KLIM Ai-1 Airbag Vest User manual
USER MANUAL
Ai-1 Airbag Vest
Ai-1 Rally Airbag Vest
V2.0 updated 10.2021
USER MANUAL – ENGLISH VERSION
MANUFACTURER NAME AND ADDRESS (A)
KLIM Technical Riding Gear
3753 County Line Road
Rigby, Idaho 83442
United States of America
TYPE OF PRODUCT/NAME OF PRODUCT (B)
Type: Motorcyclist airbag
Name: Ai-1 Airbag Vest
TYPE/INFLATION SYSTEM (C)
Type: Electronic autonomous In&motion airbag
Reference: IMS Moto 1
C: Letter indicating that the garment is a class C, designed
to provide impact protection for areas covered by the impact
protector(s) only and they do not oer complete minimum abrasion
protection and may not oer complete minimum impact protection
U: Letter Indicating Undergarment
EN 17092-6:2020 : Technical Reference Standard
EN 17092-6:2020
C U
USER MANUAL – ENGLISH VERSION
MANUFACTURER NAME AND ADDRESS (A)
KLIM Technical Riding Gear
3753 County Line Road
Rigby, Idaho 83442
United States of America
TYPE OF PRODUCT/NAME OF PRODUCT (B)
Type: Motorcyclist airbag
Name: Ai-1 Airbag Vest
TYPE/INFLATION SYSTEM (C)
Type: Electronic autonomous In&motion airbag
Reference: IMS Moto 1
C: Letter indicating that the garment is a class C, designed
to provide impact protection for areas covered by the impact
protector(s) only and they do not oer complete minimum abrasion
protection and may not oer complete minimum impact protection
U: Letter Indicating Undergarment
EN 17092-6:2020 : Technical Reference Standard
FITTING THE VEST (D)
The vest must be worn and fitted correctly so that the protection
areas are placed on the thorax, abdomen and back. To obtain
optimum protection and comfort, please select the right size and
ensure that the vest is fitted correctly to your body. Close all the
closures and other straps for maximum comfort. If necessary, refer
to the following table to select the appropriate size for your body
shape:
WARNING (E)
Any modification or improper use may negatively impact the
system performance. Do not, under any circumstances, modify
your airbag system, the In&box or its components in any way. Any
modification of any kind may compromise its functionality and
protection capabilities in a fall or accident. Never add decorations,
ribbons, self-adhesive patches, or other parts to the airbag
system. Never connect an electronic device or an external battery
to the system. The vest components must never be modified. This
product should only be serviced/repaired by KLIM to guarantee
the full functionality of this produt. Under no circumstances should
the vest be modified or disassembled.
WARNING (F)
This personal protective equipment (PPE) is intended to protect
against mechanical impacts. In certain cases, it helps reduce the
severity of the injuries to riders and passengers following a fall
to the ground, a collision with a vehicle or an impact against an
obstacle.
There is no product that can oer total protection against injuries,
death, bodily harm, or damage in case of a fall, accident, collision,
impact, loss of control or any other event. Only the parts of the
body covered by the protection may be protected against impact.
The In&motion airbag system can never be considered as a
substitute for protective equipment such as helmets, goggles,
ENGLISH
AIRBAG VEST S M L XL 2XL 3XL
WAIST-SHOULDER
LENGET
37-
42CM
40-
45CM
42-
47CM
42-
47CM
42-
47CM
42-
47CM
gloves, or any other protection device.
There may be weight or ergonomic or heat stress penalties
associated with the use of this product that may be less
inappropriate for some riders.
Warning, the airbag vest is designed to oer optimal protection
only if the airbag system is inflated.
Do not use the garment without its protectors inserted.
This product does not in any way replace any other individual
equipment. Always use your motorcycling garments in
combination with other forms of Personal Protective Equipment
(PPE) including helmets (ECE 22.05) as well as other
corresponding or complementary PPE such as jackets (EN 17092),
trousers (EN 17092), other impact protectors (EN 1621), boots
(EN 13634), gloves (EN 13594), visibility clothing (EN 1150) or high
visibility accessories (EN 13356) in order to optimise the protection
of your body against any risk likely to occur when riding.
