Innotech IND-GLEIT-10 User manual

IND-GLEIT-10
Instruction manual
© INNOTECH Arbeitsschutz GmbH. Irrtümer, Druckfehler, technische Änderungen vorbehalten! © INNOTECH Arbeitsschutz GmbH. Errors and misprints accepted. We reserve the right to make technical changes.
DE – ACHTUNG: Die Verwendung des INNOTECH-Produkts ist erst zulässig, nachdem die
Gebrauchsanleitung in der jeweiligen Landessprache vollständig gelesen und verstanden wurde.
DE
EN – ATTENTION: Use of the INNOTECH product is only permitted after the instruction
manual has been read and fully understood in the respective language.
EN
IT – ATTENZIONE: L'utilizzo del prodotto INNOTECH è permesso solo previa lettura e
comprensione dell'intero manuale di istruzioni nella lingua del relativo paese di utilizzo.
IT
FR – ATTENTION : L'utilisation du produit INNOTECH n'est autorisée qu'après avoir
entièrement lu et compris la notice d'utilisation dans la langue du pays concerné.
FR
NL – ATTENTIE: Dit INNOTECH-product mag pas gebruikt worden nadat u de gebrui-
kershandleiding in de taal van het betreffende land gelezen en begrepen hebt.
NL
ES – ATENCIÓN: Se autorizará el uso de los productos INNOTECH una vez que se hayan
leído y entendido las instrucciones de uso en el idioma del país.
ES
PT – ATENÇÃO: O uso do produto INNOTECH apenas é permitido depois de ter lido e
compreendido na totalidade as instruções de uso na respetiva língua nacional.
PT
DK – GIV AGT: Du må først bruge et produkt fra Innotech, efter du har læst og forstået
brugsvejledningen i fuldt omfang i dit lands sprog.
DK
SV – O B S : Denna INNOTECH-produkt får inte användas förrän bruksanvisningen på
respektive lands språk har lästs igenom och förståtts.
SV
CZ – POZOR: Práce s výrobkem INNOTECH je povolena teprve po kompletním přečtení a
porozumění návodu k použití v jazyku daného státu.
CZ
PL – UWAGA: Produkty firmy INNOTECH mogą być używane dopiero po dokładnym
zapoznaniu się z całą instrukcją obsługi w ojczystym języku.
PL
SL – POZOR: Uporaba izdelka INNOTECH je dovoljena šele po tem, ko ste navodila preb-
rali v celoti v ustreznem jeziku svoje dežele in jih tudi razumeli.
SL
SK – POZOR: Produkt INNOTECH môžete používať až po prečítaní a porozumení celého
návodu na použitie pre príslušnú krajinu.
SK
HU – FIGYELEM: Az INNOTECH termékek használata csak azt követően engedélyezett,
hogy saját nyelvén elolvasta és megértette a teljes használati utasítást.
HU
TR – DİKKAT: INNOTECH ürününün kullanımına ancak ilgili ülkenin dilinde sunulmuş
olan kullanım kılavuzunun tamamen okunmasından ve anlaşılmasından sonra izin verilir.
TR
ZH – 注意：只有在仔细阅读并完全理解了当地语言的使用说明后，才能使用 INNOTECH 公司的产品。
ZH

2IND-GLEIT-10 / Version 180717 / www.innotech.at
EN
1TABLE OF CONTENTS
[2] EXPLANATION OF ICONS 3
[3] SAFETY INSTRUCTIONS 4
[4] COMPONENTS/MATERIAL 6
[5] PRODUCT SUITABILITY/APPROVAL 6
[6] INSPECTION 7
[7] WARRANTY 8
[8] SIGNS & MARKINGS 9
[9] DIMENSIONS 9
[10] INSTALLATION 10
[11] STORAGE/DISPOSAL 12
[12] DEVELOPMENT & SALES 12

3
EN
IND-GLEIT-10 / Version 180717 / www.innotech.at
2EXPLANATION OF ICONS
Supplementary information/instructions
Warning/danger information
For an IMMEDIATE threat of danger that can cause serious
physical injuries or death.
üCorrect Incorrect
For a POTENTIALLY dangerous situation that can cause serious
physical injuries or death.
For a POTENTIALLY dangerous situation that could lead
to minor physical injuries and damage to property.
DANGER
WARNING
CAUTION
Comply with manufacturerinformation/instruction manual.
Wear gloves!
Wear safety spectacles!

