for supervisory computer.
II. Set a Static IPAddress
Set the IP address of supervisory PC (such as 192. 168. 2. 2) and LAN interface of device in same

6
network segment (initial IP address of LAN interface of device: 192. 168. 2. 1, subnet mask: 255.
255. 255. 0).
III. Cancel the Proxy Server
If the current supervisory PC uses a proxy server to access the Internet, it is required to cancel the
proxy service. The operating steps are shown below: 1) In the browser window, select
"tools>>Internet options"; 2) select "connection" page and click the button of LAN Settings to
enter "LAN Settings" window interface. Please confirm if the option "Use a Proxy Server for
LAN" is checked; if it is checked, please cancel and click the button <OK>.
IV. Log in Web Settings Page
Open IE or other browser and enter IP address of InRouter202, such as http://192.168.2.1 in
address bar (default setting of InRouter202. Upon connection, log in from the login interface as
Admin, i.e. enter username and password at the login interface (user name /password default:
adm/123456).
For security, you are suggested to modify the default login password after the first login and
safe keep the password information.

7
III. WEB CONFIGURATION
This chapter will introduce how to configure your router via Web.
3. 1 SYSTEM
The system configuration process involves ten steps, including basic setup, time, admin access,
system Log, configuration management, schedule, upgrade, reboot and logout. Here, system and
network state and system time of synchronizing device and PC can be checked and router WEB
configuration interface language can be set as well as the name of mainframe of router can be
customized.
3.1.1 Basic Setup
Here, WEB configuration interface language can be set; name of mainframe of router can be
customized.
From the navigation tree, select System >> Basic Setup, then enter the “Basic Setup” page.
Table 3-1-1 Basic Setup Parameters
Basic settings
Function description: Select display language of the router configuration interface and set
personalized name.
Parameters
Description
Default
Language
Configure language of WEB configuration interface
Chinese
Host Name
Set a name for the host or device connected to the router
for viewing.
Router
3.1.2 System Time
To ensure the coordination between this device and other devices, user need to set the system time
in an accurate way since this function is used to configure and check system time as well as
system timezone. System time is used to configure and view system time and system time zone.
It aims to achieve time synchronization of all devices equipped with a clock on network so as to
provide multiple applications based on synced time.

8
From the navigation tree, select System >> Time, then enter the “Time” webpage, as shown below.
Click <Sync Time> to synchronize the time of the gateway with the system time of the host.
Table 3-1-2 Parameters of System Time
System Time
Function description: Set local timezone and automatic updating time of NTP.
Parameters
Description
Default
Time of Router
Display present time of router
8:00:00 AM, 12/12/2015
PC Time
Display present time of PC
Present time
Timezone
Set timezone of router
Custom
Custom TZ String
Set TZ string of router
CST-8
Auto update Time
Select whether to automatically update
time, you may select when startup or
very 1/2/...hours.
Disable
3.1.3 Admin Access
Admin services include HTTP, HTTPS, TELNET, SSHD, HTTPAPI and console.
HTTP
HTTP (Hypertext Transfer Protocol) is used for transferring web pages on Internet. After enabling
HTTP service on device, users can log on via HTTP and access and control the device using a web
browser.
HTTPS
HTTPS (Secure Hypertext Transfer Protocol) is the secure version of hypertext transfer protocol.
As a HTTP protocol which supports SSL protocol, it is more secure.
TELNET
Telnet protocol provides telnet and virtual terminal functions through a network. Depending on
Server/Client, Telnet Client could send request to Telnet server which provides Telnet services.
The device supports Telnet Client and Telnet Server.
SSHD
SSH protocol provides security for remote login sessions and other network services. The SSHD
service uses the SSH protocol, which has higher security than Telnet.
HTTP_API
User can check router’s status and configure router without login the router remotely by sending

