Intel P8700 - Core 2 Duo Processor User manual
1
/
16
-
1
/
8
-
1
/
4
DIN LIMIT CONTROLLERS
CONCISE PRODUCT MANUAL (59333-2)
CAUTION: Installation should be only performed by
technically competent personnel. Local Regulations
regarding electrical installation & safety must be observed.
1. INSTALLATION
The models covered by this manual have three different DIN case sizes (refer to
section 9). Some installation details vary between models. These differences have
been clearly shown.
Note: The functions described in sections 2 thru 8 are common to all models.
Installing Option Modules
1
/
16
Din Size Instruments
CPU PCB
Option Module 1
(Fixed Limit Relay)
Option Module 2
Mounting Struts
Option Module A
Option Module 3
PSU PCB
1
/
8
&
1
/
4
Din Size Instruments
CPU PCB
Option Module B
(
not used on Limit
Controllers)
Option Module 2
Option Module 1
(Fixed Limit Relay)
Mounting Struts
Option Module A
Option Module 3
PSU PCB
To access module A, first detach the PSU and CPU boards from the front by lifting
first the upper, and then lower mounting struts. Gently separate the boards.
a. Plug the required option modules into the correct connectors, as shown below.
b. Locate the module tongues in the corresponding slot on the opposite board.
c. Hold the main boards together while relocating back on the mounting struts.
d. Replace the instrument by aligning the CPU and PSU boards with their guides
in the housing, then slowly push the instrument back into position.
Note: Option modules are automatically detected at power up.
Option Module Connectors
1
/
16
Din Size Instruments
Option Slot 1
(Fixed Limit
Relay)
Option Slot
2
Connector
PL4A
Option Slot
A
Connectors
PL5 & PL6
Option Slot 3
Connector
PL4B
1
/
8
&
1
/
4
Din Size Instruments
Option Slot B
(not used on
Limit Cont
rollers)
Option Slot
2
Connector
PL4A
Option Slot 1
(Fixed Limit
Relay)
Option Slot
A
Connectors
PL5 & PL6
Option Slot 3
Connector
PL4B
Panel-Mounting
The mounting panel must be rigid, and may be up to
6.0mm (0.25inch) thick. Cut-out sizes are:
Cut-Out Dim A Cut-Out Dim B
1
/
16
&
1
/
8
Din = 45mm
1
/
16
Din = 45mm
1
/
4
Din = 92mm
1
/
8
&
1
/
4
Din = 92mm
For nmultiple instruments mounted side-by-side, cut-out
A is 48n-4mm (
1
/
16
&
1
/
8
Din) or 96n-4mm (
1
/
4
Din)
Tolerance +0.5, -0.0mm
Mounting Panel
Instrument
Housing
Ratchets
Gasket
Slide mounting clamp
over the instrument
housing towards rear face
of mounting panel until
the tongues engage in
ratchets
and instrument is
clamped in position.
Hold instrument firmly in
position (apply pressure
to bezel only)
CAUTION: Do not remove the panel gasket; it is a seal against dust and
moisture.
Rear Terminal Wiring
USE COPPER CONDUCTORS (EXCEPT FOR T/C INPUT)
Single Strand wire gauge: Max 1.2mm (18SWG)
1
/
16
Din Size Instruments
1
/
8
&
1
/
4
Din Size Instruments
These diagrams show all possible option combinations. The actual
connections required depends on the exact model and options fitted.
CAUTION: Check information label on housing for correct operating
voltage before connecting supply to Power Input
Fuse: 100 – 240V ac – 1amp anti-surge
24/48V ac/dc – 315mA anti-surge
Note: At first power-up the message
is displayed, as described in
section 6 of this manual. Access to other menus is denied until configuration
mode is completed
2. SELECT MODE
Select mode is used to access the configuration and operation menu functions.
It can be accessed at any time by holding down and pressing .
In select mode, press or to choose the required mode, press to enter.
An unlock code is required to prevent unauthorised entry to Configuration, & Setup
modes. Press or to enter the unlock code, then press to proceed.