4IND-GLEIT-10 / Version 180717 / www.innotech.at
EN
3SAFETY INSTRUCTIONS
3.1 GENERAL INFORMATION
- The fall protection system may be installed and used only by people who:
• are trained in the use of "personal protective equipment" (PPE),
• are in good physical and mental health. (Medical conditions such as
cardiovascular problems, intake of medicines, consumption of alcohol,
etc. negatively aect the safety of the user.),
• are familiar with the locally applicable safety regulations.
- During installation/use of the fall protection system, the respective accident
prevention regulations (e.g. working on roofs) must be complied with.
-A plan must be available that species rescue procedures for all possible
emergencies.
- Before starting work, ensure that no objects can fall to the ground from the work
site. The area below the work site (pavement, etc.) must be kept clear.
- You should plan, install and use the fall protection system in such a way that no one
can fall over the edge if the personal protective equipment is used properly
(See planning documents at www.innotech.at).
- The fall protection system is subject to maximum limit values. These are found on
the rating plate of the fall protection system, and must not be exceeded.
- When accessing the fall protection system, you must document the positions of the
anchorage devices by means of plans (e.g. top view of the roof).
- After a fall and the resulting strain, you must stop using the fall protection system,
and have it checked by a specialised/competent expert (component parts, fastening
to the substructure, etc.).
- Do not make any changes to the fall protection system.
- If you provide the fall protection system to external contractors, their understanding
of this instruction manual must be conrmed in writing.
- If the fall protection system to sold in other countries, the instruction manual must
be provided in the respective national language.
- Comply with the customary national provisions for lightning protection.
The following safety instructions and the current state of the art must be taken
into consideration.

5
EN
IND-GLEIT-10 / Version 180717 / www.innotech.at
3SAFETY INSTRUCTIONS
3.2 FOR FITTERS: FOR SAFE ASSEMBLY
3.3 FOR USERS: FOR SAFE USE
- Ensure that stainless steel does not get in contact with swarf or steel tools, as this
can lead to corrosion.
- All stainless steel bolts must be greased with a suitable lubricant before installation.
-The tters must ensure that the substructure is suitable for fastening the fall
protection system. If in doubt, consult a structural engineer.
- The roof covering must be properly sealed in accordance with applicable guidelines.
- Document the professional attachment of the fall protection system to the building
structure with dowel logs and photos of each tting situation.
- Attachment to the fall protection system is made by means of INNOTECH sliders
(e.g. IND-GLEIT-10, -11). Use the INNOTECH slider only in combination with the
original carabiner, the INNOTECH "IND" horizontal lifeline system, and personal pro-
tective equipment complying with EN 361 (safety harness) and EN 363 (fall arrest
system).
- The minimum free space necessary under the edge is calculated as follows:
Manufacturer's specication of the personal protective equipment used, including
deection of the cable + body height + 1 m safety margin.
- For horizontal use, only those fasteners may be used that are suited for this purpose
and have been tested for the respective edges (sharp edges, trapezoidal sheets,
steel girders, concrete, etc.).
- Correct use of the individual elements including personal protective equipment
must be ensured, because otherwise the safe functioning of the fall protection
system is NOT guaranteed.
- Do not use fall protection systems if wind speeds exceed normal parameters.
- If used on sloping roofs, roof avalanches (ice, snow) must be avoided by means
of suitable devices to intercept snow.
If uncertainties arise during installation, it is imperative that you contact
the manufacturer.

6IND-GLEIT-10 / Version 180717 / www.innotech.at
EN
4COMPONENTS/MATERIAL
5PRODUCTSUITABILITY/APPROVAL
DANGER TO LIFE from incorrect use.
- Use INNOTECH "IND-GLEIT-10" ONLY for personal safety.
- Use the INNOTECH "IND-GLEIT-10" ONLY in combination with the
• INNOTECH "IND" horizontal lifeline system and
• INNOTECH original carabiners and
• personal protective equipment as per EN 361 (safety harness) and
EN 363 (fall arrest system).
-NEVER hang loads to the INNOTECH "IND-GLEIT-10" which are NOT
expressly approved in this instruction manual.
A) Instruction manual
B) INNOTECH "IND-GLEIT-10": stainless steel, AISI 316
C) INNOTECH "TRIPLE-LOCK CARABINER":stainless steel, AISI 304
!
DANGER
Comply with the manufacturer information for the personal
protective equipment used.
INNOTECH "IND-GLEIT-10" is part of the INNOTECH "IND" horizontal lifeline system; it
is characterised by resistance-free passage along the stainless steel cable, and is used
as a mobile anchorage point for 1 person.
Safety harnesses and lanyard lengths must be matched to the respective structure, and
must satisfy the applicable standards.
Every person working in areas where there is a danger of falling must pay attention
to the fall height.
The connection to the anchorage device must be kept short in order to limit free fall.
B C
A