9
HTTP request with HTTP API. Please ask to technical support for more information about HTTP
API.
Console
The console port, also called the access or serial port, refers for initial configuration and
subsequent management of a device. It has the same terminal as the telnet client. Console port is
located in the router, please do not open the router by yourself.
From the navigation tree, select System >> Admin Access, then enter “Admin Access” page.
Table3-1-3 Parameters of Admin Access
Admin Access
Function description:
1. Modify username and password of router.
2. The router may be set by the following 5 ways, i.e. http, https, telnet, SSHD and console.
3. Set login timeout.
Parameters
Description
Default
Username/Password
Username
Set name of user who logs in WEB configuration
adm
Old
Password
Previous password access to WEB configuration
123456
New
Password
New password access to WEB configuration
N/A
Confirm
New
Password
Reconfirm the new password
N/A
Amin functions
Service Port
Service port of
HTTP/HTTPS/TELNET/SSHD/HTTP_API/Console
80/443/23/22/4444
Local
Access
Enable - Allow local LAN to administrate the router
with corresponding service (e.g. HTTP)
Disable - Local LAN cannot administrate the router with
corresponding service (e.g. HTTP)
Enable
Remote
Access
Enable - Allow remote host to administrate the router
with corresponding service (e.g. HTTP)
Disable - Remote host cannot administrate the router
with corresponding service (e.g. HTTP)
Enable
Allowed
Access from
WAN
(Optional)
Set allowed access from WAN (only
HTTP/HTTPS/HTTP_API)
The host
controlling service
at this moment can
be set, e.g.
192.168.2.1/30
or

10
192.168.2.1-192.1
68.2.10
Description
For recording significance of various parameters of
admin functions (without influencing router
configuration)
N/A
Console Login User (Click <new> button after setting a group of username and
password)
Username
Configure console login user, custom
N/A
Password
Configure the password, custom
N/A
Other Parameters
Log
Timeout
Set login timeout (router will automatically disconnect
the configuration interface after login timeout)
500 seconds
In “Username/Password” section, users can modify username and password rather than
create new username, i.e. only this username can be used in logins.
In “Console Login User” section, we can create multiple usernames, i.e. multiple
usernames can be used by serial port or TELNET console logins.
3.1.4 Configuration Management
Here you can back up the configuration parameters, import the desired parameters backup and
reset the router.
From the navigation tree, select System >> Configuration Management, then enter the
“Configuration Management” page.
Table 3-1-4 Parameters of Configuration Management
Configuration Management
Function description: Set parameters of configuration management.
Parameters
Description
Default
Browse
Choose the configuration file
N/A
Import
Import configuration file to router
N/A
Backup
Backup configuration file to host
N/A
Restore default
configuration
Select to restore default configuration (effective after
rebooting)
N/A
Modem drive
program
For configuring drive program of module
N/A
Network Provider
For configuring APN, username, password and other
N/A

11
(ISP)
parameters of the network providers across the world
Validity and order of imported configurations should be ensured. The good configs will later
be serially executed in order after system reboot. If the configuration files didn’t be arranged
according to effective order, the system won’t enter the desired state.
In order not to affect the operation of the current system, when performing an import
configuration and restore default configuration, users need to restart the device to make the
new configuration to take effect.
3.1.5 Schedule
After this function is enabled, the device will restart as the scheduled time.
From the navigation tree, select System >> Task Schedule, then enter “Task Schedule” page.
3.1.6 Upgrade
The upgrading process can be divided into two steps. In the first step, upgrading files will be
written in backup firmware zone, in the second step: files in backup firmware zone will be copied
to main firmware zone, which should be carried out during system restart. During software
upgrading, any operation on web page is not allowed, otherwise software upgrading may be
interrupted.
From the navigation tree, select System >> Upgrade, then enter the “Upgrade” page.
To upgrade the system, firstly, click <Browse> choose the upgrade file, secondly, click <Upgrade>
and then click <OK> to begin upgrade; thirdly, upgrade firmware succeed, and click <Reboot> to
restart the device.