Mode Upper
Display Lower
Display Description Default
Unlock
Codes
Operator
Normal operation None
Set Up
Tailor settings to the application
Configuration
Configure the instrument for use
Product Info
Check manufacturing information None
Note: The instrument will always return automatically to Operator mode if
there is no key activity for 2 minutes.
3. CONFIGURATION MODE
First select Configuration mode from Select mode (refer to section 2).
Press to scroll through the parameters, then press or to set the required
value. Press to accept the change, otherwise parameter will revert to previous
value. To exit from Configuration mode, hold down and press , to return to
Select mode.
Note: Parameters displayed depends on how instrument has been configured.
Refer to user guide (available from your supplier) for further details.
Parameters marked * are repeated in Setup Mode.
Parameter Lower
Display
Upper
Display
Adjustment range & Description
Default
Value
Input
Range/Type
See following table for possible codes
Code Input Type &
Range Code Input Type &
Range Code Input Type &
Range
bC
bCbC
bC
B: 100 - 1824 ºC
L
LL
L
.
C
CC
C
L: 0.0 - 537.7 ºC
bF
bFbF
bF
B: 211 - 3315 ºF
L
LL
L
.
F
FF
F
L: 32.0 - 999.9 ºF
P24F
P24FP24F
P24F
PtRh20% vs 40%:
32 - 3362 ºF
CC
CCCC
CC
C: 0 - 2320 ºC
NC
NCNC
NC
N: 0 - 1399 ºC
PTC
PTCPTC
PTC
Pt100: –199 - 800 ºC
CF
CFCF
CF
C: 32 - 4208 ºF
NF
NFNF
NF
N: 32 - 2551 ºF
PtF
PtFPtF
PtF
Pt100: –328 - 1472 ºF
JC
JCJC
JC
J: –200 - 1200 ºC
rC
rCrC
rC
R: 0 - 1759 ºC
P
PP
Pt
tt
t
.
C
CC
C
Pt100: –128.8 -
537.7 ºC
JF
JFJF
JF
J: –328 - 2192 ºF
rF
rFrF
rF
R: 32 - 3198 ºF
Pt
PtPt
Pt
.
F
FF
F
Pt100: –199.9 - 999.9 ºF
j
jj
j
.
C
CC
C
J: –128.8 - 537.7 ºC
SC
SCSC
SC
S: 0 - 1762 ºC
0 - 20 mA DC
j
jj
j
.
F
FF
F
J: –199.9 - 999.9 ºF
SF
SFSF
SF
S: 32 - 3204 ºF
4 - 20 mA DC
KC
KCKC
KC
K: –240 - 1373 ºC
tC
tCtC
tC
T: –240 - 400 ºC
0 - 50 mV DC
KF
KFKF
KF
K: –400 - 2503 ºF
tF
tFtF
tF
T: –400 - 752 ºF
.
10 - 50 mV DC
k
kk
k
.
C
CC
C
K: –128.8 - 537.7 ºC
t
tt
t
.
C
CC
C
T: –128.8 - 400.0 ºC
0 - 5 V DC
K
KK
K
.
F
FF
F
K: –199.9 - 999.9 ºF
t
tt
t
.
F
FF
F
T: –199.9 - 752.0 ºF
1 - 5 V DC
LC
LCLC
LC
L: 0 - 762 ºC
0 - 10 V DC
LF
LFLF
LF
L: 32 - 1403 ºF
P24C
P24CP24C
P24C
PtRh20% vs. 40%:
0 - 1850 ºC
2 - 10 V DC
Note: Decimal point shown in table indicates temperature resolution of 0.1°
Parameter Lower
Display
Upper
Display
Adjustment range & Description
Default
Value
Scale Range
Upper Limit
Scale Range Lower Limit +100
to Range Maximum
Range max
(Lin=1000)
Scale Range
Lower Limit
Range Minimum to
Scale Range Upper Limit -100
Range min
(Linear=0)
Decimal point
position
=XXXX,
=XXX.X,
=XX.XX,
=X.XXX
(non-temperature ranges only)
Process Variable
Offset
±Span of controller
(see CAUTION note at end of section)
High Limit.
Limit relay is energised when
process “safe” (PV < Limit Setpoint)
Limit Action
Low Limit.
