Inovance SV660F Series User manual

‑1‑
Preface
Preface
Introduction
The SV660F series high performance AC servo drive provides a power range from 0.05
kW to 7.5 kW. It supports Profinet communication protocol and carries Ethernet
communication interfaces to work with the host controller for a networked operation
of multiple servo drives.
The SV660N series servo drive supports stiffness level setting, inertia auto‑tuning and
vibration suppression to simplify the operation process. It allows a quiet and stable
operation through cooperating with the MS1 series medium‑to‑small inertia high‑
response servo motors configured with a 23‑bit multi‑turn absolute encoder.
It is suitable for lithium battery PACK, printing and packaging, logistics, automobile
manufacturing, tobacco and other industries to achieve fast and accurate
collaborative control.
This guide presents installation of the servo drive, including installation steps,
mechanical installation, and electrical installation.
More Documents
Name Data Code Description
SV660F Series Servo Drive
Selection Guide 19011667
Provides instructions on product
selection, including the list of
supporting components, technical data
on the drive and motor, and the
selection guide of cables.
SV660F Series Servo Drive
Hardware Guide 19011666
Presents electrical design guidance of
the equipment, description of terminals,
required certificates and standards and
solutions to common EMC problems.
SV660F Series Servo Drive
Commissioning Guide 19011668
Presents servo commissioning,
parameter descriptions, including the
operating panel, commissioning
software, commissioning procedure and
a parameter list.
SV660F Series Servo Drive
Communication Guide 19011670
Presents functions and parameters of
the servo drive, including Profinet
communication configuration,
parameter description, and
communication application cases.
SV660P Series Servo Drive
Function Guide 19011669
Presents functions and parameters,
including function overview, basic servo
functions, adjustment and parameter
list.

‑2‑
Preface
Name Data Code Description
SV660F Series Servo Drive
installation Guide 19012103
Presents installation of the servo drive,
including installation steps, ,
mechanical installation, and electrical
installation.
SV660F Series Servo Drive
Troubleshooting Guide 19012104
Introduces faults and fault levels, the
troubleshooting process, warning codes
and fault codes.
SV660F Series Servo Drive
Maintenance Guide 19012105 Provides instructions on maintenance
and repair of the equipment.
SV660F Series Servo Drive Safety
Guide 19012110
Presents the safety function and related
certifications and standards, wiring,
commissioning process,
troubleshooting, and functions.
SV660F Series Servo Drive
Manual Package PS00005951
Provides information on selection,
installation, commissioning, function,
troubleshooting and parameters of the
equipment.
Revision History
Date of
Revision Version Description
2022‑07 A00 First release.
Document Acquisition
This manual is not delivered with the product. You can obtain the PDF version by
visiting:
●
http://www.inovance.com
.
●Scan the QR code on the equipment to acquire more.
Warranty
Inovance provides warranty service within the warranty period (as specified in your
order) for any fault or damage that is not caused by improper operation of the user.
You will be charged for any repair work after the warranty period expires.
Within the warranty period, you will be charged if the product is damaged due to the
following causes.
●Failure to operate this product as specified in this guide.
●Fire, flood, or abnormal voltage.
●Unintended use of the product.
●Operation beyond the product's ratings.
●Force majeure (natural disaster, earthquake, and lightning strike).

‑3‑
Preface
The maintenance fee is charged according to the latest Price List of Inovance. If
otherwise agreed upon, the terms and conditions in the agreement shall prevail.

‑4‑
TTaabbllee ooff CCoonntteennttss
Preface.............................................................................. 1
General Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2安装流程图........................................................................ 13
3 Preparation Before Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.1 Installation Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2 Installation Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.3 Installation Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.4 Optional Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.5 Cable Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4 Unpacking Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.1 Unpacking Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5 Mechanical Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.1 Safety Cautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.2 Pre‑Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.3 Installing the Absolute Encoder Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.4 Mounting the Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.5 Installing the Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.6 Post‑Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6 Electrical Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.1 Safety Cautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.2 Wiring of the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.3 Wiring with the Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6.4 Wiring with the Encoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
6.5 Post‑Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table of Contents