“OPERATING A MOTORCYCLE AND RACING ARE INHERENTLY
DANGEROUS ACTIVITIES THAT CAN RESULT IN DEATH, BRAIN
DAMAGE, PARALYSIS OR SERIOUS PERSONAL INJURY. YOU
ASSUME THE RISK OF INJURY OR DEATH WHENEVER YOU ARE
OPERATING A MOTORCYCLE. The In&box and associated airbag
system are designed to reduce certain of those risks in defined
conditions, but they cannot eliminate all risks or insure against
injury or death even in situations where the system performs as
intended.
Further, excessive speed or other violation of trac laws or user
error can result in accident situations beyond the capacity of the
system to minimize or eliminate the risks of injury.
WARNINGS AND USE LIMITATIONS
NO PROTECTIVE GARMENTS CAN OFFER COMPLETE
PROTECTION AGAINST ALL INJURIES!
Always use your motorcycling garments in combination with
other PPE, including helmets, and other corresponding or
complementary PPE garments such as jackets, trousers, impact
protectors, boots, eye protection and gloves.
• Motorcycling is an INHERENTLY DANGEROUS ACTIVITY:
wearing protective equipment should not be an excuse for
increasing readiness to take risks
• Do not use the protective vest for other uses: improper handling
may seriously reduce the protection provided.
There is no product (neither PPE nor PPE combinations) that can
oer total protection against injuries or death.
WARNING: do not use YOUR GARMENT without its PROTECTORS
inserted!
IF YOU DO NOT UNDERSTAND OR APPRECIATE THE
DANGER OF THESE ACTIVITIES, PLEASE REFRAIN FROM ALL
MOTORSPORTS ACTIVITY AND FURTHER USE OF IN&MOTION
AIRBAG SYSTEM.
TEMPERATURE LIMITATIONS (G)
The system must be used exclusively at temperatures between
-10°C and 45°C (14°F and 113°F). Prolonged exposure of the
system to temperatures exceeding this range may compromise its
functionality.
CLEANING INSTRUCTIONS (H)
Do not wet the back protector or the back of your item. The inflator
connector, the inflator, the In&box must not encounter water.
Clean the exterior and interior of your item with soapy water using
a small soft brush and by gently scrubbing in a circular motion.
Then rinse with a soft wet sponge to remove the excess soap and
any dirt that you may have loosened in the previous step. Dry your
item first by using a soft cotton cloth; then leave to completely air
dry in a dry and ventilated area for a minimum of 12 hours.
• Do not bleach
• Do not iron
• Do not machine wash
• Do not dry clean
• Do not tumble dry
• Do not use a hair dryer
• Do not use detergent
• Dry away from sources of heat and away from sunlight
WARNING (I)
The airbag vest is designed to oer optimal protection only if the
airbag system is inflated.
STORAGE AND TRANSPORTATION (J)
Keep the vest and the In&box in a clean and ventilated area, away
from humidity and light, and away from impacts and pressure. Do
• Do not use the protective vest for other uses: improper handling
may seriously reduce the protection provided.
There is no product (neither PPE nor PPE combinations) that can
oer total protection against injuries or death.
WARNING: do not use YOUR GARMENT without its PROTECTORS
inserted!
IF YOU DO NOT UNDERSTAND OR APPRECIATE THE
DANGER OF THESE ACTIVITIES, PLEASE REFRAIN FROM ALL
MOTORSPORTS ACTIVITY AND FURTHER USE OF IN&MOTION
AIRBAG SYSTEM.
TEMPERATURE LIMITATIONS (G)
The system must be used exclusively at temperatures between
-10°C and 45°C (14°F and 113°F). Prolonged exposure of the
system to temperatures exceeding this range may compromise its
functionality.
CLEANING INSTRUCTIONS (H)
Do not wet the back protector or the back of your item. The inflator
connector, the inflator, the In&box must not encounter water.
Clean the exterior and interior of your item with soapy water using
a small soft brush and by gently scrubbing in a circular motion.
Then rinse with a soft wet sponge to remove the excess soap and
any dirt that you may have loosened in the previous step. Dry your
item first by using a soft cotton cloth; then leave to completely air
dry in a dry and ventilated area for a minimum of 12 hours.