Limit relay is energised when
process “safe” (PV > Limit Setpoint)
Setpoint Upper
Limit
Current Setpoint to Scale Range maximum
R/max
Setpoint Lower
Limit
Scale Range minimum to Current Setpoint
R/min
Process High Alarm
Process Low Alarm
Deviation Alarm
Band Alarm
Alarm 1Type
No alarm
High Alarm 1
value*
Range Max
Low Alarm 1
value*
Scaled Range Minimum to
scaled Range Maximum in display units Range Min
Band Alarm 1
value*
1 LSD to span from setpoint in display units
Dev. Alarm 1
value*
+/- Span from setpoint in display units
Alarm 1
Hysteresis* !
!!
!
1 LSD to full span in display units
Parameter Lower
Display
Upper
Display
Adjustment range & Description
Default
Value
Alarm 2 Type*
High Alarm 2
value*
Range Max
Low Alarm 2
value*
Range Min
Band Alarm 2
value*
Dev. Alarm 2
Value*
Alarm 2
Hysteresis* !
!!
!
Options as for alarm 1
Mm
MmMm
Mm
Limit Output Relay
"
""
"
Alarm 1, Direct
Alarm 1, Reverse
Alarm 2, Direct
Alarm 2, Reverse
Logical Alarm 1 OR 2, Direct
Logical Alarm 1 OR 2, Reverse
Logical Alarm 1 AND 2, Direct
Logical Alarm 1 AND 2, Reverse
Limit Annunciator, Direct
Limit Annunciator, Reverse
"
""
"
Retransmit Limit SP Output
Output 2 Usage #
##
#
Retransmit PV Output
0 to 5 V DC output 1
0 to 10 V DC output
2 to 10 V DC output
0 to 20 mA DC output
Linear Output 2
Range !
!!
!
4 to 20 mA DC output
Retransmit
Output 2 Scale
maximum
-1999 to 9999
(display value at which output
will be maximum) Range max
Retransmit
Output 3 Scale
minimum
-1999 to 9999
(display value at which output
will be minimum) Range min
Output 3 Usage #
##
#
As for output 2 "
""
"
Linear Output 3
Range !
!!
!
As for output 2
Retransmit
Output 3 Scale
maximum
-1999 to 9999
(display value at which output
will be maximum) Range max
Retransmit
Output 3 Scale
minimum
-1999 to 9999
(display value at which output
will be minimum) Range min
PV is visible in Operator mode
PV not visible in Operator mode
Display Strategy
$
$$
$
Displays
in Operator mode
when Limit Output is not active
%
%%
%
ASCII
Mm
MmMm
Mm
Modbus with no parity
Mm
MmMm
Mm
Modbus with Even Parity
Serial
Communications
Protocol
Mm
MmMm
Mm
Modbus with Odd Parity
Mm
MmMm
Mm
.
1.2 kbps
.
2.4 kbps
.&
&&
&
4.8 kbps
'
''
'.(
((
(
9.6 kbps
Serial
Communications
Bit Rate
'
''
'.
19.2 kbps
.&
&&
&
Comms Address
1 to 255 (Modbus), 1 to 99 (ASCII)
Ww
WwWw
Ww
Read/Write
Comms Write
Read only
Ww
WwWw
Ww
Configuration
Lock Code )
))
)
0 to 9999
Notes: Output 1 is always a Latching Limit Relay output.
If Option Slot A has the Digital Input module fitted, this always functions as a
Remote Reset, duplicating the function of the Reset) key .
As these functions cannot be changed, no Configuration menus are required.
CAUTION: Process Variable Offset can be used to modify the
measured value to compensate for probe errors. Positive values
increase the reading, negative values are subtracted. This parameter
is effectively, a calibration adjustment and MUST be used with care.
There is no front panel indication of when this parameter is in use.
A
B
4. SETUP MODE
Note: Configuration must be completed before adjusting Setup parameters.
First select Setup mode from Select mode (refer to section 2). The Setup LED
will light while in Setup mode. Press to scroll through the parameters,
then press or to set the required value.
To exit from Setup mode, hold down and press to return to Select mode.
Note: Parameters displayed depends on how instrument has been configured.