‑5‑
General Safety Instructions
General Safety Instructions
Safety Precautions
●This section explains the safety precautions that need to be observed to use this
product correctly. Before using this product, please read the instruction manual
and correctly understand the relevant information of safety precautions. Failure to
comply with the safety precautions may result in death, serious injury, or
equipment damage.
●"CAUTION", "WARNING", and "DANGER" items in the guide only indicate some of
the precautions that need to be followed; they just supplement the safety
precautions.
●Use this equipment according to the designated environment requirements.
Damage caused by improper use is not covered by warranty.
●Inovance shall take no responsibility for any personal injuries or property damage
caused by improper use.
Safety Levels and Definitions
Indicates that failure to comply with the notice will result in death
or severe personal injuries.
Indicates that failure to comply with the notice may result in death
or severe personal injuries.
Indicates that failure to comply with the notice may result in minor
or moderate personal injuries or equipment damage.
General Safety Instructions
●Drawings in the selection guide are sometimes shown without covers or protective
guards. Remember to install the covers or protective guards as specified first, and
then perform operations in accordance with the instructions. Install the covers or
protective guards as specified, and use the equipment in accordance with the
instructions described in the user guide.
●The drawings in the guide are shown for illustration only and may be different
from the product you purchased.

‑6‑
General Safety Instructions
Unpacking
●Do not install the equipment if you find damage, rust, or signs of use on the equipment
or accessories upon unpacking.
●Do not install the equipment if you find water seepage or missing or damaged
components upon unpacking.
●Do not install the equipment if you find the packing list does not conform to the
equipment you received.
●Check whether the packing is intact and whether there is damage, water seepage,
dampness, and deformation before unpacking.
●Unpack the package by following the unpacking sequence. Do not strike the package
violently.
●Check whether there is damage, rust, or injuries on the surface of the equipment and
equipment accessories before unpacking.
●Check whether the package contents are consistent with the packing list before
unpacking.
Storage and Transportation
●Large‑scale or heavy equipment must be transported by qualified professionals using
specialized hoisting equipment. Failure to comply may result in personal injuries or
equipment damage.
●Before hoisting the equipment, ensure the equipment components such as the front
cover and terminal blocks are secured firmly with screws. Loosely‑connected
components may fall off and result in personal injuries or equipment damage.
●Never stand or stay below the equipment when the equipment is being hoisted by the
hoisting equipment.
●When hoisting the equipment with a steel rope, ensure the equipment is hoisted at a
constant speed without suffering from vibration or shock. Do not turn the equipment
over or let the equipment stay hanging in the air. Failure to comply may result in
personal injuries or equipment damage.

‑7‑
General Safety Instructions
●Handle the equipment with care during transportation and mind your steps to prevent
personal injuries or equipment damage.
●When carrying the equipment with bare hands, hold the equipment casing firmly with
care to prevent parts from falling. Failure to comply may result in personal injuries.
●Store and transport the equipment based on the storage and transportation
requirements. Failure to comply will result in equipment damage.
●Avoid storing or transporting the equipment in environments with water splash, rain,
direct sunlight, strong electric field, strong magnetic field, and strong vibration.
●Avoid storing the equipment for more than three months. Long‑term storage requires
stricter protection and necessary inspections.
●Pack the equipment strictly before transportation. Use a sealed box for long‑distance
transportation.
●Never transport the equipment with other equipment or materials that may harm or
have negative impacts on this equipment.
Installation
●The equipment can be operated by well‑trained and qualified professionals only. Non‑
professionals are not allowed.
●Read through the guide and safety instructions before installation.
●Do not install this equipment in places with strong electric or magnetic fields.
●Before installation, check that the mechanical strength of the installation site can bear
the weight of the equipment. Failure to comply will result in mechanical hazards.
●Do not wear loose clothes or accessories during installation. Failure to comply may
result in an electric shock.
●When installing the equipment in a closed environment (such as a cabinet or casing),
use a cooling device (such as a fan or air conditioner) to cool the environment down to
the required temperature. Failure to comply may result in equipment over‑temperature
or a fire.
●Do not retrofit the equipment.
●Do not fiddle with the bolts used to fix equipment components or the bolts marked in
red.
●When the equipment is installed in a cabinet or final assembly, a fireproof enclosure
providing both electrical and mechanical protections must be provided. The IP rating
must meet IEC standards and local laws and regulations.
●Before installing devices with strong electromagnetic interference, such as a
transformer, install a shielding device for the equipment to prevent malfunction.
●Install the equipment onto an incombustible object such as a metal. Keep the
equipment away from combustible objects. Failure to comply will result in a fire.

