InHand IR300 Series Operating and maintenance instructions

IR300 Series of Industrial Routers
Quick Installation Manual
Data Version: V 1.0—2020.6

Directory
Overview........................................................................................................................................................1
I. Packing list..................................................................................................................................................1
II.Panel Introduction and Structural Size........................................................................................................2
2.1 Panel Introduction ............................................................................................................................2
2.2 Structural Size ..................................................................................................................................3
III. Installation of Wireless Routers................................................................................................................3
3.1 Slippery Course Installation and Disassembly.................................................................................3
3.1.1 Slippery Course Installation ..................................................................................................3
3.1.2 Slippery Course Disassembly................................................................................................4
3.2 Wall Hanging Installation and Disassembly.....................................................................................5
3.2.1 Wall Hanging Installation......................................................................................................5
3.2.2 Wall Hanging Disassembly....................................................................................................6
3.3 SIM Card Installation .......................................................................................................................6
3.4 Antenna Installation..........................................................................................................................6
3.5 Power Installation.............................................................................................................................8
3.6 Ground Installation...........................................................................................................................8
IV. Quick access to Internet............................................................................................................................9
4.1 Wired to Internet...............................................................................................................................9
4.2 SIM Card Dial-Up..........................................................................................................................14
4.3 WiFi to Internet...............................................................................................................................15
V. DM Cloud Management Platform............................................................................................................20
5.1 Environmental Conditions..............................................................................................................20
5.2 Platform Account Creation.............................................................................................................21
5.3 Add Device to Platform..................................................................................................................21
VI. Quick-Use Guidance..............................................................................................................................22
6.1 Restore Factory Setting ..................................................................................................................22
6.1.1 Web Setting..........................................................................................................................22
6.1.2 Hardware Restored..............................................................................................................23
6.2 Import/Export Configuration..........................................................................................................23
6.3 Log and Diagnostic Records...........................................................................................................24
VII. Description of panel indicator...............................................................................................................24
7.1 Panel LED Indicator Description....................................................................................................24

1
Overview
This manual is for the installation and operation of IR300 series routers of InHand Network Company.
InHand makes every effort to provide accurate information in
this manual, but InHand does not guarantee that there is no error in the manual. All statements,
information and recommendations in this manual do not constitute any expressed or implied warranty.
Please confirm the product model and packaging accessories (power terminal, antenna). Please purchase
SIM cards from local network operators.
I. Packing list
Each IR300 product includes common accessories (such as standard accessories list), please check
carefully, when you receive our products.Please contact the sales staff of InHand, if there is any
missing or damage.
In addition, according to different site characteristics, InHand can provide customers with optional
accessories . For details, please refer to the list of optional accessories.
Standard Accessories
Accessories
Unit
Description
IR 300
1
IR300 series industrial 4G routerrouters
Hanging ear
1
Fixed router
Power terminal
1
2-pin Green Power Terminal
Ethernet cable
1
1.5 m Ethernet cable
Antenna
1
3G /4G antenna
Product warranty card
1
Warranty period 1 year
Certificate of approval
1
IR 300 series industrial 4 G router certification
Optional accessories
Accessories
Unit
Description
Power supply
1
VDC power adapter
Antenna
1
WiFi antenna
Equipment slippery course
1
Fixed router

2
II.Panel Introduction and Structural Size
2.1 Panel Introduction
Figure 2-1 Equipment Panel

3
2.2 Structural Size
Figure 2-2 Equipment Structure
III. Installation of Wireless Routers
Precautions for installation:
●Power requirements :12v DC (9~36 v DC), please pay attention to the power voltage levell; rated
current is 0.2~0.22 A.
● environmental requirements: working temperature-20℃~70℃, storage temperature-40℃~85℃,
relative humidity 5%~95%(no frosting), equipment surface may be high temperature, installation
needs to consider the surrounding environment, should be installed in the restricted area
●Avoid direct sunlight, away from heat sources or areas with strong electromagnetic interference
●Routers support wall hanging & Slippery course installation
●Check for cables and connectors required for installation
3.1 Slippery Course Installation and
Disassembly
3.1.1 Slippery Course Installation
The steps are as follows:

4
Step 1: Select the installation location of the device and make sure there is enough space.
Step 2: Tilt the equipment to the right 45 ° , so that the upper part of the DIN rail seat is stuck on the DIN
rail, holding the lower end of the equipment, up slightly to rotate the equipment, the DIN rail seat can be
stuck on the DIN rail. Verify that the equipment is fixed on DIN rail
Figure 3-1-1 Slippery Course Installation
3.1.2 Slippery Course Disassembly
The steps are as follows:
Step 1: Hold the bottom end of the equipment with one hand and the top end of the slippery course side
with the other hand, push lower end of the device to leave the DIN rail.
Step 2: Turn the equipment clockwise and lift the equipment, removed the equipment from the DIN rail
Push
inward

5
Figure 3-1-2 Slippery Course Disassembly
3.2 Wall Hanging Installation and
Disassembly
3.2.1 Wall Hanging Installation
The steps are as follows:
Step 1: Fix the hanging ear to both sides of the device with screws
Step 2: Fix the hanging ear to the wall with screws.
Figure .3-2-1 Wall Hanging Installation
Push
Push
outwar
d

6
3.2.2 Wall Hanging Disassembly
Use one hand to hold the device and the other hand to remove the screws with screwdriver, remove device
from the fixed position
3.3 SIM Card Installation
IR300 support dual SIM card, hold down SIM pop-up button will pop up the card holder, load the SIM card
Figure 3-3 SIM Card Installation
3.4 Antenna Installation
Rotate the metal interface clockwise until the movable part can not be rotated, do not hold the black glue
stick to twist the antenna.

