Intelbras IVP 4101 PET User manual

User manual
IVP 4101 PET smart

IVP 4101 PET smart
Passive infrared sensor
Congratulations, you have just purchased a product with Intelbras quality and safety.
The passive infrared sensor IVP 4101 PET smart was developed by Intelbras with
100% digital technology. The sensor has an integrated Temperature Sensor to offer
the same detection sensitivity in different environments (from -10 °C to + 50 °C)
reducing the risk of false triggers, DIGITAL technology, SMD mounting. Indicated for
INDOOR ENVIRONMENTS with the presence of pets weighing up to 20 Kg, it is easy
to install because it is wireless and can be installed in most devices that work at the
same frequency and modulation available on the market.

Care and safety
» This product is intended for Indoor environments.
» It is important to note that the Pet function is designed for crawling animals, so if the animal is not on the ground, but
on top of a bench, for example, it can be detected thus canceling the Pet function, as can be seen in the image below:
» Avoid touching the surface of the PIR, if necessary, use a soft cloth for cleaning.
» Do not place objects in front of the sensor. To secure the detection area, avoid curtains, screens, screens, or any object
that blocks the scan.
» Wireless communication technology, when exposed to environments with high power radiation, can suffer interference
and have its performance impaired. Example: locations near TV towers,AM/FM radio stations, ham radio stations, routers,
etc.
» Recommended installation height is 1.8 to 2.2 meters.
» Do not use the sensor in areas with sudden changes in temperature such as air conditioners and heaters, fans, refrigera-
tors and ovens. Do not expose the sensor directly or to sunlight reections.
» For the use of the articulator, we recommend that the installation be done by a professional installer, as its incorrect use
may affect the sensor’s coverage angle.

» The sensor must be installed where a possible intruder is easily detected, that is, where there is movement across the
sensor’s detection beams.
» We recommend that the sensor conguration is done according to item 5. Conguring the sensor IVP 4101 PET smart
(for cards in version 4410350/5 and rmware 3.0.0) and item 8. Conguring the sensor IVP 4101 PET smart (for cards
version 4410350/4 and rmware 2.2.1 o earlier).
» LGPD – General Personal Data Protection Law: Intelbras does not access, transfer, capture or perform any other type of
processing of personal data from this product.

Summary
1. Technical specications 6
2. Characteristics 6
3. Product 6
3.1. Detection range ............................................................................7
4. Installing the smart IVP 4101 PET sensor 7
5. Conguring the IVP 4101 PET smart sensor (for cards in version 4410350/5 and rmware 3.0.0) 9
5.1. Sensitivity adjustment of the smart IVP 4101 PET sensor..............................................9
5.2. Setting the operating mode of the smart IVP 4101 PET sensor .........................................9
5.3. IVP 4101 PET smart sensor supervision adjustment.................................................10
6. Low battery sensor 11
7. Test 12
8.Conguring the IVP 4101 PET smart sensor (for board version 4410350/4 and rmware 2.2.1 o earlier) 12
8.1. Sensitivity adjustment of the smart IVP 4101 PET sensor.............................................12
8.2. Setting the operating mode of the smart IVP 4101 PET sensor ........................................12
8.3. IVP 4101 PET smart sensor supervision adjustment.................................................13
9. Homologation 14
Warranty term 15

6
1. Technical specications
Coverage - Detection Angle 90°
Detection range 12 m
Operating Temperature - 10 °C to + 50 °C
Transmission frequency 433,92 MHz
Sensitivity Levels 2
Immunity to animals 20 kg
Installation height Check item 4. Installing the smart IVP 4101 PET sensor in this manual
Detection method PIR
Battery LITHIUM CR123A 3 V
Supervision Supervised (FSK) or unsupervised (OOK)
Anti-jamming Immunity against interference from malicious signals
2. Characteristics
» Digital micro-processed detection technology.
» 2 levels of sensitivity.
» 2 modes of operation, CONT (Continuous Intelligent) and ECO (Economy).
» Battery level sensor.
» No articulator required for wall installation.
» Passive infrared with dual element.
» Triggered by motion detection.
» Power: LITHIUM 3 Vdc battery – CR123A.
» Immunity to crawling pets up to 20 kg.
» Ease of installation.
3. Product
Top front cover
Lower front cover
Flat Fresnel Lens
PIR
Jumper ECO/CONT (JP2)
Jumper SENS (JP1)
Jumper SUPERV (JP3)
Battery