‑8‑
General Safety Instructions
●Cover the top of the equipment with a piece of cloth or paper during installation. This is
to prevent unwanted objects such as metal chippings, oil, and water from falling into the
equipment and causing faults. After installation, remove the cloth or paper on the top of
the equipment to prevent over‑temperature caused by poor ventilation due to blocked
ventilation holes.
●Resonance may occur when the equipment operating at a constant speed executes
variable speed operations. In this case, install the vibration‑proof rubber under the
motor frame or use the vibration suppression function to reduce resonance.
Wiring
●Equipment installation, wiring, maintenance, inspection, or parts replacement must be
performed only by professionals.
●Before wiring, cut off power connections with all equipment. Residual voltage exists
after power cut‑off. Therefore, wait at least the time designated on the equipment
warning label before further operations. Measure the DC voltage of the main circuit and
make sure it is below the safe voltage, otherwise there will be the danger of electric
shock.
●Do not perform wiring, remove the equipment cover, or touch the circuit board with
power ON. Failure to comply will result in an electric shock.
●Check that the equipment is grounded properly. Failure to comply will result in an
electric shock.
●Do not connect the input power supply to the output end of the equipment. Failure to
comply will result in equipment damage or even a fire.
●When connecting a drive to the motor, check that the phase sequences of the drive and
motor terminals are consistent to prevent reverse motor rotation.
●Cables used for wiring must meet cross sectional area and shielding requirements. The
shield of the cable must be reliably grounded at one end.
●Fix the terminal screws with the tightening torque specified in the user guide. Improper
tightening torque may overheat or damage the connecting part, resulting in a fire.
●After wiring is done, check that all cables are connected properly and no screws,
washers or exposed cables are left inside the equipment. Failure to comply may result in
an electric shock or equipment damage.
●During wiring, follow the proper electrostatic discharge (ESD) procedure, and wear an
antistatic wrist strap. Failure to comply will damage the equipment or the internal
circuits of the equipment.
●Use shielded twisted pairs for the control circuit. Connect the shield to the grounding
terminal of the equipment for grounding purpose. Failure to comply will result in
equipment malfunction.
Power-on

‑9‑
General Safety Instructions
●Before power‑on, check that the equipment is installed properly with reliable wiring and
the motor can be restarted.
●Check that the power supply meets equipment requirements before power‑on to
prevent equipment damage or a fire.
●After power‑on, do not open the cabinet door or protective cover of the equipment,
touch any terminal, or disassemble any unit or component of the equipment. Failure to
comply will result in an electric shock.
●Perform a trial run after wiring and parameter setting to ensure the equipment operates
safely. Failure to comply may result in personal injuries or equipment damage.
●Before power‑on, make sure that the rated voltage of the equipment is consistent with
that of the power supply. Failure to comply may resulting in a fire. Failure to comply
may result in a fire.
●Before power‑on, check that no one is near the equipment, motor, or machine. Failure
to comply may result in death or personal injuries.
Operation
●The equipment must be operated only by professionals. Failure to comply will result in
death or personal injuries.
●Do not touch any connecting terminals or disassemble any unit or component of the
equipment during operation. Failure to comply will result in an electric shock.
●Do not touch the equipment casing, fan, or resistor with bare hands to feel the
temperature. Failure to comply may result in personal injuries.
●Prevent metal or other objects from falling into the equipment during operation. Failure
to comply may result in a fire or equipment damage.
Maintenance
●Equipment installation, wiring, maintenance, inspection, or parts replacement must be
performed only by professionals.
●Do not maintain the equipment with power ON. Failure to comply will result in an
electric shock.
●Before maintenance, cut off all the power supplies of the equipment and wait for at least
the time designated on the equipment warning label.
●In case of a permanent magnet motor, do not touch the motor terminals immediately
after power‑off because the motor terminals will generate induced voltage during
rotation even after the equipment power supply is off. Failure to comply will result in an
electric shock.