• Do not bleach
• Do not iron
• Do not machine wash
• Do not dry clean
• Do not tumble dry
• Do not use a hair dryer
• Do not use detergent
• Dry away from sources of heat and away from sunlight
WARNING (I)
The airbag vest is designed to oer optimal protection only if the
airbag system is inflated.
STORAGE AND TRANSPORTATION (J)
Keep the vest and the In&box in a clean and ventilated area, away
from humidity and light, and away from impacts and pressure. Do
not store the vest and the In&box near combustible surfaces or
objects. Do not leave the vest exposed to direct sunlight, under a
windscreen, store in a car, or in a top case.
Do not fold, crease, bend, twist, or ball up the vest. Hang it on
a hanger or in a completely flat position to avoid any rupture or
breakage.
Transport the vest in clean packaging protecting it from humidity
and direct sunlight.
Make sure to turn your In&box o when using any other
transportation (car, bus, airplane, train or using a motorcycle but
not wearing the airbag system) and keep this user manual for as
long as you have the vest and transfer the user manual to any
subsequent owner of the vest. Furthermore, keep this user manual
with the product when travelling, notably by airplane. If it is used
incorrectly, the vest may cause an unsuitable inflation, which
could damage your belongings or even create a safety risk for
other people. On the In&motion site www.inemotion.com you will
find the necessary documents to facilitate the transport of your
product. In&motion cannot be held liable in the event an airline
refuses to transport the product by airplane.
PRODUCT INSPECTION (K)
After an impact, the back protector, the airbag system and in
particular the airbag cushion, may be partially damaged by having
absorbed the energy from the impact to reduce its force.
Time can also partially damage your product. Systematically
before every use check visually your protection equipment to
confirm that it is in good useable condition and not damaged:
• No fabric deterioration (excessive bubbling, snags, fraying
seams, broken seams, over-stitching)
• No deterioration of the plastic parts (fissures, cracking,
whitening).
“This product should only be serviced/repaired by KLIM to
guarantee the full functionality of this product. Under no
circumstances should the vest be modified or disassembled.”
“Follow local regulations for recycling/discarding the vest and
back protector.”
The vest life cycle is variable. It depends on the frequency and
conditions of use. Used and maintained correctly, the vest is
guaranteed 2 years starting from the date of purchase. After that,
if you have any suspicion, you can have your airbag vest controlled
by KLIM.
It has been designed to withstand 3 inflations without mandatory
return to the manufacturer [www.KLIM.com] for inspection,
provided that the post- inflation inspection procedure is always
respected. After having endured 3 inflations, the airbag vest may
function improperly.
PROTECTIVE PRODUCT COMPATABILITY (L)
SEE “JACKET COMPATABILITY”
INFLATOR TYPE (M)
SEE “INFLATOR REPLACEMENT”
DESCRIPTION OF COMPONENTS (N)
AIRBAG VEST:
Vest integrating the In&motion airbag
system. Ai-1 Airbag Vest 3046-000
IN&BOX:
Airbag system detection and triggering
device containing sensors and the
battery. (see the In&box user manual,
provided with the In&box)
The In&box is an electronic device placed
in the shell. It is provided with an USB
cable and its own user manual. Each
In&box has a unique identifier linked
to a user account. Before using your
In&box, please read carefully the detailed
instructions in the In&motion specific user
manual dedicated to the In&box use.
INFLATOR: GAS GENERATOR
The inflator is a gas generator. USE ONLY
WITH THE IN&MOTION AIRBAG SYSTEM.
Warning! Handle with care. This generator
is filled with high pressure gas. Store at a
temperature less than 45°C (113°F).
Do not repair, do not pierce, do not reload, do not disassemble,
do not use with any other electronic equipment, users must be
18 and over to manipulate the Inflator. If the inflator shows signs
of damage, please send it to In&motion [www.inemotion.com] for
recycling. The inflator expiration date is indicated on the label. Do
provided that the post- inflation inspection procedure is always
respected. After having endured 3 inflations, the airbag vest may
function improperly.
