Intel NUC 11 Extreme Kit NUC11BTMi9 User manual

1
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021
Intel® NUC 11 Extreme Kit NUC11BTMi7
Intel® NUC 11 Extreme Kit NUC11BTMi9
User Guide
August 2021

2
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021
You may not use or facilitate the use of this document in connection with any infringement or other legal analysis concerning Intel products
described herein. You agree to grant Intel a non-exclusive, royalty-free license to any patent claim thereafter drafted which includes subject
matter disclosed herein.
No license (express or implied, by estoppel or otherwise) to any intellectual property rights is granted by this document.
All information provided here is subject to change without notice. Contact your Intel representative to obtain the latest Intel product
specifications and roadmaps.
The products described may contain design defects or errors known as errata which may cause the product to deviate from published
specifications. Current characterized errata are available on request.
Copies of documents which have an order number and are referenced in this document may be obtained by calling 1-800-548-4725 or by
visiting: http://www.intel.com/design/literature.htm.
Intel technologies' features and benefits depend on system configuration and may require enabled hardware, software or service activation.
Performance varies depending on system configuration. No computer system can be absolutely secure.
Intel and the Intel logo are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
*Other names and brands may be claimed as the property of others.
Copyright © 2021, Intel Corporation. All rights reserved.

3
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021
Contents
1.0 Introduction ............................................................................................................................. 5
1.1 Before You Begin ........................................................................................................................................... 5
1.2 Installation Precautions ............................................................................................................................. 5
1.3 Observe Safety and Regulatory Requirements ......................................................................... 6
2.0 Open the Chassis ................................................................................................................... 7
3.0 System Memory ....................................................................................................................13
4.0 Change the M.2 SSD ...........................................................................................................16
5.0 Close the Chassis .................................................................................................................20
6.0 Connect Power ......................................................................................................................26
7.0 Install an Operating System .........................................................................................28
8.0 Install the Latest Device Drivers and Software ................................................29

4
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021
Revision History
Date Revision Description
August 2021 1.0 Initial release.

5
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021
1.0 Introduction
This User Guide provides step-by-step installation instructions for these products:
 Intel® NUC 11 Extreme Kit NUC11BTMi7
 Intel® NUC 11 Extreme Kit NUC11BTMi9
1.1 Before You Begin
CAUTIONS
The steps in this guide assume you’re familiar with computer terminology and
with the safety practices and regulatory compliance required for using and
modifying computer equipment.
Disconnect the computer from its power source and from any network before
performing any of the steps described in this guide.
Failure to disconnect power, telecommunications links, or networks before you open
the computer or perform any procedures can result in personal injury or equipment
damage. Some circuitry on the board can continue to operate even though the front
panel power button is off.
Follow these guidelines before you begin:
 Always follow the steps in each procedure in the correct order.
 Create a log to record information about your computer, such as model,
serial numbers, installed options, and configuration information.
 Electrostatic discharge (ESD) can damage components. Perform the
procedures described in this chapter only at an ESD workstation using an
antistatic wrist strap and a conductive foam pad. If such a station isn’t
available, you can provide some ESD protection by wearing an antistatic wrist
strap and attaching it to a metal part of the computer chassis.
1.2 Installation Precautions
When you install and test the Intel NUC, observe all warnings and cautions in the
installation instructions.
To avoid injury, be careful of:

6
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021
 Sharp pins on connectors
 Sharp pins on circuit boards
 Rough edges and sharp corners on the chassis
 Hot components (such as SSDs, processors, voltage regulators, and heat sinks)
 Damage to wires that could cause a short circuit
Observe all warnings and cautions that instruct you to refer computer servicing
to qualified technical personnel.
1.3 Observe Safety and Regulatory Requirements
If you don’t follow these instructions, you increase your safety risk and the possibility
of noncompliance with regional laws and regulations.

7
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021
2.0 Open the Chassis
1. Unscrew the four screws on the rear side of the chassis and shift the cover:
2. Remove back panel:

8
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021
3. Remove the both side panels:

9
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021
4. Flip the top fan lid:

10
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021
5. Flip PCIe bracket holder down:

11
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021
6. Remove Compute Element air flow cover:

12
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021
7. Remove Compute Element fan assembly:

13
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021
3.0 System Memory
Intel® NUC kit NUC11BTMi7 and NUC11BTMi9 have two 260-pin DDR4 SO-DIMM
sockets. Be sure to select memory modules that meet these requirements:
 1.2V low voltage memory
o 1.35V via XMP support
 3200 MHz SO-DIMMs
 Max capacity - 64GB
 Non-ECC
Find compatible memory modules in the Intel Product Compatibility Tool
 NUC11BTMi7
 NUC11BTMi9
NOTE If you plan to install only one memory module, install it in the left
(SODIMM0) memory socket.
To install memory, follow these steps:
1. Observe the precautions in "Before You Begin" on page 5.
2. Turn off all peripheral devices connected to the computer. Turn off the
computer and disconnect the power cord.

14
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021
3. Align the small space at the bottom edge of the memory module with the
key in the socket.
4. Insert the bottom edge of the module at a 45-degree angle into the socket (A).
5. When the module is inserted, push down on the outer edge of module
until the retaining clips snap into place (B).

15
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021
To remove a SO-DIMM, follow these steps:
1. Observe the precautions in "Before You Begin" on page 5.
2. Turn off all peripheral devices connected to the computer. Turn off the
computer and disconnect the power cord.
3. Remove the computer’s bottom chassis cover.
4. Gently spread the retaining clips at each end of the memory socket, which
causes the module to pop out of the socket.
5. Holding the module by the edges, lift it away from the socket, and store it in an
anti-static package.
6. Reinstall and reconnect any parts you removed or disconnected to reach the
memory sockets.
7. Replace the computer’s cover and reconnect the power cord.

16
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021
4.0 Install an M.2 SSD
Intel® NUC kit NUC11BTMi7 and NUC11BTMi9 support 2x 42mm/80mm, 1x80mm, and
1x 80/110mm SSDs. The compute element supports 2x42mm or 3x 80mm. Under the
chassis SSD compartment supports 1x 80/110mm.
There are no pre-installed SSD available out of the box for the above SKUs.
Find compatible M.2 SSDs in the Intel Product Compatibility Tool:
 NUC11BTMi7
 NUC11BTMi9
To install an M.2 SSD:
1. Remove the small silver screw from the 110mm, 80mm or 42mm metal standoff
on the board.
2. Remove the pre-installed SSD from the connector if there are any.
3. Make sure there is the metal standoff in the right position, depending on the
length of the SSD you are going to install.
4. Align the space at the bottom of the new M.2 SSD to the key on the connector.
5. Secure the card to the standoff with the small silver screw.

17
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021

18
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021

19
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021

20
NUC11BTMi7, NUC11BTMi9
User Guide – August 2021
5.0 Close the Chassis
After all components have been installed, close the Intel NUC chassis. Intel
recommends this be done by hand with a screwdriver to avoid over-tightening and
possibly damaging the screws.
1. Close the NUC door and connect two bottom screws: