InHand ODU2002 User manual

InHand ODU2002 Outdoor Unit
Quick Installation Guide
Data Version: V1.3

Table of Contents
Overview.............................................................................................................................................................. 1
1. Packing list.................................................................................................................................................. 1
2. Panel Introduction................................................................................................................................... 2
3. Equipment Installation........................................................................................................................... 2
3.1 Insert SIM card................................................................................................................................... 2
3.2 Attach antennas ................................................................................................................................ 3
3.3 Install the ODU2002 ........................................................................................................................ 4
3.4 Cable installation .............................................................................................................................. 6
3.4.1 Grounding................................................................................................................................ 6
3.4.2 Connect the Ethernet Cable.............................................................................................. 7
3.4.3 Connect PoE Power Adapter............................................................................................. 8
3.5 Inspection after Installation.......................................................................................................... 8
3.5.1 Check the Device Installation ........................................................................................... 8
3.5.2 Check the Cable Connection ............................................................................................ 9
3.5.3 Check the Power Supply..................................................................................................... 9
4. Access to Internet........................................................................................................................................ 9
4.1 SIM Card Dial-up............................................................................................................................... 9
4.1.1 Connect via APP .................................................................................................................... 9
4.2.1 Connect via PC.....................................................................................................................12
4.2 Wired Networking..........................................................................................................................14
4.2.1 Connect via APP..................................................................................................................14
4.2.1 Configure via PC..................................................................................................................16
5. Remote Manage Platform......................................................................................................................19
5.1 InCloud Platform.............................................................................................................................19
5.1.1 Register/login to the Platform.......................................................................................19
5.1.2 Adding devices to the Platform.....................................................................................20
6. Quick User Guide.......................................................................................................................................20
6.1 Restore to Default Factory Settings.........................................................................................20
6.1.1 Reset/Restore Remotely ...................................................................................................20
6.1.2 Hardware Restore ...............................................................................................................21
6.2 Log and Diagnostic Data .............................................................................................................21
7. LED Status Reference................................................................................................................................22

1
Overview
This manual is for the installation and operation of the ODU2002 5G outdoor unit of
Inhand Networks . Before installation, please confirm the product model and accessories
in the package and purchase a SIM card from the operator that supports the local
network. Please refer to the actual product for specific operations .
1. Packing list
Every ODU2002 product shipped from the factory includes common accessories.
After you receive our product, please check carefully. If you find any missing or damaged,
please contact Inhand sales personnel in time.
Part Name
Quantity
Description
ODU2002
1
ODU2002 5G outdoor unit
Ethernet cable
1
1m Ethernet cable
Power adapter + AC
1
50V/0.3A PoE power adapter
support IEEE 802.3af standard
5G antenna
2
5G antenna*2
5G MIMO antenna
4
5G MIMO antenna*4
Wi-Fi antenna
1
Wi-Fi antenna*1
GNSS antenna
1
GNSS antenna*1
QSG
1
Quick Installation Guide
Mounting bracket
1
Adjustable bracket
Mounting plate
1
Mounting plate
Stainless steel pipe clamp
2
Support pole-mounted installation
Grounding wire
1
Ground connection

2
2. Panel Introduction
ODU2002NA
3. Equipment Installation
Precautions for installation:
⚫Power supply: ODU2002 is powered by 802.af standard (50V/0.3A), please pay
attention to the power voltage level.
⚫Environmental requirements: working temperature: -30℃～70℃, storage
temperature: -40℃～85℃.
⚫Support to be mounted with bracket. Avoid direct sunlight, away from heat source
or strong electromagnetic interference. Confirm that the installation position is
strong enough to support the weight of the equipment and its installation
accessories.
⚫Check for cables and antennas required for installation.
3.1 Insert SIM card
⚫ODU2002 supports dual nano SIM cards
⚫Unscrew the SIM card cover of the ODU2002, then insert the SIM card(s) according
to the following diagram.

3
⚫Put the SIM card cover back in place, make sure the waterproof gasket is properly
assembled to prevent leakage.
3.2 Attach antennas
⚫Attach eight antennas to the TNC connectors marked 5G/5G MIMO/Wi-Fi and GNSS.

4
3.3 Install the ODU2002
3.3.1 Install the Mounting plate
⚫Attach the mounting plate to the ODU2002 using screws. Please make sure the top
side facing upwards.
3.3.2 Wall-mounted Installation
⚫Install the adjustable base on the wall in the desired angle and position.

5
⚫Attach the mounted ODU2002 to the base. Tighten the mounting bolts to lock the
ODU2002 in place.
3.3.3 Pole-mounted Installation
⚫Install the adjustable base on the pole in the desired angle and position.

6
⚫Attach the mounted ODU2002 to the base. Tighten the mounting bolts to lock the
ODU2002 in place.
3.4 Cable installation
3.4.1 Grounding
⚫Connect the grounding hole of the device to the ground through the grounding wire
with OT terminal, cut the grounding wire into certain length according to field

7
situation to avoid waste.
3.4.2 Connect the Ethernet Cable
Notice
(1) Please make sure that the ethernet cable is inserted into the device in a
standardized way. If not, the crystal head may be damaged when installing the
waterproof PG head.
(2) When removing the ethernet cable, the waterproof PG head must be removed first,
and then the crystal head connected to the device must be removed.
(3) Please confirm the diameter of Ethernet cable is between 4.8 mm to 6.5 mm.
(4) Please ensure the cable glands are properly assembled to prevent leaks.
⚫Cut the Ethernet cable to the appropriate length according to the distance from
the ODU to the power supply and pass it through the bracket.
⚫Use the ethernet cable after the crystal head is processed and pass through the
waterproof PG head in the order shown in the figure below.
⚫Schematic diagram of patch cable passing through waterproof head
⚫Insert the Ethernet cable into the network port of the device, and tighten the
waterproof head in the order of B, C, D, E to complete the installation.

