Innova C01R2W User manual

1-11
CONTENTS
Advisory
Setup and Installation
Wireless Hand Control
year Warranty1-2-20
Adjustable Base
C01R2W Wireless
Owner Manual

11-11
WARNING
Attention: Read the following information
before using this product . Failure to use a
surge protection device could compromise
safety or cause product malfunction and could
void the electrical portion of your warranty.
- Electrical surges are by far the biggest cause of problems with
electrical circuits.
In order to help protect your investment in case of a power surge or
outage, use an electrical surge protection device (not included).
WARRANTY WARNING!
Do not open or tamper with the transformer, control box, motors, or
remote control (with the exception of battery compartments). The
product warranty will be void if these components are tampered
with.
SMALL CHILDREN AND PETS:
Immediately dispose of all packing materials as they can smother
small children and pets. Do not allow any persons or pets under the
bed. Children, convalescents and disabled person should not operate
the bed without adult supervision.
HOSPITAL OR CONVALESCENT USE DISCLAIMER:
Adjustable beds are designed and engineered for a life style of
in-home comfort and are not intended for hospital use or for a
bed-ridden patient on an extended recovery. Adjustable beds are not
equipped with bars to help patients get safely in and out of bed and
are not intended to be used around tent type oxygen therapy or
explosive gases.
2-11
this warranty; (d) to damage to mattresses, fabric, cables,
electrical cords or items supplied by dealers. Contact the
dealer for warranty information on these items; (e) if there
has been any modification of the adjustable bed without prior
written consent by Innova; (f) to costs for unnecessary service
calls, including costs for in-home service calls solely for the
purpose of education the consumer about the adjustable bed
or finding an unsatisfactory power connection; (g) if the
recommended weight restriction is not followed (refer to the
advisory section of this manual), the warranty will be void.
Repairs to or replacement of an adjustable bed or its
components under the terms of this limited warranty will
apply to the original warranty period and will not serve to
extend such period. The decision to repair or to replace defective
parts under this warranty shall be made, or cause to be made, by
INNOVA at its option and in its sole discretion. Repair or
replacement shall be the sole remedy of the purchaser. There
shall be no liability on the part of Innova for any special, indirect,
incidental, or consequential damages or for any other damage,
claim, or loss not expressly covered by the terms of this
warranty. This limited warranty does not include
reimbursement for inconvenience, removal, installation, setup
time, loss of use, shipping, or any other costs of expenses,
Innova and/or its service technicians shall not be responsible for
moving furniture or any other items not attached to the
adjustable bed in order to perform service on the adjustable
bed. It is the sole responsibility of the purchaser to provide
adequate space and accessibility to the adjustable bed. In the
event that the technician is unable to perform service due to lack
of accessibility, the service call will be billed to the purchaser
and the service will have to be rescheduled. Innova makes no
other warranty whether expressed or implied, and all implied
warranties of merchantability and fitness for a particular
purpose are disclaimed by Innova and excluded from this
agreement. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation
or exclusion may not apply to every purchaser. This warranty
gives the purchaser specific legal rights, and the purchaser may
also have other rights, which may vary from state to state. This
warranty is valid in all 50 states, Puerto Rico, and Canada.

