Intellinet 524377 (Annex b) User manual

wireless N
ADsl2+
4-port
router
quick
iNstAll
guiDe
MODELS 524360 (ANNEX A)
& 524377 (ANNEX B)
INT-524360/524377-QIG-1208-01

Thank you for purchasing the INTELLINET NETWORK SOLUTIONS™Wireless N
ADSL2+ 4-Port Modem Router, Model 524360 (Annex A) or Model 524377
(Annex B).
An all-in-one modem, router, Wireless N access point, firewall and Fast Ethernet
4-port switch, it allows you to access the Internet and download music, play
interactive games online or surf the Web at double the speed previously available
through ADSL2.
This quick install guide presents the rudimentary steps required to set up and
operate this device. For more detailed instructions and specifications, refer to the
user manual 1) on the CD enclosed with this product; 2) on the Web site listed
below; or 3) in some cases, printed and enclosed with this product. Contact
your INTELLINET NETWORK SOLUTIONS dealer with comments or questions,
or visit www.intellinet-network.com for information on the latest software and
firmware updates, related products and additional contact information.
fcc regulAtory stAtemeNts
FCC Part 68
This equipment complies with Part 68 of FCC Rules. On the bottom of this device is
a label with the FCC registration number and ringer equivalence number (REN) for
this equipment. You must provide this information to the telephone company upon
request. The REN is useful to determine the quantity of devices you may connect to
the telephone line and still have all of those devices ring when your number is called.
In most areas, the total of the REN of all devices connected to one line should not
exceed five. To be certain of the number of devices you may connect to your line,
as determined by the REN, contact your local telephone company.
If the modem causes harm to the telephone network, the telephone company may
discontinue your service temporarily, notifying you in advance (if feasible) or as
soon as possible. You will be advised of your right to file a complaint with the FCC.
Also, the telephone company may make changes in its facilities, equipment,
operations or procedures that could affect the proper operation of your equipment.
If they do, you will be notified in advance to give you an opportunity to maintain
uninterrupted telephone service.
If you experience trouble with this device, contact your INTELLINET NETWORK
SOLUTIONS™dealer for repair/warranty information. The telephone company
may ask you to disconnect this equipment from the network until the problem has
been corrected or until you are sure that the equipment is not malfunctioning.
This equipment may not be used on coin service provided by the telephone
company. Connection to party lines is subject to state tariffs.
Installation
This device is equipped with a USOC RJ-11C connector.
2

FCC Part 15
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This equipment must be installed and operated in accordance with provided
instructions, and a minimum of 20 cm spacing must be provided between computer-
mounted antenna and a person’s body (excluding extremities of hands, wrists and
feet) during wireless modes of operation.
This device complies with Part 15 of FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation. Any changes or modifications not expressly approved by the
party responsible for compliance could void the authority to operate equipment.
Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall not
be less than 20 cm (8 inches) during normal operation. The antenna(s) used
for this transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
R&TTE Compliance Statement
This equipment complies with all the requirements of Directive 1999/5/EC of the
European Parliament and the Council of March 9, 1999, on radio equipment and
telecommunications terminal equipment and the mutual recognition of their conformity
(R&TTE). The R&TTE Directive repeals and replaces Directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station Equipment) as
of April 8, 2000.
3

Safety
This equipment is designed with the utmost care for the safety of those who install
and use it. However, special attention must be paid to the dangers of electric
shock and static electricity when working with electrical equipment. All guidelines
of the FCC and of the computer manufacturer must therefore be followed at all
times to ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria,
Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg,
the Netherlands, Portugal, Spain, Sweden and the United Kingdom.
The ETSI version of this device is also authorized for use in EFTA member states
Iceland, Liechtenstein, Norway and Switzerland.
EU Countries Not Intended for Use
None.
pAckAge coNteNts
• Wireless N ADSL2+ 4-Port Modem Router, Model 524360 (Annex A) or
Model 524377 (Annex B)
• Power adapter
• Ethernet Cat5 RJ-45 cable, 1.0 m (3 ft.)
• RJ-11 telephone cable, 1.8 m (6 ft.)
• Quick install guide
• Setup CD with user manual and setup wizard
hArDwAre
Front Panel
As listed below, the LED s indicate the current status of the router.
LED Mode Status
PWR (green) On Ready for operation.
WLAN (yellow) Off The wireless LAN is disabled.
Blinking Wireless traffic is being transmitted/received.
WPS (Yellow) Off WPS function is disabled.
Blinking WPS function is enabled.
ADSL (green) On Successful connection to an ADSL DSLAN.
Blinking No connection.
LAN (LNK/ACT) On The LAN cable is connected to the router.
Ports 1-4 (green) Off No network connection.
Blinking Network traffic is being transmitted/received.
4