8
3.4.3 Connect PoE Power Adapter
⚫Connect one end of the Ethernet cable to the PoE 2.5G LAN1 port and plug the other
end into the 802.af(50V/0.3A) PoE Adapter or an router/switch with 802.3af port.
3.5 Inspection after Installation
3.5.1 Check the Device Installation
⚫Confirm the device is fully secured to prevent falling.

9
3.5.2 Check the Cable Connection
⚫Make sure the cables are bundled correctly.
⚫Avoid dragging and damaging the device, we recommend you to fix the Ethernet
cable on the bracket.
3.5.3 Check the Power Supply
⚫Confirm that the power cord is in good contact and meets safety requirements.
⚫Turn on the power to supply power to the device and confirm the device can work
normally.
4. Access to Internet
ODU2002 supports two ways of accessing to Internet: cellular and wired. Wi-Fi is only
used for configuration.
4.1 SIM Card Dial-up
4.1.1Connect via APP
⚫Insert the SIM card when device is power off, and connect the 5G antenna to the
device, and log in the InCloud APP.
⚫Click the "Device" directory below to enter the [Device] page, click the menu

10
button in the upper right corner, and select [Add Device]. Scan the QR code on
the ODU2002 to add device.
⚫After scanning the code successfully, configure the name, serial number, and
description information of the device.
⚫After adding the device, if the device fails to connect to the network, you can
click "Configure local device" to configure the device to connect to the cloud. The
ODU2002 enables the http access and Wi-Fi AP function by default.

11
⚫Scan the QR code on ODU2002, and then the APP will automatically connect to
the device via Wi-Fi.
⚫After the connection succeeds, APP will will automatically log in to the device and
enter the networking configuration interface, confirm the information and
submit.

12
4.2.1 Connect via PC
⚫Step 1: Power off the device, insert the SIM card into the card slot, connect the
5G antenna to the device, connect ODU2002 and PC with Ethernet cable.
⚫Step 2: Open a browser and enter the device's default address 192.168.1.1 in the
browser address bar. After entering the username and password (default:
adm/123456), enter the device's WEB management interface. If the page prompts
that the webpage is not secure, open the hidden or advanced options and select
"Proceed to website".
⚫Step 3: Click "Internet" on the left navigation bar, click the edit button behind the
"Cellular" button to set up the dial-up parameters, the device enables the dial-up
function by default, wait for a few minutes to go online, and re-enable the dial-
up if it is not dialed.

13
⚫Step 4: Check the dial-up status in the "Interface Status" of the "Dashboard". The
device connects to the Internet successfully if the "Cellular" icon turns green.
Click the "Cellular" icon to view information such as signal strength, IP address,
and traffic consumption.

14
4.2 Wired Networking
4.2.1 Connect via APP
⚫Step1: Click the "Device" directory below to enter the [Device] page, click the
menu button in the upper right corner, and select [Add Device]. Scan the QR
code on the ODU2002 to add device.

15
⚫After scanning the code successfully, configure the name, serial number, and
description information of the device.
⚫After adding the device, if the device fails to connect to the network, you can
click "Configure local device" to configure the device to connect to the cloud. The
ODU2002 enables the http access and Wi-Fi AP function by default.

16
⚫Scan the QR code on the nameplate of the unit, then the APP will automatically
connect to the ODU via Wi-Fi.
⚫After the connection succeeds, APP will automatically log in to the device and enter
the networking configuration interface, confirm the information then submit.
4.2.1 Configure via PC
⚫Step 1: Connect the LAN1 port to the PC.
⚫Step 2: Set the IP of the PC and the gateway device to be in the same network
segment. DHCP automatically obtains the address (recommended).Use a fixed IP
address. The DHCP server function is enabled by default on the LAN port of the
device, and the PC and the device must be in the same segment. On PC side, the
IP address needs to be configured as any address in 192.168.1.2~192.168.1.254,
the gateway is set to 192.168.1.1, the subnet mask is 255.255.255.0, and the DNS
configuration is 8.8.8.8/operator DNS server address.

17
⚫Step 3: Enter the device default address 192.168.1.1 in the browser address bar,
enter the user name and password (adm/123456 by default), and enter the
device WEB management interface. If the page prompts that the webpage is not
safe, turn on Hidden or Advanced, and choose to continue.
⚫Step 4: Click "Internet" on the left navigation bar to view the device interface
status. ODU2002 enables WAN1 with DHCP mode by default. ODU2002 supports
three methods to allocate WAN address, dynamic DHCP (recommended), static
IP and PPPoE. Click the Edit button next to WAN to modify the WAN port.
⚫DHCP: The DHCP service is enabled by default on the WAN interface of the
device, and the ODU can be connected to the network by connecting the WAN
interface to the Internet with a ethernet cable.
⚫Static IP: User can manually configure the address assigned by the operator or

18
the upstream device. After the configuration is completed, the router will access
the network through the specified static IP.
⚫PPPoE: Users can configure broadband dial-up. After the configuration is
completed, the router will access the network through broadband dial-up.
⚫Step 5: Verify network connectivity Via Ping tool in System/ Tools page.