3-11
10-11
PRODUCT RATINGS:
The bed lift motors are not designed for continuous use of more than
2 minutes in an 18 minutes period, or approximately 10% duty cycle.
Any attempt to circumvent or exceed this rating will shorten the
life expectancy of the product and may void the warranty.
WEIGHT UNITS:
The limitation for this adjustable bed is 750 lbs. The bed will
structurally support these weights, provided it is evenly distributed
across the head and foot sections. This product is not designed to
support or lift this amount in the head or foot section alone.
Exceeding this weight restriction could damage the bed and/or
cause injury and void the warranty. Enter or exit the bed in a flat
position and do not sit on the head or foot sections while in the raised
position.
LIFTING AND LOWERING MECHANISMS :
It is normal for the raising and lowering feature on this bed to emit
a minimal humming sound during operation.
LOCATION ENVIRONMENT:
The level of sound experienced in a room is directly related to the
environment within that location. In a room with hardwood floors
and the massagers turned on, a vibrating noise can be noticeable. To
reduce the resonance, place a piece of carpet or rubber casters cups
under the legs. The rubber caster cups also prevent the bed sliding
when located on smooth or hard surface flooring.
TO REDUCE THE RISK OF SHOCK, BURNS, FIRE OR INJURY:
INNOVA SLEEP PRODUCT
1, 2 & 20 YEAR LIMITED WARRANTY
Innova Sleep Products, Inc. (“Innova”) warrants this adjustable bed
to the consumer who is the original purchaser (the “purchaser”),
subject to the terms and conditions set forth herein. This warranty
begins on the “warranty commencement date” which is the date of
purchase for new unused beds and the date of manufacture for beds
that have been used as floor or display models. Thus, on a floor model
bed, the warranty is a portion of the limited 20 year warranty.
FULL 1 YEAR WARRANTY
This adjustable bed is warranted against defects in the workmanship
or materials for a period of one (1) year from the warranty
commencement date. Upon notice during the first year after the
warranty commencement date, Innova will repair or replace (at no
cost to the purchaser) any defective adjustable bed part, and INNOVA
will pay all authorized labor and transportation costs associated
with the repair of replacement of any parts found to be defective .
When the adjustable bed at hand is found to be DAMAGED, not
DEFECTIVE, all costs incurred to inspect and/or correct the requested
issue will be the financial responsibility of the requesting party.
2 YEAR LIMITED WARRANTY
During the second year from the warranty commencement date,
upon receipt of notice,
20 YEAR LIMITED WARRANTY
Upon notice during the third year through the lifetime from the
warranty commencement date, INNOVA will replace, upon term and
conditions set forth in this paragraph, any mechanical bed part
found to be defective. Electronics, electrical components, drive
motors and massage motors are excluded . This limited warranty
shall not apply unless the defective part is returned to INNOVA
INNOVA will replace any adjustable
bed part found to be defective. Purchaser shall pay all service and
transportation costs related to the replacement of the defective
part . This limited two (2) year warranty shall not apply unless the
defective part is returned to INNOVA and INNOVA receive all
service and transportation cost .
. In years
3 - 20 years , purchaser shall pay all service and transportation costs related
to the replacement of the defective part and required to pay 1/20 of the
current replacement cost of the parts times the number of year used .
for validation
and
INNOVA receive all service and transportation cost for validation
ADDITIONAL TERMS AND CONDITIONS
This warranty does not apply; (a) to any damage caused by the
purchaser; (b) if there has been any repair or replacement of
adjustable bed parts by an unauthorized person; (c) if the
adjustable bed has been mishandled (whether in transit or by
other means), subjected to physical or electrical abuse or misuse, or
otherwise operated in any manner inconsistent with the operation
and maintenance procedures outlined in the Owner’s Manual and

9-11
4-11
Make sure the base is in a flat position. Always unplug the base
from the electrical outlet before cleaning or servicing the base. If the
cord or plug is damaged, discontinue use of the bed base and contact
qualified service personnel for examination and repair.
FCC COMPLIANCE:
This device complies with part 15 of the FCC Rules for residential use.
Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Used to raise and lower
the head of the bed .
Wireless Remote
Adjustable Beds
Head up button
Press to Raise the
head of the bed
Head down button
Press to low the
head of the bed
Foot up button Foot down button
Press to raise the
foot of the bed
Press to low the
foot of the bed
Head&Foot up button
Head&Foot down button
Press one button to
raise both the head
and foot at the same
time
Press one button to low
both the head and foot
at the same time
For toll-free customer service, call 1-877-386-1373
email us: [e-mail]
Please tell us your name, phone, address , serial No.
( ),
and the problem when you call/email.
found on the foot beam of the bed
Indicator light
Radio Frequency: 2.4 GHz

5-11
8-11
USING SAME REMOTE
USING 2 REMOTE ON SAME BED
Master Remote
the
HEAD&FOOT UP and HEAD&FOOT DOWN button of the clone remote,
the desynchronizing process is successful when the clone indicator
light normally on.
The bed base is designed to allow two twin X-Long bases to become
an Eastern King base and two Split-Cal-King bases to become a
Cal-King base. And you can use the same remote to control two side
by side beds bases by following Step 7 on the installation guide to
synchronize the remote with the two control boxes of the two units.
Press the FOOT DOWN and HEAD&FOOT UP button of a new remote
(the one that have not sync with the beds),The indicator’s light will
be on for 17 seconds. Then press HEAD DOWN and FOOT UP buttons
of the , the copying process is successful when the
clone indicator start to flash. Now both remote control will be able to
control both beds to same position.
To desynchronize the clone remote from master remote ,press
Setup is now complete. Enjoy.
SETUP and INSTALLATION
Important: We strongly recommend
Two able-bodied adults setup and
assemble this product.
Step 1:
Check and verify all parts are included before discarding any packing
materials.
All electronics and components that need to be installed are located
in boxes under the base or attached to the frame.
A)Wireless Remote Control (1)
B)Mattress Retainer Bar (1)
C)Legs (4)
D)Power Cord (1)
E)Transformer (1)
F)Control Box (1)
G)Registration Form (1)
Step 2:
With the help of your able-bodied assistant, place carton on floor
with arrows point downwards.
Step 3:
Connect the Transformer “E” to Control Box “F” : The Control Box
is the Black Box attached to the bottom of the bed . Extend the
Power Cord from the Control Box “F” and attach to the short
electrical output cord on Transformer “E” . Extend the Power Cord
“D” and plug it into the Transformer “E” . (See Figure 1)
D