PROTECTIVE PRODUCT COMPATABILITY (L)
SEE “JACKET COMPATABILITY”
INFLATOR TYPE (M)
SEE “INFLATOR REPLACEMENT”
DESCRIPTION OF COMPONENTS (N)
AIRBAG VEST:
Vest integrating the In&motion airbag
system. Ai-1 Airbag Vest 3046-000
IN&BOX:
Airbag system detection and triggering
device containing sensors and the
battery. (see the In&box user manual,
provided with the In&box)
The In&box is an electronic device placed
in the shell. It is provided with an USB
cable and its own user manual. Each
In&box has a unique identifier linked
to a user account. Before using your
In&box, please read carefully the detailed
instructions in the In&motion specific user
manual dedicated to the In&box use.
INFLATOR: GAS GENERATOR
The inflator is a gas generator. USE ONLY
WITH THE IN&MOTION AIRBAG SYSTEM.
Warning! Handle with care. This generator
is filled with high pressure gas. Store at a
temperature less than 45°C (113°F).
Do not repair, do not pierce, do not reload, do not disassemble,
do not use with any other electronic equipment, users must be
18 and over to manipulate the Inflator. If the inflator shows signs
of damage, please send it to In&motion [www.inemotion.com] for
recycling. The inflator expiration date is indicated on the label. Do
not discard a full inflator (that has never been triggered). In the
event your inflator has surpassed its life expectancy (4 years for
expiry date as printed on the label) you are required to recycle
this inflator as a full inflator is never to be disgarded as it must
be recyled. Please contact In&Motion at www.inemotion.com
for further recycling details. Check if the inflator is full or empty:
• Screw the inflator into the In&motion airbag system • Plug the
connector into the inflator
• Insert the running In&box into its housing
If the inflator LED (light indicator) is solid green, the
inflator is full and connected.
If the inflator LED (light indicator) is solid red, the inflator
is empty and/or improperly connected.
BACK PROTECTOR:
The vest contains a back protector certified EN
1621-2:2014. The In&motion back protector has been
designed specifically for two-wheeled motor vehicle
users and must be used exclusively in association with
the In&motion airbag system.
Ai-1 airbag vest contains a IMP Moto 1 back protector.
You will find its user manual on page xxx of this manual.
Ai- 1 Rally Vest contains a D3O back
and chest protector. See the D3O
user manual provided with the D3O
back and chest protector.
INFLATOR REPLACEMENT (O)
Warning! Do not touch the full inflator connector with your fingers
(blue piece on the bottom of the inflator). Do not connect the
inflator connector to the inflator before having screwed it on the
cushion.
1. Replacing the inflator
Warning, inflators are for single-use. After an inflation, it cannot
be refilled and must be changed. Only inflators provided by
In&motion (ref: IMI 2368) are certified and designed for use in the
In&motion airbag system. Do not use any other inflators for any
reason.
To obtain a new inflator, contact your local reseller.
2.Post-inflation procedure
After inflation, please follow the following 4 steps:
1) Check the integrity of the vest
2) Remove the empty inflator
3) Check the integrity of the In&motion airbag system
4) Install a new inflator
These steps are described below. In case of damage or anomaly,
do not use the vest and contact your local reseller.
You will also find this procedure on In&motion tutorial video
available on In&motion Youtube channel:
http://bit.ly/InemotionTuto as well as in the mobile app «My
In&box».
3. Check the integrity of your vest
Check the integrity of the fabric parts and plastic
parts. Check the integrity of the back protector.
Check the integrity of the connector. If you suspect
any deterioration in the vest (abrasion, holes, rips
in the fabrics parts or plastic parts, breakage or
whitening of the plastic parts, fabric bobbling,
rupture of the vest assembly threads), contact your
local reseller.
4. Remove the empty inflator
Warning!
The inflator must be handled carefully
Wash your hands before and after
replacing the inflator. Conduct the
following operations in a clean and dry
environment.
Remove the In&box from its housing.
In&motion (ref: IMI 2368) are certified and designed for use in the
In&motion airbag system. Do not use any other inflators for any
reason.
To obtain a new inflator, contact your local reseller.
2.Post-inflation procedure
After inflation, please follow the following 4 steps:
1) Check the integrity of the vest
2) Remove the empty inflator
3) Check the integrity of the In&motion airbag system
4) Install a new inflator
These steps are described below. In case of damage or anomaly,
do not use the vest and contact your local reseller.
You will also find this procedure on In&motion tutorial video
available on In&motion Youtube channel:
http://bit.ly/InemotionTuto as well as in the mobile app «My
In&box».