Parameter Lower
Display Upper Display Adjustment
Range & Description Default
Value
Limit Setpoint value
Scaled Range Minimum to
scaled Range Maximum
R/max if
=
R/min if
=
Limit Hysteresis *
**
*
1 LSD to full span in display units,
on the safe side of the limit SP
Input Filter Time Constant
OFF or 0.5 to 100.0 secs
(see CAUTION note below)
.
High Alarm 1 value
R/max
Low Alarm 1 value
Scaled Range Minimum to
scaled Range Maximum R/min
Deviation Alarm 1 Value
±Span from SP in display units
Band Alarm 1 value
1 LSD to span from setpoint
Alarm 1 Hysteresis !
!!
!
1 LSD to full span in display units
High Alarm 2 value
R/max
Low Alarm 2 value
Scaled Range Minimum to
scaled Range Maximum R/min
Deviation Alarm 2 Value
±Span from SP in display units
Band Alarm 2 value
1 LSD to span from setpoint
Alarm 2 Hysteresis !
!!
!
1 LSD to full span in display units
Setup Lock Code )
))
)
0 to 9999
Note: Operator mode screens follow, without exiting from Setup mode.
CAUTION: An excessively large filter time could significantly delay
detection of a limit condition. Set this value to the minimum required
to remove noise from the process variable
5. PRODUCT INFORMATION MODE
First select Product information mode from Select mode (refer to section 2).
Press to view each parameter. To exit from Product Information mode,
hold down and press to return to Select mode.
Note: These parameters are all read only.
Parameter Lower
Display
Upper
Display
Description
Input type %
%%
%
#
##
#
Universal input
Option 1 type (fixed)
*
**
*
Latching Limit Relay
No option fitted
*
**
*
Relay output
SSR drive output
Triac output
Option 2 module type
fitted
Linear DC voltage / current output
No option fitted
*
**
*
Relay output
SSR drive output
Linear DC voltage / current output
Option 3 module type
fitted
)
))
)
Transmitter power supply
No option fitted
&
&&
&
RS485 communications
Auxiliary Option A
module type fitted
Digital Input for remote reset
Firmware type +,
+,+,
+,
Value displayed is firmware type number
Firmware issue %$$
%$$%$$
%$$
Value displayed is firmware issue number
Product Revision Level
Value displayed is Product Revision level
Date of manufacture
Mm
MmMm
Mm
Manufacturing date code (mmyy)
Serial number 1
First four digits of serial number
Serial number 2
Middle four digits of serial number
Serial number 3
Last four digits of serial number
6. ERROR/FAULT INDICATIONS
Parameter Upper
Display
Lower
Display
Description
Instrument
parameters are in
default conditions
Configuration & Setup required. This screen is
seen at first turn on, or if hardware
configuration has been changed. Press to
enter the Configuration Mode, next press
or to enter the unlock code number,
then press to proceed
-
--
-
.
..
.
Normal
Process variable input > 5% over-range
Input Over Range
Normal
-
--
-
.
..
.
as above if Display Strategy =
-
--
-
.
..
.
Normal
Process variable input > 5% under-range
Input Under
Range Normal
-
--
-
.
..
.
as above if Display Strategy =
/
//
/
Normal
Break detected in process variable input
sensor or wiring
Input Sensor
Break Normal
/
//
/
as above if Display Strategy =
Option 1 Error
Option 1 module fault
Option 2 Error
Option 2 module fault
Option 3 Error
Option 3 module fault
Option A Error
Option A module fault
Option B Error
Option B not used on Limit Controllers
this error is shown if any module is fitted
7. OPERATOR MODE
This mode is entered at power on, or accessed from Select mode (see section 2).
Note: All Configuration mode and Setup mode parameters must be set as
required before starting normal operations.
Press to scroll through the parameters.
Upper
Display Lower
Display
Display Strategy and
When Visible Description
PV Value
Limit SP
Value
=
(initial screen) PV and Limit Setpoint values
Read only
Limit SP
Value (Blank)
=
(initial screen) Limit Setpoint value
Read only
or
(Blank)
or PV
Value
=
.
(Initial Screen)
Displays
and PV if Limit
Output is active or
and blank
if not active.