7
EN
IND-GLEIT-10 / Version 180717 / www.innotech.at
5PRODUCTSUITABILITY/APPROVAL
6.1 TO BE CHECKED BEFORE EACH USE
6INSPECTION
If there are any doubts concerning the reliable operation of the fall
protection system, it must NO longer be used, and must be checked
by an expert (written documentation). If necessary, replace the
product.
DANGER TO LIFE from damage to the INNOTECH "IND-GLEIT-10".
- INNOTECH "IND-GLEIT-10" must be in perfect condition.
- Do NOT continue to use INNOTECH "IND-GLEIT-10" any more if
• Damage or wear to its components is obvious,
• Other defects were observed (loose threaded connections, deformation,
corrosion, wear, etc.),
• Strain has occurred due to a fall,
• The product identication is illegible.
!
DANGER
Before every use, visually inspect INNOTECH "IND-GLEIT-10" for obvious defects.
Check the entire fall protection system's suitability for use by using the acceptance
protocol and test log.
INNOTECH "IND-GLEIT-10" has been tested and certied as per EN 795:2012 TYPES C.
The notified authority participating in the type test:
DEKRA EXAM GmbH, Dinnendahlstrasse 9, D-44809 Bochum, Germany

8IND-GLEIT-10 / Version 180717 / www.innotech.at
EN
7WARRANTY
The warranty period for manufacturing defects on all components (under normal
conditions of use) is 2 years from the date of purchase. The time limit is shortened
through use in corrosive atmospheres.
If there is strain (a fall, weight of snow, etc.,) the warranty claim is void for those
components that have been designed to absorb energy, or that may possibly be
deformed.
For system installation and for components planned and installed
under the responsibility of specialised installation companies,
INNOTECH assumes neither responsibility nor warranty in the case of
improper installation.
The inspection intervals are found in the test log.
6.2 ANNUAL CHECKS
Have INNOTECH "IND-GLEIT-10" inspected at least once each year by a specialist who is
familiar with the fall protection system. The user's safety depends on the eectiveness
and durability of the equipment.
Shorter intervals between inspections may be required, depending on the intensity
of use and the environment (e.g. in corrosive atmospheres, etc.).
Document the verication by the specialist/technician in the INNOTECH "IND" instruction
manual test logs, and keep them in the same place as the instruction manual.
6INSPECTION

9
EN
IND-GLEIT-10 / Version 180717 / www.innotech.at
8SIGNS & MARKINGS
A) Name or logo of the manufacturer/reseller: INNOTECH
B) Type designation: IND-GLEIT-10
C) Signs stating that instructions in the manual
must be followed:
D) Year of manufacture and manufacturer's
serial number: JJJJ-..-...
E) Number of the applicable standard: EN 795:2012 TYPES C
F) Maximum number of people who can be secured: 1
9DIMENSIONS
[mm]
90
166~
31
107
10
O
80
IND-GLEIT-10
Seilgleiter
-..JJJJ -...
EN 795:2012
TYP C
max.
A
B
C
D
E
F

10 IND-GLEIT-10 / Version 180717 / www.innotech.at
EN
10 INSTALLATION
Through vertical movement of both slider halves, place the
"IND-GLEIT-10" onto the "IND-SEIL-40".
1.
2.
DONE!
Close the "IND-GLEIT-10", and lock it using the "TRIPLE-LOCK
CARABINER".

11
EN
IND-GLEIT-10 / Version 180717 / www.innotech.at
10 INSTALLATION
In the closed state, the gap must NOT exceed 6 mm.
≤6 mm

12 IND-GLEIT-10 / Version 180717 / www.innotech.at
EN
11 STORAGE/DISPOSAL
Do NOT dispose the fall protection system in the house waste.
As per national requirements, gather together the used parts, and dispose
of them environmentally correctly.
Keep INNOTECH "IND-GLEIT-10" free of grease, ice, and snow.
Keep INNOTECH "IND-GLEIT-10" together with the personal protective
equipment.
11.1 STORAGE
11.2 WASTE DISPOSAL
12 DEVELOPMENT & SALES
INNOTECH Arbeitsschutz GmbH, Laizing 10, 4656 Kirchham/Austria
www.innotech.at