7
3.1. Detection range
Upper view
90°
Distance (m)
Side view
1,8 m ~ 2,20 m
Height (m)
4. Installing the smart IVP 4101 PET sensor
Before starting the installation it is necessary to dene the height of installation of the sensor. We recommend that this
sensor is installed as per the table below.
d
h
Distance (d) Pet Installation height (h)
Less than or equal to 4 m Without the presence of a pet 1,8 to 2 m
With the presence of a pet
Greater than 4 m up to 12 m With the presence of a pet 2,1 to 2,2 m
Without the presence of a pet 1,8 to 2,2 m
Note: to install the IVP 4101 PET smart sensor, make sure that the battery is not connected to the board.
The sensor IVP 4101 PET smart does not have an articulator. So for your installation, follow the procedure below:
» Step 1: remove the lower front cover from the sensor.

8
» Step 2: if the installation is done directly on the wall, use the oblong located in the upper rear region of the sensor and
the hole indicated for placement of the screw just below the connectors.
Screw hole
Oblongo
» Step 3: if the installation is done in the corner of the wall. Use the holes indicated on the back cover.
Fixing location of the screws for
installation in the wall corner.
Important: the IVP 4101 PET smart was designed for INDOOR AND CLOSED AREAS and with the presence of animals of
up to 20 kg, so do not use it for protection of outdoor or open areas and with the presence of animals of more than 20 kg.

9
5. Conguring the IVP 4101 PET smart sensor (for cards in
version 4410350/5 and rmware 3.0.0)
After the sensor is properly installed, make the following adjustments according to the information below:
5.1. Sensitivity adjustment of the smart IVP 4101 PET sensor
The SENS jumper (JP1) is used to control the detection sensitivity. With jumper JP1 open the sensor provides maxi-
mum sensitivity. With jumper JP1 closed the sensor provides minimum sensitivity. Closed factory default.
5.2. Setting the operating mode of the smart IVP 4101 PET sensor
Via the ECO/CONT jumper (JP2), select between intelligent continuous mode and economy mode. With jumper JP2
open the sensor is in intelligent continuous mode. With jumper JP2 closed, the sensor is in economy mode. Factory
default: closed.
After energized, the sensor will operate in the test period for 15 minutes so that the installer can make all the sensor
positioning adjustments. During this period, at any motion detection, the LED lights up and a trigger is generated.
Then the sensor will operate according to the congured mode.
Intelligent Continuous Mode: the sensor takes a reading of the environment and generates a trigger for 3 move-
ments, after this trigger generation the sensor goes into hibernation for 2 minutes. During this period, the indication
LED is not activated and no new triggers are generated, as a notication has just been sent to the control panel.After
the sleep time, the sensor is monitoring the environment until detecting 3 more events.
Note: this mode of operation causes a greater consumption of battery power, especially where there is a large
number of people.
Trial period
15 min
Period of
stabilization
Time the sensor remains on
Smart Continuous Mode
2 min
After inserting
the battery,
the LED is
blinking and
there is no
detection.
At any detection
the LED lights
up and
generates a
trigger.
The sensor detects (lights the
LED and generates a trigger) for
the next 3 movements, after
which it goes into hibernation.
During this period the
LED does not light and
no new triggers are
generated.
After the
hibernation time,
the sensor returns to
detect and generate
triggers in the
central, starting the
cycle again.
Período
de teste
15 min
Período de
estabilização
Tempo em que o sensor permanece ligado
Modo Contínuo inteligente
2 min
Após colocar a
bateria, o LED
ca piscando
e não há
detecção.
A qualquer
detecção o LED
acende e gera
um disparo.
O sensor detecta (acende o LED
e gera um disparo) para os
próximos 3 movimentos, após,
entra em hibernação.
Durante esse período o
LED não acende e não
são gerados novos
disparos.
Passando o tempo
de hibernação o
sensor volta a
detectar e gerar
disparos na
central, iniciando o
ciclo novamente.
Período
de teste
15 min
Período de
estabilização
Tempo em que o sensor permanece ligado
Modo Contínuo inteligente
2 min
Após colocar a
bateria, o LED
ca piscando
e não há
detecção.
A qualquer
detecção o LED
acende e gera
um disparo.
O sensor detecta (acende o LED
e gera um disparo) para os
próximos 3 movimentos, após,
entra em hibernação.
Durante esse período o
LED não acende e não
são gerados novos
disparos.
Passando o tempo
de hibernação o
sensor volta a
detectar e gerar
disparos na
central, iniciando o
ciclo novamente.