Read only
High Limit
Hold
=
Highest PV value since this
parameter was last reset.
To reset, press for 5 seconds,
display =
0000
when reset
Low Limit
Hold
=
Lowest PV value since this
parameter was last reset.
To reset, press for 5 seconds,
display =
0000
when reset
Exceed Time
Value
Always available
Format
mm.ss to 99.59
then mmm.s
(10 sec increments)
Shows
-
--
-
.
..
.
if 999.9
Accumulated time of Limit SP
exceed conditions since this
parameter was last reset.
To reset, press for 5 seconds,
display =
0000
when reset
Active Alarm
Status
When one or more
alarms are active.
ALM indicator
will also flash
L
Alarm 2 active
Alarm 1 active
L
Annunciator active
Exceed Condition
An Exceed Condition is when the Process Variable exceeds the Limit Setpoint value
(i.e. PV > SP when set for high limit action, PV < SP for low limit action). The
LED is on during this condition, and is extinguished once it has passed.
Limit Output Function
Limit Output relay(s) de-energise whenever an Exceed condition occurs, causing
the process to shut down. The LED is on when the relay is de-energised.
The relay remains latched off even if the Exceed condition is no longer present.
Only giving a reset instruction (after the exceed condition has passed) will re-
energise the relay, allowing the process to continue. The LED then turns off.
Limit Annunciator Outputs
An Annunciator output will activate when an Exceed condition occurs, and will
remain active until a reset instruction is received, or the Exceed condition has
passed. Unlike the Limit Output, an Annunciator can be reset even if the Exceed
condition is present. When an Annunciator is active, the LED will flash and the
Alarm Status screen is available.
Resetting Limit Outputs & Annunciators
A reset instruction can be given by pressing the key, via the Digital Input (if
fitted) or via a Comms command if an RS485 Communications module is fitted.
Annunciators will deactivate. Limit Outputs will only re-energise if the Exceed
condition has passed.
CAUTION: Ensure that the cause of the Exceed condition has been
rectified before resetting the Limit Output.
8. SERIAL COMMUNICATIONS
Refer to the full user guide (available from your supplier) for details.
9. SPECIFICATIONS
UNIVERSAL INPUT
Thermocouple
Calibration: ±0.1% of full range, ±1LSD (±1°C for Thermocouple CJC).
BS4937, NBS125 & IEC584.
PT100 Calibration: ±0.1% of full range, ±1LSD.
BS1904 & DIN43760 (0.00385
Ω
/
Ω
/°C).
DC Calibration: ±0.1% of full range, ±1LSD.
Sampling Rate: 4 per second.
Impedance: >10MΩresistive, except DC mA (5Ω) and V (47kΩ).
Sensor Break
Detection: Thermocouple, RTD, 4 to 20 mA, 2 to 10V and 1 to 5V ranges
only. Limit outputs turn off (goes into Exceed condition), high
alarms activate for thermocouple/RTD sensor break, low
alarms activate for mA/V DC sensor break.
Isolation: Isolated from all outputs (except SSR driver).
Universal input must not be connected to operator accessible
circuits if relay outputs are connected to a hazardous voltage
source. Supplementary insulation or input grounding would
then be required.
DIGITAL INPUT
Volt-free(or TTL): Open(2 to 24VDC) =No Reset.
Closed(<0.8VDC) = Reset (edge triggered).
Isolation: Reinforced safety isolation from inputs and other outputs.
OUTPUTS
Limit Relay
Contact Type &
Rating: Latching limit control relay. Single pole double throw (SPDT);
5A resistive at 120/240VAC. Slot 1 position fixed for this
function, optional function for Slot 2 & 3 relay modules,
Lifetime: >100,000 operations at rated voltage/current.
Isolation: Basic Isolation from universal input and SSR outputs.
Alarm Relays
Contact Type &
Rating: Slot 2 or 3 position non-latching alarm relay.
Single pole double throw (SPDT); 2A resistive at 120/240VAC.
Lifetime: >500,000 operations at rated voltage/current.
Isolation: Basic Isolation from universal input and SSR outputs.
SSR Driver
Drive Capability: SSR drive voltage >10V into 500Ωmin.