7
Figure 3-4-a Glue Stick Antenna Installation
Figure 3-4-b Chuck Antenna Installation

8
Note
IR300 support dual antennas, ANT antenna and AUX antenna. The ANT antenna is the antenna which
receives and transmits data, AUX antenna can only enhance the antenna signal degree and can not
receieve and sent data, so it can’t be used alone. Generally, only use ANT antenna.
3.5 Power Installation
The steps are as follows:
Step 1: Remove power terminal from router;
Step 2: Unscrew the locking screw on the power terminal;
Step 3: Insert the power cable into the terminal and lock the screws
Figure 3-5 Power Supply Installation
3.6 Ground Installation
The steps are as follows:
Step 1: Unscrew the ground nut;
Step 2: Put the grounding ring of the cabinet ground wire into the ground stud;
Step 3: Tighten the ground nut.

9
Attention
In order to improve the anti-jamming ability of the router, the router must be grounded when it is used, and
the ground wire is connected to the grounding stud of the router according to the actual use environment.
IV. Quick access to Internet
The device supports three ways of accessing the Internet: Wired, Cellular Dial-Up, WiFi
note: when the device does not use Celluar Dial-up access, the "dial-up interface" must be disabled,
otherwise the device cycle dial-up to the maximum number, it will lead to device restart, network business
interruption.
Figure 4 Disable Cellular Dial-Up
4.1 Wired to Internet
Step 1: Plug in the power cord and network cable according to the diagram, connect WAN port to the
Internet, connect LAN2 port to PC.

10
Figure 4-1 Ethernet Connection
Step 2: Set the PC in the same network segment as the ip address of gateway device.
Method 1: DHCP automatically get the address (Recommended)
Method 2: Use fixed IP address, set the PC and gateway in the same address segment
(DHCP Server for LAN2 Port is default enabled)
Figure 4-1-2 Dynamic acquisition/manual Configuration
PC only needs to configure the IP address to any value in:
“192.168.2.2.2~192.168.2.254”
The gateway is set to: “192.168.2.1”, the subnet mask is: “255.255.255.0”
The DNS is configured to “operator DNS server address”.

11
Step 3: Input the device default address 192.168.2.1 in the browser, enter the device Web page
management
(If the page indicates that the page is not secure, open hidden or advanced, select continue to go)
Figure 4-1-3 Login WEB Page Management
Step 4: Configuration WAN port, click on the navigation bar "Network >>WAN/LAN Switch" ， select
WAN mode to configure IP address of Wan port, so that the device can access to the Internet..
(Make sure the interface is in WAN mode, initial default LAN mode)
Figure 4-1-4 WAN Port Setup

12
Step 5: Three ways to assign address, dynamic DHCP( recommended), static address, ADSL dial (click
application after configuration is completed)
Figure 4-1-4-a Dynamic Ip Configure of WAN
Figure 4-1-4-b Static Ip Configuration of WAN

13
Figure 4-1-4-c ADSL Dial-up of WAN
Step 6: Use the PING tool to verify your network connection.
Figure 4-1-5 Ping Result Diagram

14
4.2 SIM Card Dial-Up
Step 1: Insert the SIM card into the slot 1, /3 G/4G LTE the antenna to the ANT antenna column under the
power condition of the equipment, connect the network wire to the PC and connect to the power supply.
Attention
SIM card must be replaced or plugged, power off restart to avoid data loss or equipment damage.
Step 2: Open the browser, login device WEB interface. (refer to 4.1 Wired Connections >> first and second
steps)
Step 3: Click on the navigation bar "network >>Cellular" set dial-up access parameters, the device initial
default on dial-up function, wait a few minutes to access the Internet.
(if not dial-up,you can restart Cellular Service).
Figure 4-2-1 SIM Card Dial-Up
Step 4: The device supports dual card mode, when the SIM card insert card slot 2, need to enable dual SIM
card function in advanced settings, private network dial parameters can be set in the dial
parameter set, new click on the application, and then select at the cellular network operator.
Figure 4-2-2 Dialing Parameters

15
Step 5: Click on the navigation bar "status >> network connection" to view the network status, showing the
connected and assigned IP address and other status, indicating that the SIM card has successfully accessed
the Internet.
Figure 4-2-3 Dial-Up
4.3 WiFi to Internet
Step 1: WiFi the antenna to connect the WLAN antenna column, the network wire to the PC and insert the
power supply.
(Please refer to "4.1 Wired Networking >> Step 1, Step 2" for login WEB interface)
Step 2: Set WiFi two working modes: AP ， STA.
Mode 1: AP mode (initial default mode), the device acts as a wireless access point (Accsess Point) radiates
the wireless signal, the terminal device can be accessed through the connection AP. Ensure that the device
has been connected to the Internet through the above wired, cellular dialing mode. You can Set SSID name
and encryption authentication, k terminal connection password as your need.

16
Figure 4-3-1 SSID of AP
Mode 2: STA mode means that station, device does not have the function of Internet access, it needs to
connect to the AP device to provide bridges for the terminal equipment that can not connect to the AP, such
as the PC device.
Step 3: Click on the navigation bar "Network >>WLAN Mode Switch" to switch the working mode to the
STA, then apply and restart the device as prompted.
Figure 4-3-2- WLAN Mode Switch

17
Figure 4-3-2- Reboot Device
Step 4: Click on the navigation bar "Network >>WLAN Client ", click on the scan to select the target SSID,
set encryption and password.
Figure 4-3-4 Selected SSID

18
Step 5: Click on the navigation bar "Network >>WAN (STA)", set WAN port IP parameter
Three ways: dynamic address (recommended), static IP,ADSL dial.
Figure 4-3-5-a Dynamic Acquisition WAN (STA) Address
Figure 4-3-5- b Static IP Configuration of WAN (STA)