3. Check the integrity of your vest
Check the integrity of the fabric parts and plastic
parts. Check the integrity of the back protector.
Check the integrity of the connector. If you suspect
any deterioration in the vest (abrasion, holes, rips
in the fabrics parts or plastic parts, breakage or
whitening of the plastic parts, fabric bobbling,
rupture of the vest assembly threads), contact your
local reseller.
4. Remove the empty inflator
Warning!
The inflator must be handled carefully
Wash your hands before and after
replacing the inflator. Conduct the
following operations in a clean and dry
environment.
Remove the In&box from its housing.
12
Open the zipper on the back to access the inflator.
Unclip the inflator from its housing.
To do this, pull the inflator to remove it from its housing.
Warning! To avoid damage, do not force the connector and do not
pull on the cable to remove the inflator.
Press the two tabs and then pull gently. If it’s not easy, press on
one connector tab, then the other and so on.
Unscrew the used inflator only after removing the
connector.
Check that the seal is positioned correctly and is not
damaged.
5. Check the integrity of the In&motion airbag
system
Take your inflation adapter, which is provided with
your spare inflator. To purchase a new inflator, you
can go on www.inemotion.com or in shops.
Screw the provided inflation adapter in the
place of the inflator.
Thanks to this adapter and using a pump or a
compressor, inflate the vest to 0,3 bar (5 psi)
and check that it does not deflate in less than 5
seconds. (Any pneumatic inflation system, such
as those available in filling stations may be
suitable for this operation.).
While the vest is inflated, check the integrity
of the fabric parts and seams. Check that the
seams are not fraying. If the vest does not
inflate or deflates quickly, do not use the vest
and contact your local reseller. Otherwise,
remove the adapter by unscrewing it, then
completely remove the air contained in the
airbag system.
6. Install a new inflator
Warning! Do not touch the full inflator connector with your fingers
(blue piece on the bottom of the inflator). Do not connect before
having screwed on the inflator.
Warning! Before carrying out the following
steps, check that the airbag system is
completely void of air.
Screw on the new inflator hand tight.
Plug the connector back in.
Check that it is properly clipped all the way.
Clip the inflator into its housing.
Check that the inflator is correctly positioned,
fully seated in its housing.
Close the zipper to the top.
To check that the inflator is new and properly
connected, take the In&box, put it on and insert in its
housing. The inflator LED should switch to green.
6. Install a new inflator
Warning! Do not touch the full inflator connector with your fingers
(blue piece on the bottom of the inflator). Do not connect before
having screwed on the inflator.
Warning! Before carrying out the following
steps, check that the airbag system is
completely void of air.
Screw on the new inflator hand tight.
Plug the connector back in.
Check that it is properly clipped all the way.
Clip the inflator into its housing.
Check that the inflator is correctly positioned,
fully seated in its housing.
Close the zipper to the top.
To check that the inflator is new and properly
connected, take the In&box, put it on and insert in its
housing. The inflator LED should switch to green.
USING THE IN&BOX (P)
To start:
For the first use of your
product, please read
the detailed In&box
user instructions in the
In&motion user manual, provided with the In&box.
Insert your In&Box into position.
The arrows indicated on the In&box lock open (up and down) must
be aligned with the INSERT arrows indicated on the shell.
Using the lock, push the In&box to the left side to clip it into place.
The arrows indicated on the In&box lock closed must be aligned
with the INSERT arrows indicated on the shell.
Warning! Make sure the red locked marking is not visible.
4. WARNING
The vest textile is not abrasion resistant. Therefore, it is imperative
that your jacket or coat designed for use with two-wheeled motor
vehicles completely covers the vest.
Warning: excessive exposure to water will cause the airbag
product to function improperly. It is recommended for use only
under a waterproof protection garment designed for two-wheeled
motor vehicle users. Under no circumstances should the vest be
worn alone, without a protective coat or jacket over it because the
vest textile is not resistant to abrasion.
JACKET COMPATIBILITY (Q)
The In&motion airbag system is compatible with
a backpack. For that, it is important to respect the
following conditions:
• The total weight of the bag must not exceed 8kg,
• The use of support straps in the abdomen and
chest is prohibited,
• The shoulder straps must not hinder the
deployment of the airbag. When pulling the straps
forward, there should be a distance of 10 cm between them and
the front of the shoulder.