7-11
6-11
Figure 2
Figure 5 Figure 6
Step 8:
-Unplug the Power Cord.
-Install the four legs firmly into the base of the frame. The legs screw
into the threaded holes in each corner of the adjustable base frame
(See Figure 2).
-Do not over tighten
Step 9:
With the help of your able-bodied assistant , carefully lift the
adjustable bed frame and set it in place upright on its legs . Excessive
pressure may damage the legs. Remove all protective plastic covering.
Note: check and make sure that all power cords clear and do not
interfere with any Adjustable Bed Mechanisms; Dispose of covering
property to avoid injury.
Step 10:
Note : The Mattress Retaining Bar is mounted upside down for
shipping only . Remove the Mattress Retaining Bar on the foot of the
bed and turn the bar upright and reinstall by carefully aligning and
pushing the bar into place . Inset the retaining clips to secure the bar
into place . (See Figures 5 & 6. )
Step 4:
Locate the Wireless Remote control and insert 2 AAA batteries
(See Figure 3)
Step 5& 6:
Plug electrical cord into a grounded electrical outlet . Using the
Wireless Remote, push the Head Up button, Foot Up button for a
momentary test of the Wireless Remote. If the motor is working
quickly let go of the button and skip to step 8.
Step 7:
Synchronize the remote control with the control box. First find
the control box mounted under the bed. Press HEAD DOWN and
FOOT UP buttons simultaneously ,the Indicator light on remote
control is flashing, then press the RESET button(See Fig.4) on
the side of the control box, you will hear some quick beeping
sounds. The adjustable bed should be working after matching the
remote control with the control box. Press the HEAD UP button to
test.
RESET
Reset Coding
Figure4
Figure3

7-11
6-11
Figure 2
Figure 5 Figure 6
Step 8:
-Unplug the Power Cord.
-Install the four legs firmly into the base of the frame. The legs screw
into the threaded holes in each corner of the adjustable base frame
(See Figure 2).
-Do not over tighten
Step 9:
With the help of your able-bodied assistant , carefully lift the
adjustable bed frame and set it in place upright on its legs . Excessive
pressure may damage the legs. Remove all protective plastic covering.
Note: check and make sure that all power cords clear and do not
interfere with any Adjustable Bed Mechanisms; Dispose of covering
property to avoid injury.
Step 10:
Note : The Mattress Retaining Bar is mounted upside down for
shipping only . Remove the Mattress Retaining Bar on the foot of the
bed and turn the bar upright and reinstall by carefully aligning and
pushing the bar into place . Inset the retaining clips to secure the bar
into place . (See Figures 5 & 6. )
Step 4:
Locate the Wireless Remote control and insert 2 AAA batteries
(See Figure 3)
Step 5& 6:
Plug electrical cord into a grounded electrical outlet . Using the
Wireless Remote, push the Head Up button, Foot Up button for a
momentary test of the Wireless Remote. If the motor is working
quickly let go of the button and skip to step 8.
Step 7:
Synchronize the remote control with the control box. First find
the control box mounted under the bed. Press HEAD DOWN and
FOOT UP buttons simultaneously ,the Indicator light on remote
control is flashing, then press the RESET button(See Fig.4) on
the side of the control box, you will hear some quick beeping
sounds. The adjustable bed should be working after matching the
remote control with the control box. Press the HEAD UP button to
test.
RESET
Reset Coding
Figure4
Figure3