Rear Panel
Antenna Connectors: The reverse SMA connectors allow easy connection to
external antennas.
Reset button: This can be used to reset the router or to restore the factory default
settings. Press the button (using a pencil tip can help) for less than five seconds
to re-boot the router and save any configurations that have been set up.
If problems persist after a simple re-boot — or if you’ve forgotten your password —
hold the button in for longer than five seconds to reset the router to its factory
default settings. NOTE: The factory default settings will replace any others that
have been configured.
Power outlet: The included 12 V DC power adapter is connected here.
WPS button: Wi-Fi Protected Setup (WPS) is the simplest way to build a connection
between wireless network clients and this router. Press this button and enable the
WPS function of the wireless clients; the router and clients will automatically
configure the security key and connect directly. NOTE: The router will wait for
WPS requests from wireless clients for 2 minutes after the WPS button is pressed.
LAN ports: The four local area network (LAN) ports are for connections to PCs,
LANs, printers, servers, hubs and so forth.
ADSL: The included RJ-11 phone line connects this to an ADSL/phone network.
Connections
1. From the ADSL port, connect the router to your ADSL network using the RJ-11
telephone cable provided.
2. From any of the LAN ports, connect the router to your PC, hub, switch or
other component using the Ethernet Cat5 RJ-45 cable provided.
3. Connect the router’s power outlet to a power source using the power adapter
provided. NOTE: Use only the power adapter included with this device.
4. Check that the green ADSL LED is on, indicating a successful connection. If
the ADSL LED is blinking — indicating that no connection has been made —
contact your Internet service provider.
5

coNfigurAtioN
ISP
This router provides a setup wizard used to configure the ADSL settings. This
wizard collects and enters ADSL settings from some Internet service providers
(ISPs) simply by selecting the ISP when prompted. If you cannot find your
particular ISP listed in the wizard, refer to the Quick Start instructions in the Web
Management section of the user manual on the enclosed CD.
Before starting:
• Make sure the ADSL cable is connected to the router correctly. When the
ADSL cable is working normally, the ADSL LED will be on.
• Uninstall all dial-up programs previously installed for the USB modem or other
dial-up devices.
• It’s recommended that the router rst be congured with the Ethernet cable
connected prior to setting the wireless functions.
NOTE: This setup wizard can be run in Windows 2000, XP or Vista, though
the screen images shown may be representative of just one particular platform.
1. Insert the enclosed setup CD (featuring the setup wizard) into your CD-ROM
drive. The Autorun.exe program should be executed automatically. If not,
run Autorun.exe manually from the “Autorun” folder on the CD.
2. Click on “Setup Wizard”
when the initial menu
appears on screen. The
wizard will search for
the router. If the router
can’t be found, enter the
IP address and password
of the router, then click
“Next” to search again.
3. The wizard automatically
selects the country you’re
in (by identifying the
language of the computer’s
operating system), and
will then display the Select
ISP screen. Select the ISP.
If it’s not listed, click
“Other” to re- select the
country, or manually configure the ISP information (see Software/Setup Wizard /
Manually Set ISP in the user manual).
4. If prompted, enter the ISP-provided username and password, then click “Next.”
6