12
3.1.8 Reboot
Please save the configurations before reboot, otherwise the configurations that are not saved will
be lost after reboot.
To reboot the system, please click the System>>Reboot, then click <OK>.
3.1.9 Logout
To logout, click System >> Logout, and then click <OK>.
3.2 NETWORK
3.2.1 CELLULAR
Insert SIM card and dial to achieve the wireless network connection function of router.
Click the “Network>>Cellular” menu in the navigation tree to enter the cellular configuration
page.
Table3-2-1-1 Parameters of Cellular
Dialup/Cellular Connection
Function description: Configure parameters of PPP dialup. Generally, users only need to set
basic configuration instead of advanced options.
Parameters
Description
Default
Enable
Enable PPP dialup.
Enable
Time Schedule
Set time schedule
ALL
Shared connection
(NAT)
Enable—Local device connected to Router
can access to the Internet via Router.
Disable—Local device connected to Router
cannot access to the Internet via Router.
Enable
Default Route
Enable default route
Enable
Network Provider (ISP)
For selecting network provider providing
service at present
Custom
APN (inapplicable to
CDMA2000 series)
Mobile carrier provides relevant parameters
(subject to local carrier)
cmnet/uninet
Dialing Number
Relevant dialing parameters provided be
mobile carriers (subject to local carrier)
“*99#”“*99***1#”
(China Mobile,
China

13
Unicom)#777(Chin
a Telecom)
Username
Relevant dialing parameters provided be
mobile carriers (subject to local carrier)
“gprs” (China
Mobile, China
Unicom)
CARD(China
Telecom)
Password
Relevant dialing parameters provided be
mobile carriers (subject to local carrier)
“gprs” (China
Mobile, China
Unicom)
CARD(China
Telecom)
Network Type
Auto, 2G Only, 3G Only, 4G Only
Auto
Connection Mode
Optional always online, dial on demand,
manual dialing
Always Online
Redial Interval
Set the redialing time when login fails.
30 s
Show Advanced Options
Initial Commands
Set initial commands
AT
PIN Code
For setting PIN code
N/A
MTU
Set max. transmission unit
1500
Authentication method
Optional:Auto, PAP, CHAP
Auto
Use Peer DNS
Click to receive peer DNS assigned by the
mobile carrier
Enable
Link detection interval
Set link detection interval
55 s
Debug
Enable debug mode
Disable
Debug Modem
Enable debug modem
Disable
ICMP Detection Mode
Ignore Traffic/ Monitor Traffic
Ignore Traffic
ICMP Detection Server
Set the ICMP Detection Server. N/A
represents not to enable ICMP detection.
N/A
ICMP Detection
Interval
Set ICMP Detection Interval
30 s
ICMP Detection
Timeout
Set ICMP Detection Timeout (the detection
server will reboot if ICMP times out)
20 s
ICMP Detection Retries
Set the max. number of retries if ICMP fails
(redial if reaching max. times)
5
able3-2-1-2 Parameters of Dialup/Cellular - Schedule
Administration of dialup/Cellular - Schedule
Function description: Online or offline based on the specified time.
Parameters
Description
Default
Name of Schedule
schedule 1
schedule1
Sunday ~ Saturday
Click to enable

14
Time Range 1
Set time range 1
9:00-12:00
Time Range 2
Set time range 2
14::00-18:00
Time Range 3
Set time range 3
0:00-0:00
Description
Set description content
N/A
3.2.2 WAN/LAN Switch
WAN/LAN1 Port supports two types of work mode, include WAN and LAN.
Click the “Network>>WAN/LAN Switch” to set work mode
WAN supports three types of wired access including static IP, dynamic address (DHCP) and
ADSL (PPPoE) dialing.
DHCP adopts Client/Server communication mode. Client sends configuration request to Server
which feeds back corresponding configuration information, including distributed IP address to the
Client to achieve the dynamic configuration of IP address and other information.
PPPoE is a point-to-point protocol over Ethernet. User has to install a PPPoE Client on the basis
of original connection way. Through PPPoE, remote access devices could achieve the control and
charging of each accessed user.
WAN of the device is disabled by default.
Table 3-2-2-1 Static IP Parameters of WAN
WAN - Static IP
Function description:Access to Internet via wired lines with fixed IP.
Parameters
Description
Default
Shared connection (NAT)
Enable—Local device connected to
Router can access to the Internet via
Router.
Disable—Local device connected to
Router cannot access to the Internet via
Router.
Enable
Default route
Enable default route
Enable
MAC Address
MAC Address of the device
00:18:05:08:07:3D
(provided by
InHand Networks),
provided for device
manufacturer
IPAddress
Set IP address of WAN
192.168.1.29