5-11
8-11
USING SAME REMOTE
USING 2 REMOTE ON SAME BED
Master Remote
the
HEAD&FOOT UP and HEAD&FOOT DOWN button of the clone remote,
the desynchronizing process is successful when the clone indicator
light normally on.
The bed base is designed to allow two twin X-Long bases to become
an Eastern King base and two Split-Cal-King bases to become a
Cal-King base. And you can use the same remote to control two side
by side beds bases by following Step 7 on the installation guide to
synchronize the remote with the two control boxes of the two units.
Press the FOOT DOWN and HEAD&FOOT UP button of a new remote
(the one that have not sync with the beds),The indicator’s light will
be on for 17 seconds. Then press HEAD DOWN and FOOT UP buttons
of the , the copying process is successful when the
clone indicator start to flash. Now both remote control will be able to
control both beds to same position.
To desynchronize the clone remote from master remote ,press
Setup is now complete. Enjoy.
SETUP and INSTALLATION
Important: We strongly recommend
Two able-bodied adults setup and
assemble this product.
Step 1:
Check and verify all parts are included before discarding any packing
materials.
All electronics and components that need to be installed are located
in boxes under the base or attached to the frame.
A)Wireless Remote Control (1)
B)Mattress Retainer Bar (1)
C)Legs (4)
D)Power Cord (1)
E)Transformer (1)
F)Control Box (1)
G)Registration Form (1)
Step 2:
With the help of your able-bodied assistant, place carton on floor
with arrows point downwards.
Step 3:
Connect the Transformer “E” to Control Box “F” : The Control Box
is the Black Box attached to the bottom of the bed . Extend the
Power Cord from the Control Box “F” and attach to the short
electrical output cord on Transformer “E” . Extend the Power Cord
“D” and plug it into the Transformer “E” . (See Figure 1)
D

9-11
4-11
Make sure the base is in a flat position. Always unplug the base
from the electrical outlet before cleaning or servicing the base. If the
cord or plug is damaged, discontinue use of the bed base and contact
qualified service personnel for examination and repair.
FCC COMPLIANCE:
This device complies with part 15 of the FCC Rules for residential use.
Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Used to raise and lower
the head of the bed .
Wireless Remote
Adjustable Beds
Head up button
Press to Raise the
head of the bed
Head down button
Press to low the
head of the bed
Foot up button Foot down button
Press to raise the
foot of the bed
Press to low the
foot of the bed
Head&Foot up button
Head&Foot down button
Press one button to
raise both the head
and foot at the same
time
Press one button to low
both the head and foot
at the same time
For toll-free customer service, call 1-877-386-1373
email us: [e-mail]
Please tell us your name, phone, address , serial No.
( ),
and the problem when you call/email.
found on the foot beam of the bed
Indicator light
Radio Frequency: 2.4 GHz

3-11
10-11
PRODUCT RATINGS:
The bed lift motors are not designed for continuous use of more than
2 minutes in an 18 minutes period, or approximately 10% duty cycle.
Any attempt to circumvent or exceed this rating will shorten the
life expectancy of the product and may void the warranty.
WEIGHT UNITS:
The limitation for this adjustable bed is 750 lbs. The bed will
structurally support these weights, provided it is evenly distributed
across the head and foot sections. This product is not designed to
support or lift this amount in the head or foot section alone.
Exceeding this weight restriction could damage the bed and/or
cause injury and void the warranty. Enter or exit the bed in a flat
position and do not sit on the head or foot sections while in the raised
position.
LIFTING AND LOWERING MECHANISMS :
It is normal for the raising and lowering feature on this bed to emit
a minimal humming sound during operation.
LOCATION ENVIRONMENT:
The level of sound experienced in a room is directly related to the
environment within that location. In a room with hardwood floors
and the massagers turned on, a vibrating noise can be noticeable. To
reduce the resonance, place a piece of carpet or rubber casters cups
under the legs. The rubber caster cups also prevent the bed sliding
when located on smooth or hard surface flooring.
TO REDUCE THE RISK OF SHOCK, BURNS, FIRE OR INJURY:
INNOVA SLEEP PRODUCT
1, 2 & 20 YEAR LIMITED WARRANTY
Innova Sleep Products, Inc. (“Innova”) warrants this adjustable bed
to the consumer who is the original purchaser (the “purchaser”),
subject to the terms and conditions set forth herein. This warranty
begins on the “warranty commencement date” which is the date of
purchase for new unused beds and the date of manufacture for beds
that have been used as floor or display models. Thus, on a floor model
bed, the warranty is a portion of the limited 20 year warranty.
FULL 1 YEAR WARRANTY
This adjustable bed is warranted against defects in the workmanship
or materials for a period of one (1) year from the warranty
commencement date. Upon notice during the first year after the
warranty commencement date, Innova will repair or replace (at no
cost to the purchaser) any defective adjustable bed part, and INNOVA
will pay all authorized labor and transportation costs associated
with the repair of replacement of any parts found to be defective .
When the adjustable bed at hand is found to be DAMAGED, not
DEFECTIVE, all costs incurred to inspect and/or correct the requested
issue will be the financial responsibility of the requesting party.
2 YEAR LIMITED WARRANTY
During the second year from the warranty commencement date,
upon receipt of notice,
20 YEAR LIMITED WARRANTY
Upon notice during the third year through the lifetime from the
warranty commencement date, INNOVA will replace, upon term and
conditions set forth in this paragraph, any mechanical bed part
found to be defective. Electronics, electrical components, drive
motors and massage motors are excluded . This limited warranty
shall not apply unless the defective part is returned to INNOVA
INNOVA will replace any adjustable
bed part found to be defective. Purchaser shall pay all service and
transportation costs related to the replacement of the defective
part . This limited two (2) year warranty shall not apply unless the
defective part is returned to INNOVA and INNOVA receive all
service and transportation cost .
. In years
3 - 20 years , purchaser shall pay all service and transportation costs related
to the replacement of the defective part and required to pay 1/20 of the
current replacement cost of the parts times the number of year used .
for validation
and
INNOVA receive all service and transportation cost for validation
ADDITIONAL TERMS AND CONDITIONS
This warranty does not apply; (a) to any damage caused by the
purchaser; (b) if there has been any repair or replacement of
adjustable bed parts by an unauthorized person; (c) if the
adjustable bed has been mishandled (whether in transit or by
other means), subjected to physical or electrical abuse or misuse, or
otherwise operated in any manner inconsistent with the operation
and maintenance procedures outlined in the Owner’s Manual and