• The backpack must be worn on the back of the user’s body,
compatible with a compatible motorcycle jacket.
4. WARNING
The vest textile is not abrasion resistant. Therefore, it is imperative
that your jacket or coat designed for use with two-wheeled motor
vehicles completely covers the vest.
Warning: excessive exposure to water will cause the airbag
product to function improperly. It is recommended for use only
under a waterproof protection garment designed for two-wheeled
motor vehicle users. Under no circumstances should the vest be
worn alone, without a protective coat or jacket over it because the
vest textile is not resistant to abrasion.
JACKET COMPATIBILITY (Q)
The In&motion airbag system is compatible with
a backpack. For that, it is important to respect the
following conditions:
• The total weight of the bag must not exceed 8kg,
• The use of support straps in the abdomen and
chest is prohibited,
• The shoulder straps must not hinder the
deployment of the airbag. When pulling the straps
forward, there should be a distance of 10 cm between them and
the front of the shoulder.
• The backpack must be worn on the back of the user’s body,
compatible with a compatible motorcycle jacket.
In&Box Inserted
Correctly
In&Box Inserted
Incorrectly
In&Box Inserted
Incorrectly
The airbag product is not compatible child harness.
The airbag product is not compatible with jackets or coats having
a support in the crotch.
Never wear a neckbrace while wearing the airbag system. The
airbag system is not compatible with a neckbrace.
Do not zip your jacket to your trousers.
The vest is not compatible with full one-piece suit (for instance
textile/leather suit, rain suit) except “In&motion Airbag system
compatible” suits which have been tested and are compatible
with a proper inflation of the airbag, provided that the size of the
garment is appropriate to your body dimensions.
To select the proper size of your garment, please refer to the
sizing guide of the garment.
The use of the vest with non-compatible suit may cause the airbag
to function improperly and can cause injury.
USE RECOMMENDATION (R)
Warning! Excessive exposure to water
will cause the vest to function improperly.
It is recommended for use only under a
waterproof protection garment designed
for two-wheeled motor vehicle users.
The vest textile is not abrasion resistant.
Therefore, it is imperative that your jacket
or coat designed for use with two-wheeled
motor vehicles completely covers the vest.
To verify that your jacket on your body
is compatible with the airbag vest,
measurements must be taken. You can
check the compatibility of your jacket or
vest yourself by following the protocol
below:
1) Measurements of the user without vest
Take the following measurements without
wearing the vest:
A) Measure around your chest in cm | in inches (e.g. 100 cm | 39
inches)
B) Measure around your waist, at navel height, in cm | in inches
(e.g. 90 cm | 35 inches)
C) Add these 2 measurements, then divide by 2
The airbag product is not compatible child harness.
The airbag product is not compatible with jackets or coats having
a support in the crotch.
Never wear a neckbrace while wearing the airbag system. The
airbag system is not compatible with a neckbrace.
Do not zip your jacket to your trousers.
The vest is not compatible with full one-piece suit (for instance
textile/leather suit, rain suit) except “In&motion Airbag system
compatible” suits which have been tested and are compatible
with a proper inflation of the airbag, provided that the size of the
garment is appropriate to your body dimensions.
To select the proper size of your garment, please refer to the
sizing guide of the garment.
The use of the vest with non-compatible suit may cause the airbag
to function improperly and can cause injury.
USE RECOMMENDATION (R)
Warning! Excessive exposure to water
will cause the vest to function improperly.
It is recommended for use only under a
waterproof protection garment designed
for two-wheeled motor vehicle users.
The vest textile is not abrasion resistant.
Therefore, it is imperative that your jacket
or coat designed for use with two-wheeled
motor vehicles completely covers the vest.
To verify that your jacket on your body
is compatible with the airbag vest,
measurements must be taken. You can
check the compatibility of your jacket or
vest yourself by following the protocol
below:
1) Measurements of the user without vest
Take the following measurements without
wearing the vest:
A) Measure around your chest in cm | in inches (e.g. 100 cm | 39
inches)
B) Measure around your waist, at navel height, in cm | in inches
(e.g. 90 cm | 35 inches)
C) Add these 2 measurements, then divide by 2
(e.g. 100+90=190 and 190/2=95 cm | 39+35=74 and 74/2=37
inches)
2) Measurements of your jacket or coat
The following measurements are taken while stretching the jacket.