Isolation: Not isolated from universal input or other SSR driver outputs.
Triac
Operating Voltage: 20 to 280Vrms (47 to 63Hz).
Current Rating: 0.01 to 1A (full cycle rms on-state @ 25°C);
derates linearly above 40°C to 0.5A @ 80°C.
Isolation: Reinforced safety isolation from inputs and other outputs.
DC
Resolution: 8 bits in 250mS (10 bits in 1s typical, >10 bits in >1s typical).
Isolation: Reinforced safety isolation from inputs and other outputs.
Transmitter PSU
Power Rating: 20 to 28V DC (24V nominal) into 910Ωminimum resistance.
Isolation: Reinforced safety isolation from inputs and other outputs.
SERIAL COMMUNICATIONS
Physical: RS485, at 1200, 2400, 4800, 9600 or 19200 bps.
Protocols: Selectable between Modbus and West ASCII.
Isolation: Reinforced safety isolation from all inputs and outputs.
OPERATING CONDITIONS (FOR INDOOR USE)
Ambient
Temperature: 0°C to 55°C (Operating), –20°C to 80°C (Storage).
Relative Humidity: 20% to 95% non-condensing.
Supply Voltage and
Power: 100 to 240VAC ±10%, 50/60Hz, 7.5VA
(for mains powered versions), or
20 to 48VAC 50/60Hz 7.5VA or 22 to 65VDC 5W
(for low voltage versions).
ENVIRONMENTAL
Standards: CE, UL, ULC & FM 3545, 1998
EMI: Complies with EN61326 (Susceptibility & Emissions).
Safety
Considerations: Complies with EN61010-1 & UL3121.
Pollution Degree 2, Installation Category II.
Front Panel Sealing:
To IP66 (IP20 behind the panel).
PHYSICAL
Front Bezel Size:
1
/
16
Din = 48 x 48mm,
1
/
8
Din = 96 x 48mm,
1
/
4
Din = 96 x 96mm.
Depth Behind Panel:
1
/
16
Din = 110mm, ,
1
/
8
&
1
/
4
Din = 100mm.
Weight: 0.21kg maximum.
Other manuals for P8700 - Core 2 Duo Processor
1
This manual suits for next models
1
Other Intel Computer Hardware manuals
Intel
Intel IXP2400 User manual
Intel
Intel SROMBSASMR Installation manual
Intel
Intel LGA1155 SOCKET - THERMAL MECHANICAL S AND DESIGN GUIDELINES... User manual
Intel
Intel E5420 - CPU XEON QUAD CORE 2.50GHZ FSB1333MHZ 12M LGA771 HALOGEN FREE... User manual
Intel
Intel Processor IQ80332 User manual
Intel
Intel SRCU41L - RAID Controller User manual
Intel
Intel CELERON PROCESSOR E3000 - THERMAL AND MECHANICAL... Guide
Intel
Intel E42249-003 Owner's manual
Intel
Intel X3350 - Xeon 2.66 Ghz 12M L2 Cache 1333MHz FSB LGA775 Quad-Core... Guide
Intel
Intel I7-900 DESKTOP PROCESSOR - VOLUME 1 User manual
Intel
Intel 945GME User manual
Intel
Intel I5-520E - ADDENDUM User manual
Intel
Intel Core 2 Quad Q9400 Reference guide
Intel
Intel BX80623I52500K User manual
Intel
Intel Pentium 4 mPGA478 User manual
Intel
Intel RS3FC044 User manual
Intel
Intel RS2BL080DE User manual
Intel
Intel Pentium 4 Guide
Intel
Intel NUC 11 Extreme Kit NUC11BTMi9 User manual
Intel
Intel ESM-2740 User manual
Popular Computer Hardware manuals by other brands
Mellanox Technologies
Mellanox Technologies MCX313A-BCBT? MCX314A-BCBT user manual
Silicon Laboratories
Silicon Laboratories BRD4204D user guide
Vega
Vega ARIES IoT Product reference manual
FabiaTech
FabiaTech FB2412 Series User's quick setting
National Instruments
National Instruments 6008 USER GUIDE AND SPECIFICATIONS
MicroElektronika
MicroElektronika Mikromedia user manual