11-11
WARNING
Attention: Read the following information
before using this product . Failure to use a
surge protection device could compromise
safety or cause product malfunction and could
void the electrical portion of your warranty.
- Electrical surges are by far the biggest cause of problems with
electrical circuits.
In order to help protect your investment in case of a power surge or
outage, use an electrical surge protection device (not included).
WARRANTY WARNING!
Do not open or tamper with the transformer, control box, motors, or
remote control (with the exception of battery compartments). The
product warranty will be void if these components are tampered
with.
SMALL CHILDREN AND PETS:
Immediately dispose of all packing materials as they can smother
small children and pets. Do not allow any persons or pets under the
bed. Children, convalescents and disabled person should not operate
the bed without adult supervision.
HOSPITAL OR CONVALESCENT USE DISCLAIMER:
Adjustable beds are designed and engineered for a life style of
in-home comfort and are not intended for hospital use or for a
bed-ridden patient on an extended recovery. Adjustable beds are not
equipped with bars to help patients get safely in and out of bed and
are not intended to be used around tent type oxygen therapy or
explosive gases.
2-11
this warranty; (d) to damage to mattresses, fabric, cables,
electrical cords or items supplied by dealers. Contact the
dealer for warranty information on these items; (e) if there
has been any modification of the adjustable bed without prior
written consent by Innova; (f) to costs for unnecessary service
calls, including costs for in-home service calls solely for the
purpose of education the consumer about the adjustable bed
or finding an unsatisfactory power connection; (g) if the
recommended weight restriction is not followed (refer to the
advisory section of this manual), the warranty will be void.
Repairs to or replacement of an adjustable bed or its
components under the terms of this limited warranty will
apply to the original warranty period and will not serve to
extend such period. The decision to repair or to replace defective
parts under this warranty shall be made, or cause to be made, by
INNOVA at its option and in its sole discretion. Repair or
replacement shall be the sole remedy of the purchaser. There
shall be no liability on the part of Innova for any special, indirect,
incidental, or consequential damages or for any other damage,
claim, or loss not expressly covered by the terms of this
warranty. This limited warranty does not include
reimbursement for inconvenience, removal, installation, setup
time, loss of use, shipping, or any other costs of expenses,
Innova and/or its service technicians shall not be responsible for
moving furniture or any other items not attached to the
adjustable bed in order to perform service on the adjustable
bed. It is the sole responsibility of the purchaser to provide
adequate space and accessibility to the adjustable bed. In the
event that the technician is unable to perform service due to lack
of accessibility, the service call will be billed to the purchaser
and the service will have to be rescheduled. Innova makes no
other warranty whether expressed or implied, and all implied
warranties of merchantability and fitness for a particular
purpose are disclaimed by Innova and excluded from this
agreement. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation
or exclusion may not apply to every purchaser. This warranty
gives the purchaser specific legal rights, and the purchaser may
also have other rights, which may vary from state to state. This
warranty is valid in all 50 states, Puerto Rico, and Canada.