All the elastic fabrics and elasticated parts in the direction of
measurement taking must be fully stretched. Place your closed
jacket on a flat surface.
A) While stretching the jacket until the elasticated parts and fabrics
are taut, measure the width of the jacket under the armpits in cm
(e.g. 58cm | 22 inches)
B) In the same way, while stretching the jacket fully, measure the
width of the jacket at navel level in cm (e.g. 52cm | 20 inches)
C) Add these 2 measurements (e.g. 58+52=110 cm | 22+20=42
inches)
Your jacket is compatible with the vest if the dierence between
the first (95cm | 37 inches) and the second result obtained in C
(110cm | 42 inches) is greater than or equal to 13cm | 5.2 inches.
If you are not sure, ask your local reseller for advice.
Example: 110-95=15cm | 42-37=5 inches... your jacket is
compatible.
If your jacket is not compatible, do not use the airbag vest with
your jacket. Wearing the airbag vest in such a case may cause the
airbag to function improperly and can cause injury.
If you need help figuring out sizing, contact KLIM customer
service.
NOTIFIED BODY, ADDRESS AND LABRATORY CE NUMBER (S)
The product has been tested according to
CRITT protocol AMC-012 and EN17092-6: 2020
Notified body Aliénor Certification n°2754
ZA du Sanital
21 Rue Albert Einstein
86100 CHATELLERAULT
FRANCE
PRODUCTION YEAR OR SERIAL NUMBER (T)
Production year 2019
EXPIRATION DATE OF ITEMS (U)
Refer to section (N)
STANDARD USED (V)
Vest certified according to experts by the notified body Alienor
Certification n° 2754
REGULATION (W)
The CE marking indicates that the protector conforms to the
regulatory requirements of EU 2016/425.
DECLARATION OF CONFORMITY (X)
www.inemotion.com or KLIM website. The EU declarations of
conformity can be accessed at the following URL: www.KLIM.com/
eu-doc.
RISK ANALYSIS [Y]
Over the last 15 years, data stemming from accident and trauma
studies of two-wheeled motor vehicle users shows that during
serious accidents, injuries are statistically concentrated at the
thorax, abdomen, and spinal column. Among users injured on two-
wheeled motor vehicles, 17% are considered very serious injuries,
of which 75% aect the thorax (Source: ONISR – January 2015).
The airbag vest is not designed to protect your lower limbs, upper
limbs, head.
DETECTION CONDITIONS [Z]
User safety is In&motion’s primary concern.
As part of our obligation of means, we strive to implement all the
technological solutions that we have available so that the In&box
detection system can oer the best degree of protection and
comfort.
However, the user of this protection system is responsible for
his/her protection, and this system is developed by In&motion to
provide optimal protection only during responsible and respectful
behavior on the road. In&motion does not guarantee the absence
of damage. The In&motion airbag system cannot make up for
behaviour that is dangerous, or in conflict with road safety
regulations.
Details regarding detection and deployment of the airbag can be
found in the In&box user manual.
For the airbag to function properly, the user must check the
following items before each use:
The inflator present in the airbag system is filled and connected
properly; the LEDS on the In&box held check the inflator status,
see the In&box User Manual (“LEDS meaning”)
The inflator present in the airbag system is always usable; the
inflator expiration date is indicated on the label on the inflator;
If the airbag vest has already been inflated, the user has correctly
followed the procedure in this user manual (“After an inflation”).
The In&motion detection system evolves over time and the
detection algorithms may be updated thanks to the collection
of anonymous user data. Thus, applicable detection conditions
at a given date are indicated in the In&box user manual to be
downloaded from In&motion’s company website (www.inemotion.
com). In order to get the latest updated version of the In&box user
manual, please refer to the support section in the www.inemotion.
com website.
AIR BAG VEST CONCEPT
The In&motion airbag system function sin 3 steps:
Detect: With 1000 analyzes/second, the In&box measures the
user’s every movements to detect a loss of balance.