10
Economy Mode: the sensor takes a reading of the environment and right after motion is detected and the trigger
is generated, it goes into sleep, which can last for a period of 30 seconds (environment with little movement) up to
2 minutes (environment with a lot of movement). During this period, the LED indication is not activated and no new
triggers are generated,as a notication has just been sent to the switch.After the sleep time, the sensor is monitoring
the environment until detecting a new movement.
» Advantage of the Economy mode: this ability to learn from the environment, means that in places with high
degrees of movement, periodic and non-continuous shots are generated, in turn, saving battery power.
Trial period
15 min
Period of
stabilization
Time the sensor remains on
Economy Mode
30 seg - 2 min
After inserting
the battery,
the LED is
blinking and
there is no
detection.
At any detection
the LED lights
up and
generates a
trigger.
After detecting the rst
movement, the sensor turns on
the LED, triggers and enters the
sleep period.
During this period the
LED does not light and
no new triggers are
generated.
After the
hibernation time, the
sensor returns to
detect and generate
triggers in the
central, starting the
cycle again.
Período
de teste
15 min
Período de
estabilização
Tempo em que o sensor permanece ligado
Modo Contínuo inteligente
2 min
Após colocar a
bateria, o LED
ca piscando
e não há
detecção.
A qualquer
detecção o LED
acende e gera
um disparo.
O sensor detecta (acende o LED
e gera um disparo) para os
próximos 3 movimentos, após,
entra em hibernação.
Durante esse período o
LED não acende e não
são gerados novos
disparos.
Passando o tempo
de hibernação o
sensor volta a
detectar e gerar
disparos na
central, iniciando o
ciclo novamente.
Período
de teste
15 min
Período de
estabilização
Tempo em que o sensor permanece ligado
Modo Contínuo inteligente
2 min
Após colocar a
bateria, o LED
ca piscando
e não há
detecção.
A qualquer
detecção o LED
acende e gera
um disparo.
O sensor detecta (acende o LED
e gera um disparo) para os
próximos 3 movimentos, após,
entra em hibernação.
Durante esse período o
LED não acende e não
são gerados novos
disparos.
Passando o tempo
de hibernação o
sensor volta a
detectar e gerar
disparos na
central, iniciando o
ciclo novamente.
5.3. IVP 4101 PET smart sensor supervision adjustment
The SUPERV (JP3) jumper is used to select between supervised (FSK) or unsupervised (OOK) modes.With jumper JP3 open
the sensor is in supervised mode (FSK). With jumper JP3 closed the selected mode is unsupervised (OOK). The type of
supervision to be used will depend on the receiver’s compatibility with the Control Panel.
Factory standard: unsupervised

11
6. Low battery sensor
The IVP 4101 PET smart sensor controls the battery level. If it is critical (equal to or below 2.5V), it will send the information
to the control panel.
If the sensor is congured in unsupervised mode (OOK) and the low battery signal is enabled in the control unit, the
information is sent during the trip. Otherwise, if the sensor is congured in supervised mode (FSK), low battery sending is
done during supervision and triggering.
Note: consult the control panel manual to verify compatibility with low battery signaling and supervision.
To make the desired adjustments, follow the steps below:
» Open the IVP 4001 PET smart.
» Set the jumpers to the desired settings.
» Take a trigger to effect changes to the sensor conguration.
Note: do not register the sensor in the central during the stabilization time, wait for it to start working in continuous mode.
To register the sensor code in the alarm control panel, check the procedure in the manual of the used alarm control panel
and trigger a trigger by moving in front of the sensor to complete its registration.
Jumper SENS (JP1)
Position Condition
1Maximum sensitivity
2Minimal sensitivity
Jumper SUPERV (JP3)
Position Condition
Closed No (Unsupervised)
Open Yes (Supervised)
Jumper INT/CONT (JP2)
Position Condition
1Smart Continuum
2Economic
JP3
SUPERV JP1 JP2
NÃO/SIM SENS ECO/CONT

