Innova Well Seeker PRO User manual

Doc #: IDI06-11P
Rev: 1.1
Issued: 04/09/19
Page 1 of 8
Well Seeker PRO
Toolbars How to Guide
Rev 1.1

Doc #: IDI06-11P
Rev: 1.1
Issued: 04/09/19
Page 2 of 8
Contents
1.0 - Introduction .................................................................................................................................... 3
2.0 - Show and Hide Toolbars ................................................................................................................. 4
3.0 - Removing Icons from a Toolbar ...................................................................................................... 5
4.0 - Adding Icons to a Toolbar ............................................................................................................... 6
5.0 - Resetting a Toolbar to Default ........................................................................................................ 8

Doc #: IDI06-11P
Rev: 1.1
Issued: 04/09/19
Page 3 of 8
1.0 - Introduction
Well Seeker Pro comes pre-installed with three toolbars:
 A Well Seeker Toolbar which contains the main functions of Well Seeker
 A Reporting Toolbar, which contains functions relating to the Drill String and Daily Reporting
editors.
 A Field Toolbar, which contains functions that Directional Drillers commonly use during
drilling operations.
This document provides a guide to customizing the Well Seeker and Reporting toolbars.

Doc #: IDI06-11P
Rev: 1.1
Issued: 04/09/19
Page 4 of 8
2.0 - Show and Hide Toolbars
It is possible to hide or display both toolbars based on the user’s personal preference. The selection
made is remembered by Well Seeker and the selected toolbars will be displayed each time the
software is opened. The user can show or hide the toolbars by following the below steps:
1. Open the View menu from the Menu Bar and select the Toolbars and Docking Windows menu
item.
2. Select the Well Seeker Toolbar, Reporting Toolbar or Field Toolbar item to toggle the respective
toolbars on/off.

Doc #: IDI06-11P
Rev: 1.1
Issued: 04/09/19
Page 5 of 8
3.0 - Removing Icons from a Toolbar
When first installed, the toolbar contains all the available options, which for some users may be too
many buttons. It is possible to remove any unwanted icons by following the below step:
1. Hold down the ALT key and then left-click the mouse key and drag the desired icon away from
the toolbar. Releasing the mouse key will then cause the icon to disappear.

Doc #: IDI06-11P
Rev: 1.1
Issued: 04/09/19
Page 6 of 8
4.0 - Adding Icons to a Toolbar
If an icon is removed by mistake, or if the user decides to add back in previously removed icons, this
can be achieved by following the below steps:
1. Open the View menu from the Menu Bar and select the Toolbars and Docking Windows menu
item.
2. Select the Customize menu item to open the Customize dialog. Select the Commands tab.
3. The user can then search for the desired icon by selecting the various categories on the left-hand
side of the dialog. The icons relating to the selected category will be displayed in the Commands
box on the right-hand side of the dialog.

Doc #: IDI06-11P
Rev: 1.1
Issued: 04/09/19
Page 7 of 8
4. Once the desired icon has been identified, it can be added to the toolbar by dragging and
dropping it onto the toolbar.

Doc #: IDI06-11P
Rev: 1.1
Issued: 04/09/19
Page 8 of 8
5.0 - Resetting a Toolbar to Default
The toolbar can be reset back to its default setting, as per first install as follows:
1. Open the View menu from the Menu Bar and select the Toolbars and Docking Windows menu
item.
2. Select the Customize menu item to open the Customize dialog. Select the Toolbars tab.
3. Select your desired toolbar and click on the Reset button. Alternatively click on the Reset All
button to reset all the toolbars.