According to the kind of fall or accident, the airbag may not
deploy. Everything that is related to the detection strategy is under
In&motion responsability. Should you need more information
about the dierent scenarios, please contact I&Motion on
Protect: In less than 60 milliseconds, the airbag is inflated at the
optimum pressure, protecting the user from impacts.
Perfect: Continous evolutions for a better protection. The system
sends data for analyse to In&motion. A better understanding of
unusual situations or unconventional uses allow us to upgrade the
system. It will better predict falls thanks to algorithme evolutions.
WARNING:
The vest must not be used by people wearing a pacemaker or
any other implanted medical devise, or who have a history of
cardiac problems. Use of the vest is not recommended for persons
who have back or neck problems. The vest must not be used by
persons who have breast protheses. The vest must not be used
by pregnant women. Any piercing present in the area covered by
the vest must be removed. Do not carry any sharp objects (such as
key, knife, screwdriver) in your jacket that may damage the airbag
cushion.
The degree of risk or hazard that a motorcyclist will face is closely
linked to the type of riding and the nature of the accident. Riders
are cautioned to carefully choose motorcyclists’ protective
garments that match their riding activity and risks. Other garments
or garment combinations certified according to the EN 17092
series of standards may provide more appropriate protection than
this garment but there may be weight or ergonomic (e.g. range of
motion restrictions) or heat stress penalties associated with their
use, that may be less appropriate for some riders.
This PPE garment is designed to provide impact protection for the
areas covered by the impact protector(s). It does not oer abrasion
protection.
TROUBLESHOOTING
If you have a problem concerning the vest, the airbag system or
you do not know where the problem is coming from, contact your
local reseller.
If you have a problem concerning the In&box, contact In&motion
customer service via the contact form in the contact section of the
www.inemotion.com website.
BACK PROTECTOR USE INSTRUCTIONS
The IMP Moto back and the IMP back 1 protector was designed
especially for motorcyclists.
1 INTENDED USE
The IMP Moto back and the IMP back 1 protector was designed
to be used uniquely on motorbikes. Do not use for any other
application (skiing, skating, horseback riding, cycling, etc.) The
back protector protects against impacts with the ground or
an obstacle during an accident. It may reduce injury severity
(contusions or fractures). No product or protection system can
oer total protection against injuries or damages to an individual
or an asset in the event of fall, collision, impact, loss of control, or
other. Likewise, this back protector may not totally prevent injuries
to the spinal column. The back protector does not oer protection
against the risks of perforation, cut or penetration of an object.
Use of this product must not encourage exceeding any limits or
taking additional risks.
2 SIZING SELECTION
Refer to the table below to choose your size:
Selecting a protector that is too large may lead to a risk of
interference with the helmet, causing dangerous driving
conditions.
3 Fit instructions
The IMP moto back 1 and the IMP moto back protector must
be correctly fitted and worn, in order to eectively protect the
protection areas. To obtain optimum protection and comfort,
please select the right size and ensure that the airbag product is
fitted correctly to your body. Close all of the closures (zip closures),
Back protector Size 1 Size 2 Size 3
Waist-shoulder
length
37-42 cm 40-45cm 42-47cm
and other straps for maximum comfort. The IMP back 1 protector is
compatible with pocket of size 25*46 for size 1, 26*48cm for size 2
and 28*50cm for size 3.
4 MINIMUM DIMENSIONS IN THE PROTECTION AREAS
Figure 1 - Full back protector
Dimensions of the minimum
protection area on the back
protector
5 Level of protection
The protection areas of this product have been tested and
certified in accordance with the standard EN1621-2:2014. The table
below indicates the values of average residual force for the two
levels of protection defined by standard.
6 EXPLANATION OF THE MARKING
The CE marking indicates that the impact protector is conform to
regulatory requirements EU 2016/425.
Name of the back protector
CE : Symbol of European conformity
Pictogram indicating exclusive motorcycle use of the protection
Dimensions of Figure 1
A B C D E F
72% 29% 44% 29% 32% 25%
NOTE: All dimensions are related to the
waist-shoulder length (100%) of the
largest user.
LEVEL* AVERAGE TOTAL
VALUE
INDIVIDUAL VALUE
1≤18W KN ≤24 KN
2≤9 KN ≤12 KN
Other manuals for Ai-1 Airbag Vest
1
Table of contents
Languages:
Other KLIM Safety Equipment manuals