12
7. Test
Once installed and energized, walk in the area to be protected simulating a possible intrusion. Observe if the sensor is
able to detect your movements during the journey, by lighting the lens. Adjust its sensitivity if necessary or reposition the
sensor installation.
If the alarm control panel used is Intelbras, put it in test mode, this way it will not be necessary to observe the LED, as the
control panel will indicate the sensor’s operation through siren beeps.
8. Conguring the IVP 4101 PET smart sensor (for board ver-
sion 4410350/4 and rmware 2.2.1 o earlier)
8.1. Sensitivity adjustment of the smart IVP 4101 PET sensor
The SENS jumper (JP1) is used to control the detection sensitivity. With jumper JP1 open the sensor provides maximum
sensitivity. With jumper JP1 closed the sensor provides minimum sensitivity. Factory default: closed.
8.2. Setting the operating mode of the smart IVP 4101 PET sensor
Via the ECO/CONT jumper (JP2), select between intelligent continuous mode and economy mode. Factory default economy
mode.
With jumper JP2 closed, the sensor will operate in economy mode, working as follows: After power supply, the sensor
will work continuously for 30 minutes so that the installer can make all the adjustments to the sensor. After this time the
sensor enters economy mode.
Eco-mode operation
The sensor will detect and transmit 1 (once) to the control panel, after this trigger, the sensor enters economic mode (low
consumption mode without detection). In this mode, the sensor will again detect and transmit to the alarm center only
after 2 (two) minutes of no movement in the environment. After 2 (two) minutes, the sensor will be able to detect and
transmit the event to the central alarm. For a better understanding of Economy mode, see the timeline below.

13
30 min
After placing
the battery the sensor
stays in stabilization
and the LED stays
blinking. Note: do not
register the
sensor on switch in this
period, wait 50 sec so
that the sensor enter
mode continuous.
In this mode any
detection o LED
lights up and
generates ring.
No
detects
mode
Stabili-
zation
50 sec
Continuous
mode
Time the sensor remains on.
Economical mode
2 min
In this mode the
sensor detects the rst
movement and gene-
rates a trigger, howe-
ver it goes into hiber-
nation and detects
again after two minu-
tes without movement
in the place, in the
hibernation period the
LED does not light.
In this 2 min
period, if there is
movement in
place, the sensor
waits for the last
movement to
start counting
down the two
minutes.
After 2 minutes of
the last movement
of the site, the
sensor detects and
generates a trip at
the control panel.
With jumper JP2 open, the sensor will work in CONT (intelligent continuous) mode, operating as follows:After power-up,
the sensor will work continuously for 30 minutes so that the installer can make all the adjustments to the sensor.
After this time the sensor goes into smart continuous mode.
Smart continuous mode operation
The sensor can transmit up to 3 consecutive shots, after the last shot, the sensor goes into HIBERNATION mode (low
consumption mode without transmission to the alarm center) for 2 (two) minutes.The sensor will only detect and transmit
a trigger again if there is 2 (two) minutes without movement in the environment.After the 2 (two) minutes the sensor will
be able to transmit up to 3 consecutive shots within an interval of 135 seconds if there are movements. Right after the 3
shots or an interval of 135 seconds, the sensor will enter the SLEEP period, that is, it needs to stay again for two minutes
without movement to be able to detect and transmit a shot. During this period of hibernation the sensor will not transmit
to the control panel, but the LED will light indicating that the sensor is detecting normally.
For a better understanding of the smart continuous mode, check the timeline below:
30 min
After placing
the battery the sensor
stays in stabilization
and the LED stays
blinking. Note: do not
register the
sensor on switch in this
period, wait 50 sec so
that the sensor enter
mode continuous.
In this mode any
detection o LED
lights up and
generates ring.
No
detects
mode
Stabili-
zation
50 sec
Continuous
mode
Time the sensor remains on.
Smart continuous mode
2 min
In this mode the
sensor can shoot and
to transmit up to 3
times in a break
maximum of 135
seconds before to
enter the way of
hibernation.
In this period of
2 min, if there is
movement in the
place, the sensor
waits for the last
movement to
start counting
the two minutes.
In the period of
hibernation only
the LED lights up
indicating that the
sensor is detecting
normally.
in this mode the
sensor needs go 2
minutes without
detect motion to
return to shoot and
transmit to alarm
central.
8.3. IVP 4101 PET smart sensor supervision adjustment
The OOK/FSK jumper (JP3) is used to select the modulation. With jumper JP3 open the sensor is in supervised mode (FSK).
With jumper JP3 closed the selected mode is unsupervised (OOK). The type of supervision to be used will depend on the
receiver’s compatibility with the Control Panel.
Factory standard: unsupervised

14
9. Homologation
3685-15-0160
This equipment operates on a secondary basis, that is, it is not entitled to protection against harmful interference,
even from stations of the same type, and may not cause interference to systems operating on a primary basis. This
is a product approved by Anatel, the approval number can be found on the product label, for queries go to the
website: sistemas.anatel.gov.br/sch.