5. When the Settings
Overview screen displays,
click “Save,” which will
reboot the router.
After saving and rebooting,
the ISP settings are complete.
Click “Finish” to close the
setup wizard.
IP Address
To use the router to access the Internet, the PCs in the network must have an
Ethernet adapter installed and be connected to the router either directly or through
a hub or switch. The TCP/IP protocol of each PC has to be installed, and the IP
address of each PC has to be set in the same subnet as the router.
The router’s default IP address is 192.168.2.1; the subnet mask is 255.255.255.0.
PCs can be configured to obtain an IP address automatically through the DHCP
server of the router or a fixed IP address in order to be in the same subnet as the
router. By default, the DHCP server of the router is enabled and will dispatch an
IP address to the PC from between 192.168.2.100 and 192.168.2.200. It is
strongly recommended that IP addresses be set/obtained automatically.
This section explains how to configure a PC so that it can obtain an IP address
automatically for Windows 2000, XP or Vista. For other operating systems
(Macintosh, Sun, etc.), follow the manual of that operating system.
Wi n d o W s Vi s t a :
1. Click “Start,” select “Settings,” then go to the control panel and double-click
“Network and Sharing Center” to display its window.
2. Click “Manage network connections,” right-click on the local Area Connection
icon and select Properties. The local Area Connection screen will display.
3. Check the list of network Components. You should see “Internet Protocol
Version 4 (TCP/IPv4)” on your list. Select it and click Properties.
4. On the Internet Protocol Version 4 (TCP/IPv4) Properties screen, select “Obtain
an IP address automatically” and “Obtain DNS server address automatically.”
5. Click “OK” to confirm the setting. Your PC will obtain an IP address automatically
from the router’s DHCP server. NOTE: Make sure the router’s DHCP server is
the only one available on your LAN.
Wi n d o W s XP:
1. Click “Start,” open the control panel and then double-click “Network Connections.”
The Network Connections window will appear.
2. Right-click on the Local Area Connection icon and select Properties. The Local
Area Connection window will appear.
7

3. Check the list of Network Components. You should see “Internet Protocol
(TCP/IP)” on your list. Select it and click Properties.
4. In the Internet Protocol (TCP/IP) Properties window, select “Obtain an IP address
automatically” and “Obtain DNS server address automatically.”
5. Click “OK” to confirm the setting. Your PC will now obtain an IP address
automatically from the router’s DHCP server. NOTE: Make sure the router’s
DHCP server is the only one available on your LAN.
Wi n d o W s 2000:
1. Click “Start” and select Settings, then click “Control Panel.”
2. Double-click on the Network and Dial-up Connection icon. In the Network
and Dial-up Connection window, double-click on the Local Area Connection
icon. The Llocal Area Connection window will appear.
3. In the Local Area Connection window, click “Properties.”
4. Check your list of Network Components. You should see “Internet Protocol
(TCP/IP)” on your list. Select it and click “Properties.”
5. In the Internet Protocol (TCP/IP) Properties window, select “Obtain an IP address
automatically” and “Oobtain dnS server address automatically.”
6. Click “OK” to confirm the setting. Your PC will obtain an IP address automatically
from your router’s DHCP server. NOTE: Make sure the router’s DHCP server
is the only one available on your LAN.
After configuring the PC(s) to obtain the IP address(es) automatically, the router’s
DHCP server will automatically give LAN clients an IP address. By default, the
server is enabled to do this. Once the PC has obtained an IP address from the
router, enter the default IP address 192.168.2.1 (the router’s IP address) into the
PC’s Web browser and press “Enter.”
The login screen will appear. Enter the username and password, then click “OK”
to log in. By default, the username is “admin” and the password is “1234.”
NOTE: For security reasons, it is recommended that the password be changed
as soon as possible.
Click “OK” to continue. The Home Page screen appears, displaying seven
instructional options: Quick Start, Interface Setup, Advanced Setup, Access
Management, Maintenance, Status and Help.
8

Quick Start
The Quick Start section is designed to get you using the router as quickly as
possible. Before configuring the router, check with your ISP (Internet service
provider) as to what kind of service is provided (examples are shown in the
following table).
1. On the Home Page screen, click “Run Wizard” to start the configuration. On
the subsequent screen, click “Next” to continue.
2. Set and confirm the new
password; then click “Next”
to continue.
3. Select the time zone; then
click “Next” to continue.
9
PPPoE VPI/VCI, VC-based/LLC-based multiplexing, Username,
Password (and Service Name).
PPPoA VPI/VCI, VC-based/LLC-based multiplexing, Username,
Password.
RFC1483 Bridged VPI/VCI, VC-based/LLC-based multiplexing to use
Bridged Mode.
RFC1483 Routed VPI/VCI, VC-based/LLC-based multiplexing, IP Address,
Subnet Mask, Gateway Address and Domain Name
System (DNS) IP Address (a fixed IP Address).

4. Select your Internet
connection type (as
directed by your ISP); then
click “Next” to continue.
5. Enter the data provided
by your ISP; then click
“Next” to continue.
6. Click “Next” to save the
settings and restart the
router.
10

INTELLINET NETWORK SOLUTIONS™offers a complete line
of active and passive networking products.
Ask your local computer dealer for more information or visit
www.intellinet-network.com.
Copyright © INTELLINET NETWORK SOLUTIONS
All products mentioned are trademarks or registered trademarks of their respective owners.