15
Warranty term
It is established that this warranty is granted upon the following conditions:
Client’s name:
Client’s signature:
Invoice number:
Date of purchase:
Model: Serial number:
Retailer:
1. All the parts, pieces and components of the product are guaranteed against possible manufacturing defects, which may
arise, for the term of 1 (one) year, with a term of 3 (three) months’ legal warranty plus 9 (nine) months’ contractual
warranty –, counting from the date of purchase of the product by the Consumer, as appears in the product purchase bill
of sale, which is an integral part of thisTerm throughout the domestic territory.This contractual warranty includes the free
exchange of parts, pieces and components which have a manufacturing defect, including the expenses with labor used in
this repair. If there is no manufacturing defect, but defect(s) arising from misuse, the Consumer shall bear these expenses.
2. The installation of the product shall be executed in accordance with the Product Manual and/or Installation Guide. If your
product requires the installation and conguration by a qualied technician, seek a suitable specialized professional, the
costs of these services not being included in the product amount.
3. Having perceived the defect, the Consumer shall immediately contact the nearest Authorized Service which appears in
the report offered by the manufacturer – they are the only ones authorized to examine and remedy the defect during the
warranty term foreseen herein. If this is not respected, this warranty shall lose its validity, as it shall be characterized as
product infringement.
4. If the Consumer requests home service, it shall contact the nearest Authorized Service to inquire about the technical visit
rate. If it is necessary to remove the product, the ensuing expenses, such as those of transportation and insurance of the
taking and return of the product, shall be the Consumer’s responsibility.
5. The warranty shall lose its validity totally in the occurrence of any of the following cases: a) if the defect is not one of manu-
facture, but is caused by the Consumer or by third parties foreign to the manufacturer; b) if the damage to the product arises
from accidents, disasters, agents of nature (lightning, oods, landslides, etc.), humidity, voltage in the electrical network
(excess voltage caused by accidents or excessive uctuations in the network), installation/use in disagreement with the
user’s manual or arising from natural wear of the parts, pieces and components; c) if the product has undergone effects of a
chemical, electromagnetic, electrical or animal (insects, etc.) nature; d) if the serial number of the product has been falsied
or erased; e) if the appliance has been infringed.
6. This warranty does not cover loss of data; therefore, it is advisable that if it is the case of the product, the Consumer makes
a backup regularly of the data which appears in the product.
7. Intelbras is not responsible for the installation of this product, or for possible attempts at fraud and/or sabotage in its
products. Maintain the updates of the software and applications used up-to-date, if it is the case, as well as the network
protection required for defense against hackers. The equipment is guaranteed against defects in its usual conditions of use,
it being important to bear in mind that, as it is electronic equipment, it Is not free of fraud and scams which may interfere
with its correct functioning.
8. After its useful life, the product must be delivered to an authorized Intelbras service center or directly disposed of in an
environmentally appropriate manner to avoid environmental and health impacts. If you prefer, the battery, as well as other
unused Intelbras brand electronics, can be disposed of at any Green Eletron collection point (waste management facility
to which we are associated). If you have any questions about the reverse logistics process, please contact us at (48) 2106-
0006 or 0800 704 2767 (Monday to Friday 8am to 8pm and Saturdays 8am to 6pm) or via -mail [e-mail].
These being the conditions of this complementary Warranty Term, Intelbras S/A reserves the right to alter the general,
technical and esthetic features of its products without prior notice.
The manufacturing process of this product is not covered by the requirements of ISO 14001.
All the images of this manual are illustrative.
Product benefiting from the Legislation of Informatics.

01.22
Made in Brazil
Customer Support: (48) 2106 0006
Forum: forum.intelbras.com.br
Support via chat: chat.intelbras.com.br
Support via e-mail: [e-mail]
Customer Service: 0800 7042767
Where to buy? Who installs it? 0800 7245115
Produced by: Intelbras S/A – Indústria de Telecomunicação Eletrônica Brasileira
Rodovia BR 459, km 124, 1325 – Distrito Industrial – Santa Rita do Sapucaí/MG – 37540-000
CNPJ 82.901.000/0016-03 – www.intelbras.com.br